Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Equinox Systems EQLED12B
Summary of Contents for Equinox Systems EQLED12B
- Page 1 DJ Booth White LED Starcloth User Manual Order code: EQLED12B...
-
Page 2: Safety Advice
Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! • Before your initial start-up, please make sure that there is no damage caused during transportation. • Should there be any damage, consult your dealer and do not use the equipment. • To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. • Please note that damages caused by user modifications to this equipment are not subject to warranty. CAUTION! CAUTION! TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT! AWAY FROM RAIN, HIGH VOLTAGE-RISK MOISTURE AND LIQUIDS OF ELECTRIC SHOCK!! IMPORTANT:... - Page 3 Product overview & technical specifications DJ Booth White LED Starcloth Upgrade your Equinox DJ MICRON Booth with this black starcloth featuring 72 x 5mm LEDs. The Starcloth is supplied complete with a comprehensive controller featuring Auto, Sound Active and DMX control options. Additionally you can create a white starcloth effect when combining the white lycra supplied with the EQLED12L and this black starcloth. Cloth: 72 x 5mm white LEDs Fast fixx velcro tabs Low reflection, fire retardant material Controller: DMX channels: 5 Sound active, auto run and auto fade modes IEC power in socket 3-pin XLR DMX in/out sockets 205mm Specifications Controller Power supply 100~240V, 50/60Hz Fuse T1A 250V Dimensions 55 x 205 x 145mm WHITE STARCLOTH CONTROLLER ENTER DOWN 145mm WHITE STARCLOTH CONTROLLER ENTER...
-
Page 4: Technical Specifications
Technical specifications WHITE STARCLOTH CONTROLLER ENTER DOWN WHITE STARCLOTH CONTROLLER ENTER DOWN WHITE STARCLOTH CONTROLLER ENTER DOWN PUSH OUTPUT TO FUNCTION DMX OUT DMX IN STARCLOTH PUSH PUSH www.prolight.co.uk OUTPUT TO FUNCTION DMX OUT DMX IN STARCLOTH OUTPUT TO FUNCTION DMX OUT DMX IN STARCLOTH... -
Page 5: Operating Instructions
Operating instructions Auto mode To access the auto mode, press the “UP/DOWN” buttons on the front of the unit to show “Auto” on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the auto mode you require. Press the “ENTER” button to confirm the setting. Now use the “UP” and “DOWN” buttons to set the the speed required. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “ESC” button. Fade mode To access the fade mode, press the “UP/DOWN” buttons on the front of the unit to show “FAde” on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the the speed required. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “ESC” button. Sound active mode To access the sound active mode, press the “UP/DOWN” buttons on the front of the unit to show “Soud” on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the sound program you require. Press the “ENTER” button to confirm the setting. Now use the “UP” and “DOWN” buttons to set the the sound sensitivity (00: lowest, 31: highest). Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “ESC” button. Pattern mode: To access pattern mode, press the “UP/DOWN” buttons on the front of the unit to show “PAtt” on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the brightness of LED string 1. Press the “ENTER” button to confirm the setting. Repeat this step for LED string 2 - 4. Press the “ENTER” button to confirm the setting. Now use the “UP” and “DOWN” buttons to set the the flash speed required. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “ESC” button. Slave mode: To access the slave mode, press the “UP/DOWN” buttons on the front of the unit to show “SLav” on the LED display. The unit is now in slave mode. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “ESC” button. DMX address: To change the DMX address, press the “UP/DOWN” buttons on the front of the unit to show “Addr” on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the address you require. Press the “ENTER” button to confirm the setting. This is also the... -
Page 6: Software Version
Operating instructions Software version: To view the software version of the controller use the “UP/DOWN” buttons on the front of the unit to show “VEr ” on the LED display. Now press the “ENTER” button and the version will be displayed in the format “V---”. To exit out of any of the above options, press the “ESC” button. Static mode: To access the static mode, press the “UP/DOWN” buttons on the front of the unit to show “StAt” on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the static mode you require between “S000 - S015”. S000 Blackout S008 LED group 2 & 3 on S001 LED group 1 on S009 LED group 2 & 4 on S002 LED group 2 on S010 LED group 3 & 4 on S003 LED group 3 on S011 LED group 1, 2 & 3 on S004 LED group 4 on S012 LED group 1, 2 & 4 on S005 LED group 1 & 2 on S013 LED group 1, 3 & 4 on S006 LED group 1 & 3 on S014 LED group 2, 3 & 4 on... -
Page 7: Dmx Setup
DMX setup Setting the DMX address: The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start address” from 1- 511. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the chain starts at 107. DMX 512: DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a data “out” terminal). DMX linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. DATA cable (DMX cable) requirements (for DMX operation): This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output, see image below. Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers. -
Page 8: Line Termination
DMX setup Notice: Be sure to follow the diagrams below when making your own cables. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behaviour. Special note: Line termination: When longer runs of cable are used, Termination reduces signal transmission you may need to use a terminator on problems and interference. It is always advisable to connect a DMX terminal, the last unit to avoid erratic behaviour. (resistance 120 Ohm 1/4 W) between pin 2 Using a cable terminator will decrease (DMX-) and pin 3 (DMX+) of the last fixture. the possibilities of erratic behaviour. (3-pin - Order code: CABL90, 5-pin - Order code: CABL89) 5-pin XLR DMX connectors: Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion. -
Page 9: Related Items
Related items Please contact your local retailer to purchase these accessories. Optional accessories Order code Overhead kit EQLED12E Black starcloth EQLED12F with tri-colour LEDs Black starcloth EQLED12B with white LEDs Black lycra EQLED12A Replacement white lycra EQLED12C Lightweight DJ Booth EQLED12L Lightweight DJ Booth Optional Black Starcloth with tri-colour LEDs and controller Order ref: EQLED12L Order ref: EQLED12F Optional Black Lycra... -
Page 10: Weee Notice
WEEE notice Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. www.prolight.co.uk DJ Booth White LED Starcloth User Manual... - Page 11 www.prolight.co.uk DJ Booth White LED Starcloth User Manual...
- Page 12 www.prolight.co.uk DJ Booth White LED Starcloth User Manual...