Advertisement
Quick Links
Advertisement
Related Manuals for Iso-Tech ICM36R
Summary of Contents for Iso-Tech ICM36R
- Page 1 INSTRUCTION MANUAL ICM36R CLAMP MULTIMETER ICM 36R...
- Page 2 ISO-TECH ICM36R CLAMP MULTIMETER INSTRUCTION MANUAL...
- Page 4 INTRODUCTION 1-1 Unpacking and Inspection Upon removing your new Current Meter from its packing, you should have the following items: 1. Current meter. 2. Carrying case. 3. Instruction Manual. 1-2 Meter Safety Terms as Marked on Equipment Attention — Refer to Manual. Double Insulation —...
- Page 5 1-3 Front Panel Refer to Figure 1 and the following numbered steps to familiarize yourself with the meter's front panel controls. 1. Digital Display — The digital display has a 3 1/2 digit LCD readout (maximum reading 1999) plus auto polarity, <...
- Page 6 Figure 1...
-
Page 7: Specifications
SPECIFICATIONS 2-1 General Specifications Display : 3 1/2 Digital Liquid Crystal Display (LCD) with a maximum reading of 1999. Polarity : Automatic polarity indicated. Overrange Indication : "1" or "-1" indicated. Measuring Rate : 2 times per second, nominal. Position Error : ± 1% of reading. Type of Sensing : Hall effect sensing for AC and DC. - Page 8 2-2 Environmental Conditions Indoor use only. Maximum Altitude : 2000 meters. Installation Category : IEC 1010 Cat. II 600V, Cat. III 300V. Pollution Degree : 2 Operating Ambient : 0°C ~ 50°C, < 75% R.H. Storage Temperature : -20°C ~ 60°C, < 80% R.H. Temperature Coefficient : 0.2 x (Specified accuracy) / °C, <...
- Page 9 2-3 Electrical Specifications Accuracy is ± (% reading + number of digits) at 23°C ± 5°C, less than 75% R.H. (1) DC A Range Resolution Accuracy ±(1.9%reading + 5digits) for 0 ~ 20A 200A 0.1A ±(1.9%reading + 3digits) for 20A ~ 200A 600A ±(1.9%reading + 3digits) for 200A ~ 600A...
- Page 10 (2) AC A Range Resolution Accuracy ±(1.9%reading + 7digits) for 0 ~ 20A 200A 0.1A ±(1.9%reading + 5digits) for 20A ~ 200A 600A ±(1.9%reading + 5digits) for 200A ~ 600A Frequency Response: 40Hz ~ 400Hz. Data Hold: Hold display reading for all functions and ranges. (3) Auto Power Off The meter will automatically shut itself off approximately 30 minutes after power on.
-
Page 11: Operation
OPERATION This instrument has been designed and tested in accordance with IEC Publication 1010, Safety Require- ments for Electronic Measuring Apparatus and has been supplied in a safe condition. This instruction manual contains some information and warnings which have to be followed by the user to ensure safe operation and to retain the instrument in safe condition. - Page 12 THIS INSTRUMENT MUST NOT BE USED ON UNINSULATED CONDUCTORS AT A VOLTAGE GREATER THAN 600V ac/dc. 3-2 AC Current Measurement 1. Set the AC/DC switch to the AC position. 2. Set the function switch to the desired range, if unsure select 600A range. 3.
- Page 13 Figure 2...
-
Page 14: Maintenance
MAINTENANCE WARNING : TO AVOID ELECTRICAL SHOCK REMOVE JAW FROM CONDUCTOR BEFORE OPENING THE BATTERY COVER. General Maintenance 1. Repairs or servicing not covered in this manual should only be performed by qualified personnel. 2. Periodically wipe the case with a damp cloth and detergent, do not use abrasives or solvents. Battery Replacement This instrument is powered by a single 9V alkaline battery. - Page 15 Asia Iso-Tech 7410 Pebble Drive 460 Alexandra Road, #15-01A Fort Worth PSA Building Texas 76118-6961 Singapore 119963 Europe Canada Iso-Tech 1701 Woodward Drive PO Box 99 Ste 108 Ottawa Corby Ontario K2C 0R4, Canada Northamptonshire NN17 9RS United Kingdom Japan...