Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AZZA CSAZ-GT1
Summary of Contents for AZZA CSAZ-GT1
- Page 1 CSAZ-GT1 INSTALLTION GUIDE www.azzatek.com RADIATOR EASY SWAP READY...
-
Page 2: Installation Instructions
Installation Instructions 1. Motherboard Tray Handle installation 2. Side Panel Disassembly 3. Front Panel Disassembly 4. Top Panel Disassembly 5. Bottom Panel Disassembly 6. Motherboard Tray Removal and Installation 7. Power Supply Installation 8. Motherboard, CPU and Graphics Card Installation 9. -
Page 3: Specifications
Specifications Model: GT 1 Model Name: CSAZ-GT 1 Model Number: Spec: ATX Full Tower Type: Black/Black (inside chassis) Color: 0.8mm SECC Material: Side Panel Window: Not Included Power Supply: up to 200mm CPU Cooler Compatibility: XL-ATX,E-ATX, Full ATX, Micro ATX Motherboard Compatibility: Rear Bottom Power Location... -
Page 4: List Of Parts
List of Parts Top Cover Left Side Panel Front Bezel 5.25”Device Cover x9 3.5”HDD, 2.5” SSD/HDD Holder x5 Bottom Dust Filter Bottom Stand Right Side Panel 5.25” Tool-less Retaining Clips Motherboard Tray Handle 2x140mm Silent Bottom Fans 2x120mm Side Fans/1x120mm Rear Fan Side 230mm Fan (optional) 2x230mm Top Fans... -
Page 5: Air Cooling System
Air Cooling System Side:1 x 120mm Silent Fan (24 dBA) Bottom:1 x 140mm Silent Fan (19 dBA) Top: 1 x 230mm LED Silent Fan (24 dBA) Back : 1 x 120mm Silent Fan (24 dBA) Diagram 241,26 605,21... -
Page 6: Assembly Kit
Assembly kit Figure Parts Name Quantity Screw for Motherboard Screw for Graphics Card Bracket Motherboard Tray Screw for2.5’’ SSD Screw for 3.5’’ HDD Power Supply Screw Screw for HDD Bracket Speaker Cable Tie Pad for Power Supply Graphics Card Support Bracket Assembly Parts Graphics Card Support Bracket M1 (metal) Graphics Card Support Bracket M2 (metal) Graphics Card Support Bracket P1 (Plastic) - Page 7 Installation Instructions 1.Motherboard Tray Handle Installation 1.1 Tighten the screws to secure the handle to the motherboard tray 2.Side Panel Disassembly 2.1 Unscrew the thumb screws on the back of the chassis 2.2 Pull the side panels toward the back of the chassis * When the motherboard is rotated 180 degree, the two side panels will need to be swapped 3.Front Panel Disassembly 3.1 Hold the bottom of the front panel, and remove the front panel as shown in the figure...
- Page 8 6.Motherboard Tray Removal and Installation 6.1 Unscrew the thumb screws on the rear and the side of the motherboard 6.2 Pull the motherboard tray out of the chassis 6.3 Rotate the motherboard tray 180 degrees 6.4 Gently slide the motherboard tray back into the chassis 6.5 Secure the motherboard tray with the provided screws * To provide better cooling performance, the suggested orientation of the graphics card is at the top of the case.
- Page 9 9.5.25” Device Installation 9.1 Pinch the 5.25” drive bay metal mesh to remove it from the front panel 9.2 Slide the 5.25” drive into the appropriate bay until the latch locks into place 9.3 To remove the 5.25” device, please push on the lever and push the device out 10.3.5”...
- Page 10 12.Fan Dust Filter Removal 12.1 Unscrew the thumb screws from the bottom front of the chassis and remove the dust filter 12.2 Remove the fan dust filter by pressing down on the tab then pull out 12.3 Clean the dust filter using a clean cloth 13.Water Cooling Radiator Installation 13.1 To install an external water cooling system, use the pre-drilled holes located on the back to connect the tubes...
- Page 11 15.Front Connector Installation Guide Please refer to your motherboard user manual on the sections of “USB connector”And “audio connector”. Please verify the pin definition before connecting the connectors to the motherboard 1. USB and Audio connectors have foolproof design, can only be inserted in one direction 2.