Camera Setup - Samsung SMARTCAM SNH-E6440BN User Manual

Motion zone
Cancel Clear OK
1. Tap the motion zone icon.
2. Connect to the motion zone mode.
3. After touching the video, drag it to set the area.

You can set a max of three motion zones.
4. If you want to run the motion zone in the area set, tap
<OK>.

Motion is detected only in the set area.

Motion zone function only operates if motion detection is activated.
In <Setup> - <Event>, set motion detection.
5. To delete the set area, press <Clear> and <OK>.
If you want to exit the motion zone setting mode, tap
<Cancel>.
To control digital zooming
You can also zoom in by pinch open using two
fingers on the screen. To zoom out, pinch close
on the screen.
Touch and hold to drag the screen in any
direction to reveal the hidden part of the image
if enlarged bigger than the screen.

M
Current digital zooming level is noted next to the digital zoom box,
and digital zooming supports zooming up to x4.
Relay mode
If the network condition is not good and a connection is
unstable, then you can use the relay mode to view video for
seven minutes.
When the relay mode connection is made, the [
displayed on the video, and to maintain stable connections,
there will be no audio or HQ video.

J
If the router UPnP setting is not set, then a relay mode connection
can be made. Depending on the model of router used, a different
setting method is used. Refer to the user manual.

If a camera is connected to the multiple router, or the wired/wireless
network environments for camera and mobile device are unstable, a
relay mode connection can be made.

If you have trouble connection to the camera, visit "http://www.
samsungsmartcam.com", go to support page, and refer to
"Troubleshooting" on it.

5. Camera Setup

Tap the <Setup> icon to configure a camera to be monitored.
test Setup
test
General
Network
test
Time
Event
Live Event Playback Setup
SD Card
General setting
1. Tap <General>.
2. Configure the basic camera
settings.
] mark is
• Camera Name : Camera name
is used to easily identify the
camera when you have more
than one.
• Speaker/Mic : Adjust the
volume for the camera's built-in
mic or speaker.

M
If you set the mic to zero, there will be no
live sound and no audio event and also
there is no recording in the SD card.
• Audio REC : The voice can be
recorded or deleted by users.
• Night Vision : Set the IR lighting.
Check <Night Vision> to set
the camera to switch to the
night vision mode automatically.

M
In the case of SNH-1010N, you can
check <Night Vision> for a camera
to automatically operate the IR lighting
for two minutes depending on the
brightness of the neighboring areas.
• WDR : You can compensate for
the backlight by making a dark
area brighter, and a bright area
darker.

SNH-P6410BN supported
• Display date : Displays the date/
time on the live video.
• Save camera password : You
will be connected to your
camera without having to enter
the password.
• Change camera password :
Change the current camera
password.
General
Camera Name
test
Speaker
Mic
Audio REC
Night Vision
WDR
Display date
Save camera password
Change camera password
status LED
no o
Firmware Version Firmware Version v1.00 v1.00
Cancel Apply
Audio List
01. Add personalized audio clip
02. Add personalized audio clip
03. Add personalized audio clip
04. Add personalized audio clip
05. Add personalized audio clip
06. Add personalized audio clip
07. Add personalized audio clip
08. Add personalized audio clip
09. Add personalized audio clip
10. Add personalized audio clip
General General
Camera Name Camera Name test test
Speaker Speaker
M M Mic Mic
Current Password
Audio REC A Audio REC A
Night Vision N Night Vision N New Password
Use 1-8 numbers and/or letters
WDR WDR W W
Confirm password
Display date Display date D D
Show Password
S Save camera password S Save camera password
Cancel Apply
Change camera password C Change camera password C
status LED status LED
Firmware Version Firmware Version v1.00 v1.00
Cancel Cancel Apply Apply