Table of Contents
Advertisement
Wi-Fi Direct connection
M
You can only use it in a camera that has a Wi-Fi Direct sticker
attached to it.
Press the button, "Tap here to add registered camera" when you
register a camera being used in another account, in order to register
it immediately without setting it.
7.
Tap <Wireless Setup>.
Is there a WiFi DIRECT sticker on
If yes, select Wireless Setup.
If not, select Optional Setup.
Wireless
Setup
Tap here to add registered camera
8.
Tap <Next> after connecting
Registration
a camera according to the
instructions displayed on the
DCIN 5V
DCIN 5V
screen.
2
When the camera LED flashes in
red, press the WiFi button on the
back of the camera for 5 seconds.
9.
After selecting a camera to
connect, tap <Next>.
M
Select a camera that has the last
four digits of the serial number on
the back of the product.
the camera lens?
10.
Select a WiFi router connected to
your camera.
•
: After entering the
password, connect to a WiFi
router.
Optional
Setup
•
: Without the password, you
will not be connected to a WiFi
router.
• Other WiFi Networks : Enter the
SSID name, security type and
1
password.
Plug in the power adapter
and connect it to the
camera. Camera can take
If selected, it shows guide
up to 2 minutes to boot up.
on SSID and networking
procedures.
• Network password :
If you select a WiFi router with
the password, then the pop up
3
window will prompt you to enter
The status LED on the
camera will change to light
the password.
green/yellow. Tap <Next>
Next
11.
The LED of the camera will
Registration
turn into green if a camera is
The camera(s) will be listed below.
Select the camera you wish to add and
connected to Wi-Fi.
tap <Next>.
If a camera doesn't connect, please
check '?'.
M
Next
12.
Enter <Camera Name> and
Registration
<Camera password> and then
Select the WiFi network you
want the camera to connect to.
click <OK>.
Apple Network 8dfdc7
M
design
Cisco_WPS_57090
KT12580
NETGEAR27
Other WiFi Networks
13.
The camera registration is
Registration
Registration
completed.
Select the WiFi network you
Select the WiFi network you
want the camera to connect to.
want the camera to connect to.
Select <Yes> for a camera
Network password
setting.
Apple Network 8dfdc7
Apple Network 8dfdc7
Enter WiFi network password
Select <No> to view a live
design
design
screen.
Cancel
OK
Cisco_WPS_57090
Cisco_WPS_57090
M
KT12580
KT12580
NETGEAR27
NETGEAR27
1
2
3
4
5
6
7
8
9
0
q
w
e
r
t
y
u
i
o
p
a s d f g h
j
k
l
z x c v b n m
···
?
\
···
123
English(US)
.
Done
WIFI
(
)
Sym
Registration
Camera's LED will blink in blue
00 : 02
while searching for a WiFi router.
If a connection is made to the WiFi
router, the LED will be blue
Please wait until the status LED on the
consistently. After a short while,
camera changed from blue to green.
It takes about 3 minutes.
while the camera is connecting to
the server, the LED will turn green.
Registration
Registration
Create camera name and camera password.
Click <Show Password> to check
Camera Name
00 : 02
00 : 02
your password.
Example: Living Room
Camera password
Use 1 - 8 numbers and/or letters
Confirm password
Please wait until the status LED on the
Please wait until the status LED on the
camera changed from blue to green.
camera changed from blue to green.
It takes about 3 minutes.
It takes about 3 minutes.
Show Password
Cancel
Camera registered
successfully.
The camera settings can be set
If you failed to register wirelessly,
to your preference. Continue
with the camera setup?
please try again over a wireline.
Cameras may not be registered
depending on the settings of the
mobile device.
No
In this case, contact the service
center.
OK
Yes
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
