Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wincor Nixdorf TH210-3
Summary of Contents for Wincor Nixdorf TH210-3
- Page 1 TH210-3 for MF Thermal Printer User Guide...
- Page 2 Please send us a copy of this page if you have any constructive criticism. We would like to thank you in advance for your comments. With kind regards, Wincor Nixdorf International GmbH RD HWD 01 Rohrdamm 7; Haus 16 D-13629 Berlin Fax: +49 30 5017 3075 _____________________________________________________________________________...
- Page 3 Published by Wincor Nixdorf International GmbH D-33094 Paderborn...
- Page 4 TH210-3 for MF Thermal Printer User Guide Edition March 2010...
- Page 5 Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability; technical modifications possible. Copyright © Wincor Nixdorf International GmbH, 2010...
-
Page 6: Table Of Contents
Contents Manufacturer Certification Warranty General Safety Information Safety instructions Description of Printer Features Unpack the Printer Remove the Starter Paper Roll Supports Choose a location Connect the Cables Communication Cable Cash Drawer Cables Power Supply Cable Printer Controls Loading Receipt Paper To Load the Paper: Configuring the Printer Troubleshooting the Printer... - Page 7 Paper Specifications Print Zones Print Zones for 80 mm Paper List of Commands...
-
Page 8: Manufacturer Certification
For further information of the stipulation look at your contract. All parts of the product which are subject to wear and tear are not included in the warranty engagement. Please order spare parts at the Wincor Nixdorf customer service. _________________________________________________________... -
Page 9: General Safety Information
TH210-3 for MF _____________________________________________________________________ General Safety Information Before installing and using the printer, please read the following items carefully. Safety instructions Do not touch the cutter and tear bar of the printer. The print head is a thermal element and it is at high temperature during printing or just after operation, therefore please do not touch it and its peripherals for safety reasons. - Page 10 The printer should only be disassembled or repaired by a technician, who is certified by Wincor Nixdorf. At any work on the device and plugging/unplugging cables disconnect the device from the power supply completely. Switch off the device and pull the mains plug.
-
Page 11: Description Of Printer
TH210-3 for MF _____________________________________________________________________ Description of Printer The TH210 thermal receipt printer is extremely fast, quiet, and very reliable. With thermal printing technology, there is no ribbon cassette to change, and paper loading is extremely simple. The printer is small enough to fit almost anywhere and is easy to use with the receipt exiting from the top. -
Page 12: Features
TH210-3 for MF _____________________________________________________________________ Features Interfaces RS-232, 25pin Serial, only for fiscal countries Russia, Greece, Turkey and Hungary Memory/Firm 512K Flash Memory, History EEROM, 4K Buffer ware Resident PC Code Page 437 (US), PC Code Page 850 Character (Multilingual), PC Code Page 852; Code Pages Sets 737, 865, 858, 860, 863, 866, 874 and 1252. -
Page 13: Unpack The Printer
TH210-3 for MF _____________________________________________________________________ Unpack the Printer Save all packing materials for use if printer needs to be repacked. Check that all items listed were shipped Printer enclosed in a plastic bag with packing material Thermal starter paper roll (inside receipt bucket of printer) -
Page 14: Choose A Location
TH210-3 for MF _____________________________________________________________________ 1) Open the Rear Cover by pushing up on each side of the cover until it unsnaps. Remove the Test Printout. 2) Lift the Starter Paper Roll out of the paper bucket and slide the two Paper Roll Supports off. -
Page 15: Connect The Cables
TH210-3 for MF _____________________________________________________________________ Connect the Cables Caution: Connect the cables to the printer before plugging in the power supply. If power is received from the host computer, turn it off before connecting any cables. C o m m u n i c a t i o n... -
Page 16: Cash Drawer Cables
TH210-3 for MF _____________________________________________________________________ Cash Drawer Cables The Cash Drawer Cable connects the printer to one or two cash drawers. 1) Open Connector Cover at rear of printer if not previously open. 2) Plug the cable into the Cash Drawer Connector (standard phone jack) located at the rear of the printer (see illustration on previous page.) -
Page 17: Printer Controls
TH210-3 for MF _____________________________________________________________________ Printer Controls LED (Green) Paper Feed Button Reset Button Reset Button Should a paper jam or fault condition occur, press the Reset Button to reset the printer. The printer performs a startup routine, as if having been turned off, then on again. - Page 18 TH210-3 for MF _____________________________________________________________________ The green LED shows the printer status by shining or flashing. A continuous green (non-flashing) LED represents an “ON”, no-fault condition. Status Paper Is Low Flashes Slowly Paper Is Out Flashes Quickly Knife Jam Flashes Quickly then Slowly...
-
Page 19: Loading Receipt Paper
TH210-3 for MF _____________________________________________________________________ Loading Receipt Paper Change the paper when any of the following conditions occurs: Colored stripe appears on the receipt paper indicating the paper is low. Change the paper as soon as possible to avoid running out of paper part way through a transaction. -
Page 20: To Load The Paper
TH210-3 for MF _____________________________________________________________________ To Load the Paper: Open the Rear Cover by lifting up on each side of the cover until it unsnaps. Remove the used paper roll. Tear off the end of the new roll so that the edge is loose. - Page 21 TH210-3 for MF _____________________________________________________________________ Place the new roll into the paper bucket with a few inches of paper extending over the cabinet front (or top, if printer is mounted vertically). _________________________________________________________...
- Page 22 TH210-3 for MF _____________________________________________________________________ Caution The Paper must unroll from the bottom to ensure the printer will print and to prevent paper jamming. Close the cover. Pull the excess paper across the tear-off blade and remove. Advance the paper if necessary by pressing the Paper Feed Button.
-
Page 23: Configuring The Printer
TH210-3 for MF _____________________________________________________________________ Configuring the Printer The Configuration Menu allows the user to set general printer parameters. The test prints the settings for several functions, and partially cuts the paper between each variation. The printouts may vary for each model. The test ends with a partial cut of the paper, then begins again. - Page 24 TH210-3 for MF _____________________________________________________________________ The printer prints the Diagnostics Form and the Configuration Main Menu. Printer pauses and waits for Main Menu selection to be made (see sample printout on the next page.) 5. Continue through your menu selections until you are asked to: “Save New Parameters?”.
-
Page 25: Troubleshooting The Printer
TH210-3 for MF _____________________________________________________________________ Troubleshooting the Printer The printer is simple and generally trouble-free, but from time to time minor problems may occur. Follow these procedures to determine the cause and resolution of any problems the printer may be having. If the procedures in this section do not correct the problem, contact a service representative. -
Page 26: Printing Problems
TH210-3 for MF _____________________________________________________________________ Printing Problems Problem Possible What to Do Causes Colored stripe Paper is low. Change the on the receipt paper. Receipt does Paper is Open the not come out jammed. receipt cover, all the way inspect the... - Page 27 TH210-3 for MF _____________________________________________________________________ Print is light or Paper roll Check that the spotty loaded paper is incorrectly. loaded properly. Thermal printhead is recommended dirty. thermal receipt paper. Variations in Increase print paper. density in “Set Hardware Options” of printer...
-
Page 28: Printer Does Not Function
TH210-3 for MF _____________________________________________________________________ Printer Does Not Function Problem Possible What to Do Causes Printer does Printer not Check that not function plugged in. printer cables when turned are properly connected on both ends. Check that the host or power supply is getting power. -
Page 29: Characters
TH210-3 for MF _____________________________________________________________________ Characters Print Modes Available print modes: Standard Compressed Double High Double Wide Upside Down Rotated Underlined Bold Reverse Italic Scaled Size Characters sizes for the Standard and Compressed mode: Standard Characters per Inch: 15.6 Characters per Line: 44... -
Page 30: Compressed
TH210-3 for MF _____________________________________________________________________ Compressed Characters per Inch: 20.3 Characters per Line: 56 Cell Size: 10 x 24 Dots For more information about Programming the printer to “Programming print the various print modes. Guide” Paper Specifications The printer requires qualified thermal paper with the following... -
Page 31: Print Zones
TH210-3 for MF _____________________________________________________________________ Print Zones Print Zones for 80 mm Paper Specifications of print zone for 80 mm paper: 576 dots (addressable) @ 8 dots/mm, centered on 80 mm Standard Mode: minimum margins: 2.5 mm (.098 inches) Top margin to manual tear-off: 17.8 mm (0.70 inches) Top margin to knife cut: 19.0 mm (0.75 inches) -
Page 32: List Of Commands
TH210-3 for MF _____________________________________________________________________ List of Commands Commands control all operations and functions of the printer. This includes selecting the size and placement of characters and graphics on the receipt to feeding and cutting the paper. Details can be found in the... - Page 33 TH210-3 for MF _____________________________________________________________________ Code (Hexadecimal) Command 1B 07 Generate Tone 1B 0C Print Data in Page Mode 1B 12 Select 90 Degree Counter-Clockwise Rotated Print 1B 14 n Set Column 1B 16 n Select Pitch (Column Width) 1B 20 n...
- Page 34 TH210-3 for MF _____________________________________________________________________ Code (Hexadecimal) Command 1B 4A n Print and Feed Paper 1B 4B n1 n2 d1...dn Select Single-Density Graphics 1B 4C Select Page Mode 1B 52 n Select International Character Set 1B 53 Select Standard Mode 1B 54 n...
- Page 35 TH210-3 for MF _____________________________________________________________________ Code (Hexadecimal) Command 1D 03 n Real Time Request to Printer (GS Sequence) 1D 04 n Real Time Status Transmission (GS Sequence) 1D 05 Real Time Printer Status Transmission 1D 06 Get Firmware CRC 1D 07...
- Page 36 TH210-3 for MF _____________________________________________________________________ Code (Hexadecimal) Command 1D 62 n Select or Cancel Smoothing Mode 1D 66 n Select Pitch of HRI Characters 1D 68 n Select Bar Code Height 1D 6B m d1...dk 00 Print Bar Code 1D 6B m n d1...dn...
Need help?
Do you have a question about the TH210-3 and is the answer not in the manual?
Questions and answers