Precautions On Adjusting - Sony DCR-DVD100 Service Manual

2-1-2.

Precautions on Adjusting

Note1: Before performing the adjustments, check the data of page: 0,
address: 10 is "00". If not, set data: 00 to this address.
1) The adjustments of this unit are performed in the PLAY mode
or MOVIE mode.
To set to the PLAY mode, set the mode dial to "PLAY/EDIT"
( ) or set the "Forced PLAY mode" using the adjusting
remote commander (Note2).
To set to the MOVIE mode, set the mode dial to "MOVIE"
( ) or set the "Forced MOVIE mode" using the adjusting
remote commander (Note3).
After completing adjustments, be sure to exit the "Forced
MOVIE Mode" or "Forced Camera Power ON Mode". (Note5)
2) The front panel block (Microphones, MA-420 board (S VIDEO
jack, remote commander receiver, infrared LED, angular
velocity sensors)) need not be connected except for the case
that the S VIDEO jack is used. To remove it, disconnect the
following connector.
MA-420 board CN5503 (22P, 0.5mm)
3) Cabinet (R) (CK-127 board, LCD block) need not be connected.
But removing the cabinet (R) (disconnecting the VC-307 board
CN1007) means removing the lithium 3V power supply (CK-
127 board, BT5201), data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
But, the self-diagnosis data and the data on history of use (user
initial power on date, final condensation occurrence data) will
be kept even if the cabinet (R) has been removed. (Refer to "6-
3.Service Mode" for the data on the history use and the self-
diagnosis data.)
To remove the cabinet (R), disconnect the following connectors.
VC-307 board CN1007 (39P, 0.3mm)
4) The EVF block (LB-084 board) need not be connected. To
remove it, disconnect the following connector.
VC-307 board CN2201 (20P, 0.5mm)
5) The intelligent accessory shoe need not be connected. To
remove it, disconnect the following connector.
VC-307 board CN1001 (10P, 0.5mm)
6) The lens block (CD-428 board) need not be connected. To
remove it, disconnect the following connectors.
VC-307 board CN1301 (24P, 0.5mm)
VC-307 board CN1201 (24P, 0.5mm)
VC-307 board CN1010 (2P, 0.8mm)
7) By setting the "Forced PLAY mode" or the "Forced MOVIE
mode", the video section can be operate even if the control
switch block (PS-CX5500) has been removed. When removing
it, disconnect the following connector.
VC-307 board CN1002 (14P, 0.5mm)
8) To open the VC-307 board, use the following extension cable
between the VC-307 board CN1008 and MD-097 board
CN4901.
J-6082-352-A (100P, 0.5mm)
Note2: Setting the "Forced PLAY mode" (PLAY/EDIT mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the power to be turned on with the
control switch block (PS-CX5500 block) removed.
After completing adjustments, be sure to exit the "Forced PLAY
mode".
Note3: Setting the "Forced MOVIE mode"
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the power to be turned on with the
control switch block (PS-CX5500 block) removed.
After completing adjustments, be sure to exit the "Forced MOVIE
mode".
Note4: Setting the "Forced STILL mode"
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the memory power to be turned on
with the control switch block (PS-CX5500 block) removed.
After completing adjustments, be sure to exit the "Forced STILL
mode".
Note5: Exiting the "Forced mode"
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 0, address: 01, and set data: 00.
6-37
DCR-DVD/100DVD100E