Heatilator Icon I100 Owner's Manual
Woodburning fireplace
Hide thumbs
Also See for Icon I100:
- Installation manual (45 pages) ,
- Owner's manual (24 pages) ,
- Dimension manual (2 pages)
Table of Contents
Advertisement
Quick Links
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with questions on installation, operation, or service.
NOTICE:
DO NOT discard this manual!
Model(s):
WOODBURNING FIREPLACE
Installation and service of this fi replace should be
performed by qualifi ed personnel. Hearth & Home
Technologies recommends NFI certifi ed profes-
sionals, or technicians supervised by an
NFI certifi ed professional.
Owner's Manual
Operation and Care
Heatilator • ICON I100 Owner's Manual • 4013-264 • Rev E • 11/25/13
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• DO NOT overfi re. Overfi ring will void your
warranty.
• Comply with all minimum clearances to com-
bustibles as specifi ed. Failure to comply may
cause house fi re.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
WARNING
Fire Risk.
For use with solid wood fuel only.
Other fuels may overfi re and generate
poisonous gases (i.e. carbon monoxide).
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Heatilator Icon I100
Summary of Contents for Heatilator Icon I100
-
Page 1: Woodburning Fireplace
High temperatures may ignite clothing or other fl ammable materials. WOODBURNING FIREPLACE • Keep clothing, furniture, draperies and other fl ammable materials away. WARNING Installation and service of this fi replace should be performed by qualifi ed personnel. Hearth & Home Technologies recommends NFI certifi ed profes- Fire Risk. sionals, or technicians supervised by an For use with solid wood fuel only. NFI certifi ed professional. Other fuels may overfi re and generate poisonous gases (i.e. carbon monoxide). Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 2: Table Of Contents
8. Chimney Fire B. General Operating Parts 1. Flue Damper 2. Outside Air 3. Glass Doors C. Fuel 1. Hardwood vs. Softwood 2. Moisture content 3. Seasoning 4. Storing Wood 5. Burning Process 6. Creosote Formation 7. Processed Solid Fuel Firelogs D. First Fire E. Lighting Instructions Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 3: Welcome
IF INSTALLATION OR OPERATING INSTRUCTIONS ARE MISSING DECORATIVE GAS APPLIANCE IN THE FIREPLACE, CONTACT: HEARTH & HOME TECHNOLOGIES, ADJUST DAMPER TO THE FULLY OPEN POSITION. 7571 215th Street West, Lakeville, MN 55044 Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 4: Limited Lifetime Warranty
2 years Factory-installed blowers Molded refractory panels 3 years Firepots and burnpots 5 years 1 year Castings and baffles Manifold tubes, 7 years 3 years HHT chimney and termination 1 year Burners, logs and refractory years Limited 3 years Firebox and heat exchanger Lifetime All replacement parts 90 Days beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645F 02-18-13 Page 1 of 2 Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... - Page 5 This warranty is void if: • The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes. • The appliance is subjected to prolonged periods of dampness or condensation. • There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation. LIMITATIONS OF LIABILITY: • The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. 4021-645F 02-18-13 Page 2 of 2 Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13...
-
Page 6: Product Specific And General Information
• DO NOT install unvented gas logs. the optional components specified in this manual. These • Damper must be locked open. optional components may be purchased separately and • Gas flame may generate fumes. installed at a later date. An outside air kit, gas log set, gas insert or gas log-lighter should be installed at the time of fireplace installation. Heatilator is a registered trademark of Hearth & Home Technologies. Warning! Risk of Fire! For use with solid wood fuel only. Other fuels may overfire and generate poisonous gases (i.e. carbon monoxide). Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 7: Important Safety And Operating Information
Front of Fireplace Front of Fireplace Clear Space Clear Space Sides of Fireplace Sides of Fireplace (from the FP (from the FP (from the FP (from the FP (from the FP opening) opening) opening) opening) opening) Figure 3.1 Clear Space Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 8: Grate
If doors are left partly open, gas and flame may be drawn out of the freplace opening. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 9: General Operating Parts
B. General Operating Parts WARNING! DO NOT operate fi replace before reading and understanding operating instructions. Failure to operate fi re- place according to operating instructions could cause fi re or injury. Flue Damper Outside Air Control Section 2.I. Section 2.F. UP to Open UP to Open DOWN to Close DOWN to Close Figure 3.2 General Operating Parts Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 10: Flue Damper
Close the inlet to prevent cold drafts when the fi replace is not being used CAUTION! Outside air control handle may be warm. Adjust before lighting fi re. 3. Glass Doors • Glass doors are optional. • Refer to Figure 3.3 for how to properly use them. FULLY OPEN PARTLY OPEN CORRECT INCORRECT FULLY CLOSED PARTLY CLOSED CORRECT INCORRECT Figure 3.3 Operating Positions of Bi-fold Doors Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 11: Fuel
Soft woods Hard woods • Douglas Fir • Oak • Pine • Maple • Spruce • Apple • Cedar • Birch • Poplar • Aspen • Alder Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 12: Seasoning
D. First Fire • Store wood under cover, such as in a shed, or Before lighting your first fire in the fireplace, make certain covered with a tarp, plastic, tar paper, sheets of scrap that: plywood, etc., as uncovered wood can absorb water from rain or snow, delaying the seasoning process. • refractory is in place Avoid covering the sides and ends completely. Doing • all labels have been removed so may trap moisture from the ground and impede air circulation. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 13: Lighting Instructions
WARNING! Risk of Fire! Keep combustible materials, gasoline and other flammable vapors and liquids clear of the fireplace. DO NOT: • store flammable materials close to the fireplace • use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 14: Maintenance And Service
• Confirm that termination cap remains clear and unobstructed. • Inspect for blockages such as bird nests, leaves, etc. • Inspect for corrosion or separation. • Inspect for creosote and remove as needed, at least every two months during the heating season. • Inspect the system at the fireplace connection and at the chimney top. In the event of a chimney fire, Hearth & Home Tech- nologies recommends replacement of the chimney and inspection of the adjacent structure to the provisions of NFPA Level III inspection criteria. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 15: Grate
• Clean glass with a non-abrasive glass cleaner. Use a thoroughly cooled. damp cloth dipped in wood ashes or a commercially available oven cleaner. Remove any oven cleaner F. Refractory residue with a glass cleaner or soap and water. Frequency: Tools Needed: • Inspect condition of refractory. Replace if crumbly or otherwise deteriorated, or if cracks exceed 1/4 in. (6 mm). Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 16: Troubleshooting
Wood condition is too wet, too large Use dry, seasoned wood (refer to wood fuel section). Bed of coals not established before Start with paper & kindling to establish bed of coals (refer adding wood to starting fire section). Flue blockage such as birds’ nests Have chimney inspected for creosote and cleaned by a or leaves in termination cap certified chimney sweep. Down draft or negative pressure Do not use exhaust fans during start-up (refer to negative Competition with exhaust devices pressure section). Open window below the fireplace towards the wind. Fire burns too fast Extremely dry or soft wood Mix in hardwood. Mix in less seasoned wood after fire is established (refer to wood fuel section). No glass doors Add glass doors to slow down air flow. Overdrafting Check for correct vent height; too much vertical height creates overdrafting. Check location of vent termination (refer to chimney assembly section). Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... -
Page 17: Faqs
If the fire is hard to start and smoke spills out of the fire- place, or you find it difficult to establish and maintain a Contact your dealer for additional informa- moderately high burn rate, then the flue draft is too low tion regarding operation and troubleshoot- and corrective measures must be taken. ing. Visit www.heatilator.com to find a dealer. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... - Page 18 (furnace, fan, Unsealed dryer, etc.)? can lights? Overhead fan operating? Creosote buildup in flue? Air register from furnace near fireplace? Doors opening and closing? Outside air Window closed Combustion closed? for start-up? air control Figure 5.1 Factory-built Fireplaces: Troubleshooting Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13...
-
Page 19: Reference Materials
10002 Heat Shield 34568 Nailing Flange Qty 6 req 31190 Outside Air Kit Qty 2 req 35191 Fastener Pack 4025-023 Outside Air Shield 33271 4 in. Outside Air Inlet Ring 35192 Screen Cover (top only) Qty 2 req 34548 Smoke Shield Kit 4013-188 Strip Protector Qty 3 req 18320 Touch-Up Paint 71479 Additionals service parts on following page. 8/13 Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... - Page 20 Brick Refractory - Left Side-2 Color Post AK931849 4013-230 Pre AK931849 4013-198 Brick Refractory - Right Side- 3 color No longer available Brick Refractory - Right Side-2 Color Post AK931849 4013-229 Refractory Retainer Kit 34584 Refractory Retainer 3 ea. 11847 Grate Retainer 2 ea. 4017-060 Owner’s Manual 4013-264 Installation Manual 4013-263 Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13...
-
Page 21: Accessories
Grand Vista Cabinet Style Mesh Doors, black or bronze Contour Cabinet Style Mesh Doors, black or bronze GV100BK CONTOUR100BK GV100BZ CONTOUR100BZ Gas Inserts Gas Log Sets Gas Log Lighters Wood-burning Inserts Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13... - Page 22 This page intentionally left blank. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13...
- Page 23 This page intentionally left blank. Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13...
-
Page 24: Contact Information
6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884,7047962, 7216645, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2012 Heatilator • ICON I100 Owner’s Manual • 4013-264 • Rev E • 11/25/13...
Need help?
Do you have a question about the Icon I100 and is the answer not in the manual?
Questions and answers