Cisco PrecisionHD 1080p 12X User Manual page 24

Cisco TelePresence PrecisionHD Camera
Contents Introduction
The VISCA™/RS–232 control protocol, cont...
Inquiries
Command Command
Packet
CAM_ID_Inq 8x 09 04 22 ff
CAM_SWID_Inq 8x 09 04 23 ff
CAM_HWID_Inq 8x 09 04 24 ff
Zoom_Pos_Inq 8x 09 04 47 ff
Focus_Pos_Inq 8x 09 04 48 ff
Focus_Mode_Inq 8x 09 04 38 ff
PanTilt_Pos_Inq 8x 09 06 12 ff
Power_Inq 8x 09 04 00 ff
WB_Mode_Inq 8x 09 04 35 ff
WB_Table_Inq 8x 09 04 75 ff
AE_Mode_Inq 8x 09 04 39 ff
Backlight_Mode_ 8x 09 04 33 ff
Inq
Mirror_Inq 8x 09 04 61 ff
Flip_Inq 8x 09 04 66 ff
D14640.04 PrecisionHD 1080p-720p Camera User Guide
© 2010-2011 Cisco Systems, Inc. All rights reserved.
The physical interface
Response
Resp: 90 50 zz xx 00 yy ff
Only zz, which identifies the camera, is
relevant. zz = 0x50 for this camera.
Resp: y0 50 [1-125 bytes ASCII SWID] ff. Never
route this message through Sony cameras.
The response is the Module Serial Number
stored in EEPROM. The number is converted
to ASCII : y0 50 [12 bytes ASCII HWID] ff.
Resp: y0 50 0p 0q 0r 0s ff
pqrs: zoom position
Resp: y0 50 0p 0q 0r 0s ff
pqrs: focus position
Resp: y0 50 0p ff
p=2: Auto, p=3: Manual
Resp: y0 50 0p 0q 0r 0s 0t 0u 0v 0w ff
pqrs: pan position tuvw:
tilt position
Resp: y0 50 0p ff
p=2: On, p=3: Off
Resp: y0 50 0p ff
p=0: Auto , p=6: Table manual
Resp: y0 50 0p 0q 0r 0s ff
pqrs: Table used if table mode
Resp: y0 50 0p ff
p=0: Auto, p=3: Manual
Resp: y0 50 0p ff
p=2: On, p=3: Off
Resp: y0 50 0p ff
p=2: On, p=3: Off
Is video flipped or not?
Resp: y0 50 0p ff
p=2: On , p=3: Off
, July 2011
.
Connecting the camera Video output formats
INFO: Some VISCA™ commands do not apply to the PrecisionHD 1080p 4X camera.
Command
Gamma_Mode_Inq
Gamma_Table_Inq
Call_LED_Inq
Power_LED_Inq
Video_System_Inq
DIP_Switch_Inq *
IR_Output_Inq
ALS_RGain_Inq *
ALS_BGain_Inq *
ALS_GGain_Inq *
ALS_WGain_Inq *
Up side down_Inq
*
*
Do not apply to PrecisionHD 4X camera
24
PrecisionHD Camera User guide
Daisy chaning
Command
Packet
8x 09 04 51 ff Resp: y0 50 0p ff
p=2: Auto, p=3: Manual
8x 09 04 52 ff Resp: y0 50 0p 0q 0r 0s ff
pqrs: Gamma table in use if manual mode.
8x 09 01 33 01 ff Resp: y0 50 0p ff
p=2: On, p=3: Off, p=4: Blink
8x 09 01 33 02 ff Resp: y0 50 0p ff
p=2: On, p=3: Off
8x 09 06 23 ff y0 50 0p 0q 0r 0s ff
pqrs=video mode currently being output on
the HDMI port. See chapter on DIP switches.
8x 09 06 24 ff y0 50 0p 0q 0r 0s ff pqrs contains the bit
pattern of the DIP switch. See chapter on
DIP switches.
8x 09 06 08 ff Resp: y0 50 0p ff
p=2: On, p=3: Off
8x 09 50 50 ff Ambient Light Sensor Resp: y0 50 0p 0q 0r
0s 0t 0u 0v 0w ff
pqrstuv=32 bit unsigned integer, relative gain
value. The integration time is a constant set in
the camera SW.
8x 09 50 51 ff
8x 09 50 52 ff
8x 09 50 53 ff
8x 09 50 70 ff Resp: y0 50 0p ff
p=0: Camera is upright.
p=1: Camera is upside down.
Appendices Appendices
Response
www.cisco.com