Robe Stage Faze 1500AT User Manual
  1. Manuals
  2. Brands
  3. Robe Manuals
  4. Lighting Equipment
  5. Stage Faze 1500AT
  6. User manual
Robe Stage Faze 1500AT User Manual

Robe Stage Faze 1500AT User Manual

At series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Version 1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stage Faze 1500AT and is the answer not in the manual?

Questions and answers

Related Manuals for Robe Stage Faze 1500AT

Summary of Contents for Robe Stage Faze 1500AT

  • Page 1 Version 1.1...

  • Page 2: Table Of Contents

    StageFaze 1500 AT Table of contents 1.Introduction........................3 2.Cautions ........................... 3 3.Unpacking & Inspection....................4 4.Description of the device....................4 5. Fluid ..........................5 5.1 General notes ............................5 5.2 Filling the fluid tank............................5 6. Operatting the StageFaze 1500 AT ................5 6.1 Selecting a location ...........................5 6.2 Putting into operation ..........................6 6.2 Switching the StageFaze 1500 AT off.......................6...

  • Page 3: Introduction

    1.Introduction Thank you for choosing an ROBE StageFaze 1500 AT. You now own a rugged and powerful state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ROBE Stage Faze 1500 AT machine for years to come.

  • Page 4: Unpacking & Inspection

    Before beginning initial setup of your ROBE Faze machine, make sure that there is no evident damage caused by transportation. In the event that the unit's housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ROBE distributor for assistance.

  • Page 5: Fluid

    5.1 General notes The ready-to-use StageFaze 1500 AT fluid for use in this device is available from your local ROBE distributor. To guarantee trouble-free operation the special “StageFaze 1500 AT“ must be used. Use of other liquids will void the manufacturer‘s warranty and can be dangerous to your health.

  • Page 6: Putting Into Operation

    6.2 Putting into operation Warning: Never connect the StageFaze 1500 AT to a dimmer or switchpack! This may destroy the machine. Connect the power plug to the mains supply. Make sure the correct voltage is selected.Switch on the power switch (10). A P and two figures appear on the LED display e.g.: After 60 Seconds, the StageFaze 1500 AT is heated up.

  • Page 7: Stand Alone

    6.4 Operating via DMX 512 Connecting the StageFaze 1500 AT to a DMX desk, use the 3XLR sockets [12], at the rear side of the fixture. As soon as the machine receives a correct DMX signal, the yellow DMX LED will be lit. Please note: The StageFaze 1500 AT uses two channels on your DMX desk! First Channel = Pump, second Channel =Fan Adjusting the DMX start address 1) Press the Mode-button [14] at the control panel until three figures appear on the LED-display [17] (see Fig.
  • Page 8 2) Press the Enter button once to switch to the HDCS Menu. The red Timer/Profile-LED will be lit. 3) Adjust settings 1 to 7 according to the chart below, using the Up/Down buttons and pressing the Mode button to switch between the settings.

  • Page 9: Cleaning,Care And Maintenance

    Auto start If the timer is in operation and you disconnect the machine from the mains cable, the StageFaze 1500 AT will re-start in the Timer-Mode as soon as it‘s reconnected to the mains. To stop this press the Mode-button for more than 2 seconds or by switching to „ESC“ in the Timer-Mode and then press the Enter-button.

Table of Contents