Section 2: Unpacking; Section 3: Getting To Know Your Blender; Section 4 - Installation & Operational Overview; Professional 750 - Blendtec PROFESSIONAL 800 Owner's Manual And User's Manual

SECTION 2: UNPACKING

SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE
2.1 UNPACKING YOUR BLENDER
You should have received the following items:
• Professional series blender motor base
• Blender jar with lid
Additional literature may be included depending on package configuration�
1� Remove blender motor base, blender jar and lid from packaging�
2� Unwind the power cord�
3� Check for any packing material that may have blocked ventilation holes on the
underside of the blender motor base�
4� Inspect all items to ensure no damage occurred during shipment�
5� If any damage has occurred, contact Blendtec customer service (see page 17)
immediately�
2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE
Record your blender motor serial number and date of purchase in the space below�
You will need these when contacting Blendtec for service or questions�
Motor Serial #(Found on bottom of motor base):_________________________
Date of Purchase: ______________________________________________
Purchased From: _______________________________________________
2.3 REGISTERING YOUR BLENDER
Register online at www�blendtec�com/registration

SECTION 3: GETTING TO KNOW YOUR BLENDER

(Refer to Figures 1 and 2 on Page 6)
3.1 BLENDER MOTOR BASE
• Smart Touch Interface: The interface consists of one-touch pre programmed
cycles and speeds, as well as Stop and Pulse buttons�
• Hardened Metal Drive Socket: This is where the jar couples with the motor to turn
the blade assembly� It is made of hardened metal�
• LCD Information Center: This displays how many blend cycles your blender has
run, remaining time during blends, and any error messages�
• Power Unit: This unit is located within the blender motor base and contains the
computerized electronics that run the blender�
• Motor Base Cover: This durable plastic material houses the power unit�
• Power Cord: The power cord is located at the back of the motor base cover�
4
3.2 BLENDER JAR ASSEMBLY
The blender jar assembly consists of the blender jar, blade assembly, and lid�
• Jar: The jar is durable, BPA-free, and easy to clean�
• Blade Assembly: The uniquely designed stainless steel blade provides fast,
consistent blending�
• Lid: The lid seals liquids within the jar during blending�
NOTE: Filling the blender jar beyond the marked capacity is not recommended.
SECTION 4:
INSTALLATION & OPERATIONAL OVERVIEW

4.1 PROFESSIONAL 750™

4.1.1 INSTALLATION
Above Counter Installation
1� Place the blender on a flat, clean, and dry surface� Blender vents should be
unobstructed to allow proper cooling during use�
2� Make sure an outlet is available within two feet of the blender motor�
3� Place appropriately filled blender jar, with lid in place, onto blender base�
4� We recommend that surge protection be placed between the receptacle and
the blender motor on the circuit connected to the blender motor�
Preparation for In-Counter Installation
1� Identify the best place to install your blender� Consider proximity to ingredients,
available counter space, and access to a power outlet�
2� Ensure that the location meets all dimensional requirements (see Figure 3)�
a� The countertop must be no thicker than 1 1/4 inch (32 mm) to ensure
adequate ventilation�
NOTE: Ensure sufficient air circulation beneath the blender base. Hot air should
not be trapped beneath the counter top. Nothing should be stored within 3 inches
(76 mm) of the bottom of the motor.
3� Cut a hole in the counter top 4 ⅜ inches (111 mm) wide and 5 ⅞ inches (149
mm) long with the shorter side facing the operator (See Countertop Hole
Template or Figure 3)� Make sure all space requirements and measurements are
correct BEFORE cutting� It is recommended that you consult with a professional
before cutting�
In-Counter Installation
1� Remove the motor base from the motor base cover�
2� Slide the blender base into the new hole in your countertop, the LCD indicator
and touchpad facing the operator side of the blender� The rubber gasket on the
rim of the motor base should fit into the hole and rest lightly on the countertop�
3� Make sure the power switch is off� Plug the unit into a 120 volt outlet with
15 amp protection�
5