Section 2: Unpacking; Section 3: Getting To Know Your Blender - Blendtec CLASSIC SERIES Owner's Manual And User's Manual

1.8 WARNING, DO NOT BLEND HOT LIQUIDS OR OTHER
HOT INGREDIENTS
Starting blend cycles with boiling or very hot liquids or other hot ingredients may
result in burns or cause the lid to blow off�
1.9 USE CAUTION WHEN BLENDING ON THE HOT SOUP CYCLE
When blending on the Hot Soup cycle, blade friction will heat the contents�
The vented lid releases pressure� Be careful not to come in contact with any
steam coming from the clear centre part of the lid�
1.10 POWER CORD PRECAUTIONS
• NEVER operate the blender with a damaged cord or plug� If the cord is
damaged, it must be replaced by the manufacturer or an authorized service
agent to avoid a hazard�
• DO NOT permit the cord to hang over the edge of the work surface�
• NEVER use an extension cord with the unit�
• Unplug the blender motor when not in use and before moving the blender or
cleaning it�
1.11 NEVER ATTEMPT TO REPAIR THE POWER UNIT
Never remove the blender motor base cover� The blender motor does not
contain user-adjustable or serviceable parts� A qualified service agent must make
all service adjustments� Removing the cover or attempting to service the blender
will void the warranty�
1.12 TURN THE POWER SWITCH OFF WHEN NOT IN USE
The power switch (ON/OFF switch) is located on the back of the blender motor
base cover�
1.13 AVOID TOUCHING THE BLENDER DRIVE SOCKET OR JAR
SHAFT AFTER USE!
The blender drive socket and jar shaft may become very hot during blend cycles�
1.14 SAFETY
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they are supervised or have been given instructions on
how to use the appliance by a person responsible for their safety� Children
should be supervised to ensure that they do not play with the appliance�
1.15 THIS BLENDER IS INTENDED FOR HOME USE ONLY! ANY
USE OF THIS BLENDER FOR COMMERCIAL PURPOSES
VOIDS ALL WARRANTIES
1.16 NEVER OPERATE THE BLENDER WHEN IT IS FILLED
BEYOND THE MARKED CAPACITY OF THE JAR
SAVE THESE INSTRUCTIONS
2

SECTION 2: UNPACKING

SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE
2.1 UNPACKING YOUR BLENDER
You should have received the following items:
• Classic series motor base
• Blender jar with blade assembly and lid
Additional literature may be included depending on package configuration�
1� Remove the blender motor base, the blender jar with the blade assembly, and the
lid from the packaging�
2� Unwind the power cord�
3� Check for any packing material that may be blocking the ventilation holes on the
underside of the blender motor base�
4� Inspect all items to ensure no damage occurred during shipment�
5� If any damage has occurred, contact your Blendtec service agent immediately�
2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE
Record your blender motor serial number and the date of purchase in the space
below�
You will need these when contacting Blendtec for service or with questions
Motor Serial # (found on the bottom of the motor base):
___________________________________________________________
Date of Purchase: ______________________________________________
Purchased From: _______________________________________________
2.3 REGISTERING YOUR BLENDER
Register your blender online at www�blendtec�com/registration�

SECTION 3: GETTING TO KNOW YOUR BLENDER

(Refer to Figures 1 and 2)
3.1 BLENDER MOTOR BASE
• Touchpad: Consists of one-touch pre-programmed cycles and speeds, as well as
Stop and Pulse buttons�
• Hardened Metal Drive Socket: Where the jar couples with the motor to turn the
blade assembly; made of hardened metal�
• LCD Information Centre: Displays the number of times a blend cycle button has
been pressed�
• Power Unit: This unit is located within the blender motor base and contains the
computerized electronics that run the blender�
• Motor Base Cover: Houses the power unit in a durable, plastic material�
• Power Switch: Located in the lower-right corner on the back of the motor base cover�
• Power Cord: Located at the back of the motor base cover�
3