Section 2: Unpacking; Section 3: Getting To Know Your Blender - Blendtec designer series Owner's Manual And User's Manual

1.8 WARNING, DO NOT BLEND HOT LIQUIDS OR OTHER
HOT INGREDIENTS
Starting blend cycles with boiling or very hot liquids may result in burns or cause
the lid to blow off�
1.9 USE CAUTION WHEN BLENDING ON THE HOT SOUP CYCLE
When blending on the Hot Soup cycle, the friction of the blade will heat the
contents� The vented lid will allow pressure relief� Be careful not to come in contact
with any steam coming from the clear centre lid�
1.10 POWER CORD PRECAUTIONS
• NEVER operate with a damaged cord or plug� If the supply cord is damaged, it
must be replaced by the manufacturer or an authorised service agent to avoid a
hazard�
• DO NOT permit the cord to hang over the edge of the work surface�
• NEVER use an extension cord with the unit�
• Unplug the blender motor when not in use, before changing blender locations or
when cleaning�
1.11 NEVER ATTEMPT TO REPAIR THE POWER UNIT
Never remove the blender motor cover� The blender motor does not contain user-
adjustable or serviceable parts� A qualified service agent must make all service
adjustments� Removing the cover or attempting to service the blender will void
the warranty�
1.12 TURN THE BLENDER OFF WHEN NOT IN USE
1.13 AVOID TOUCHING THE BLENDER DRIVE SOCKET OR JAR
SHAFT AFTER USE!
The blender drive socket and jar shaft may become very hot after blend cycles�
1.14 SAFETY
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety� Children should be supervised
to ensure that they do not play with the appliance�
1.15 THESE BLENDERS ARE INTENDED FOR HOME USE ONLY!
ANY USE OF THE DESIGNER SERIES BLENDER FOR
COMMERCIAL PURPOSES VOIDS ALL WARRANTIES
1.16 NEVER OPERATE THE BLENDER WITH MORE THAN THE
MARKED CAPACITY OF THE JAR
SAVE THESE INSTRUCTIONS
2

SECTION 2: UNPACKING

SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE
2.1 UNPACKING YOUR BLENDER
You should have received the following items:
• Designer series blender motor base
• Blender jar with lid
• Blendtec 101 booklet
• Customer Service And Warranty Registration Card
Additional literature may be included depending on package configuration
1� Remove blender motor base, blender jar and lid from packaging�
2� Unwind the power cord�
3� Check for any packing material that may have blocked ventilation holes on the
underside of the blender motor base�
4� Inspect all items to ensure no damage occurred during shipment�
5� If any damage has occurred, contact your Blendtec service agent immediately�
2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF
PURCHASE
Record your blender motor serial number and date of purchase in the space
below� You will need these when contacting Blendtec for service or questions�
Motor Serial No� (Found on bottom of motor base):_____________________
Date Of Purchase: ____________________________________________
Purchased From: _____________________________________________
2.3 REGISTRATION OF YOUR BLENDER
Register online at www�blendtec�com/registration

SECTION 3: GETTING TO KNOW YOUR BLENDER

(Refer to Figures 1 and 2)
3.1 BLENDER
MOTOR BASE
• Smart Touch Interface: Consists of pre-programmed cycles, capacitive touch
slider and various one-touch settings, depending on the model�
• Hardened Metal Drive Socket: Where the jar couples with the motor to turn the
blade assembly; made of hardened metal�
• LED Information Centre: Displays the number of times a blend cycle button has
been pressed, the time left to blend and error messages�
• Power Unit: This unit is located within the blender motor base and contains the
computerised electronics that run the blender�
• Motor Base Cover: Houses the power unit in a durable, plastic material�
• Power Cord: Located at the back of the motor base cover�
3