Keys Fitness KF-1560 Owner's Manual
  1. Manuals
  2. Brands
  3. Keys Fitness Manuals
  4. Home Gym
  5. KF-1560
  6. Owner's manual

Keys Fitness KF-1560 Owner's Manual

Keys fitness home gym owner's manual
Hide thumbs

Advertisement

Table of Contents

KF-1560
Owner's Manual
215-00113
10/06 Rev A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KF-1560 and is the answer not in the manual?

Questions and answers

Related Manuals for Keys Fitness KF-1560

Summary of Contents for Keys Fitness KF-1560

  • Page 1 KF-1560 Owner’s Manual 215-00113 10/06 Rev A...

  • Page 2: Table Of Contents

    Table of Contents Before You Start Important Safety Information Assembly Weight Ratios Weight Stack Sticker Placement Cable View Top View Exploded View Parts List Warranty Information 5-21...

  • Page 3: Before You Start

    This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please contact us at our Keys Fitness Help line. We have trained service technicians on site to take care of you, our valued customer.

  • Page 4: Important Safety Information

    • This unit should only be used on a level surface and is intended for indoor use only. Keys Fitness recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning.

  • Page 5: Assembly

    Assembly Box 1...
  • Page 6 Assembly Box 2...
  • Page 7 Assembly Box 3 101# Box 5 Box 4 100# Box 6...
  • Page 8 Assembly Step 1 Insert the two Guide Rods (14) into Rear Base (3) and secure them in place using two Washers (91), two Spring Washers (89), and two Allen Bolts (86). Figure 1...
  • Page 9 Assembly Step 2 Slide Seat Pad Support Receptacle (1) onto Rear Base (3) and secure in place using three Nylon Locknuts (93), six Washers (91), and three Bolts (80). Connect Front Upright (5) onto Seat Pad Support Receptacle (1) and secure together using two Nylon Locknuts (93), four Washers (91), and two Bolts (79).
  • Page 10 Assembly Step 3 Install the Main Upright (2) onto the Seat Pad Support Receptacle (1). Secure it in place using three Nylon Locknuts (93), six Washers (91), and three Bolts (80) on the side. Two Bolts (87), one Spring Washers (88), three Washers (90), one Nylon Locknut (92) will secure it at the bottom.
  • Page 11 Assembly Step 4 Slide one Weight Stack Bumper (62) down each Guide Rod (14). Next, slide the weight plates down the Guide Rods (14) in this order - five 15lb Plates (15), nine 10lb Plates (16), five 5lb Plates (17), and the Top Plate (18). For more information see Weight Stack Placement (pg 23). Insert the Main Top Beam (4) onto the two Guide Rods (14) and the Main Upright (2).
  • Page 12 Assembly Step 5 Attach Press Arm Support (6) to Main Upright (2) by aligning the holes and sliding the Shaft (19) through. Secure the Shaft (19) in place using two Set Screws (50). Install Press Arm (7) to Press Arm Support (6) by aligning the holes and sliding the Shaft (21) through.
  • Page 13 Assembly Step 6 Slide Long Foam Tube (11) into the hole towards the lower part of the Main Upright (2). Slide the Shaft (44) into top of the Leg Extension Lever (8). Attach Leg Extension Lever (8) to Seat Pad Support Receptacle (1) and secure using one Washer (46), one Spring Washer (47), and one Allen Bolt (48).
  • Page 14 Assembly Step  Install Seat Pad (25) onto Seat Pad Support (9) using two Washers (91) and two Allen Bolts (83). Slide the Seat Pad Support assembly (9) into Seat Pad Support Receptacle (1) and secure with Locking Pop Pin. Install Back Pad (26) to Back Pad Support (10) using two Allen Bolts (83) and two Washers (91).
  • Page 15 Assembly Step 8 Install a Plastic Washer (69) onto each side of the Long Foam Tube (11). Next, install Upholstered Roller Pad (27) onto each side of Long Foam Tube (11) and secure in place using Big Plug (68). Repeat the above step for the Seat Pad Support (9). Next, install Upholstered Roller Pad (27) onto each Foam Frame (12 &...
  • Page 16 Assembly Step  Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Chest Press Cable (76) as detailed in Figure 9. Follow dotted lines to identify exact location of pulleys. Start by threading cable end into Top Plate (18). You will need the following for installation: Pulley (30) - Qty.
  • Page 17 Assembly Step 10 Note: Stretch all cables out completely and make sure all twisting is removed before install- ing. Install Mid Pulley Cable (77) as detailed in Figure 10. Follow dotted lines to identify exact location of pulleys. Start by installing cable under the pulley at Leg Extension location. You will need the following for installation: Pulley (30) - Qty.
  • Page 18 Assembly Step 11 Note: This step is only used if you do not have the Leg Press attachment. Use the Cable Adapter (70) in place of the pulley. Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Leg Press Cable Substitute (78) as detailed in Figure 11.
  • Page 19 Assembly Step 12 Connect Long Lat Bar (22) to the Chest Press Cable (76) using two Gear Hooks (37) and Short Chain (36). Connect Ab Strap (32) to Mid Pulley Cable (77) using one Gear Hook (37). Connect Short Lat Bar (23) to Mid Pulley Cable (77) using two Gear Hooks (37) and Long Chain (35).
  • Page 20 Assembly Step 13 Install Weight Shrouds (20, 99, 100) to each side of the Main Top Beam (4) using two Washers (91), two Spring Washers (89), and Allen Bolts (86 & 48). Secure the bottom portion of the Weight Shrouds (20, 99, 100) to the Rear Frame (3) using two Washers (46) and two Allen Bolts (48).

  • Page 21: Assembly

    Assembly Congratulations! You have completed the assembly of your new KF-1560.

  • Page 22: Weight Ratios

    Weight Ratios 100% 100% 100%...

  • Page 23: Weight Stack Sticker Placement

    Weight Stack Sticker Placement Your new unit can be purchased with either a 200 LB or 250 LB weight stack. Depending on which weight stack you have purchased will determine which weight stack sticker numbers will be used. The weight stack images below show which weight stack sticker numbers are to be used on your weight stack.

  • Page 24: Cable View

    Cable View...

  • Page 25: Top View

    Top View...

  • Page 26: Exploded View

    Exploded View...

  • Page 27: Parts List

    202-00154 BOLT ALLEN, M8*35 210-00004 WEIGHT PIN 202-00121 SCREW, M12*35 206-00136 RUBBER STOPPER 206-00142 NYLON STOPPER KF-1560 Parts List Rev A Ref # Part # 202-00131 PHILLIP SCREW, M6*15 206-00061 BASE PAD KPS 206-00103 LAT BAR GRIP - KPS 219-00276...

  • Page 28: Warranty Information

    Product. To obtain warranty service, you must contact a Keys authorized retailer, service technician or Keys Fitness at our phone number located in this manual. Any parts determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product.
  • Page 29 Keys Fitness Products, L.P. 400 Distribution Drive, Suite 250 Garland, Texas 5041 Customer Service: 1-888-380-0482...

This manual is also suitable for:

Kf-1860

Table of Contents