Table of Contents
Advertisement
RS-00 OEM Remote Start
RS1-G5, RS3-G5, RS4-G5
RS4-G5 FM (
RS7-G5 FM
REMOTE START SYSTEM
CONGRATULATIONS on your choice of a "Cool Start" System with Data Port Technology for direct connection to bypass
module and Smart Phone. This booklet contains the information necessary for installing your remote starter system.
The RS1, RS3 & RS4 system comes with (2) 1-way AM remotes
The RS4-G5 FM system comes with (2) 1-way FM remotes.
The RS7-G5 FM system comes with a 1-Way FM remote and a 2-Way LCD Pager.
DISCLAIMER:
This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDELINE and the
information contained herein may differ from your vehicle. Crimestopper Security Products, Inc. and its' vendors shall not
be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into
a vehicle in which all systems and associated components are in perfect working condition.
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV 07-2014
1-Way System)
(
2-Way Paging System
INSTALLATION INSTRUCTIONS
)
This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modification could void the user's authority to use the
equipment.
Advertisement
Table of Contents
Related Manuals for CrimeStopper Cool Start RS-00
Summary of Contents for CrimeStopper Cool Start RS-00
- Page 1 READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDELINE and the information contained herein may differ from your vehicle. Crimestopper Security Products, Inc. and its’ vendors shall not be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into a vehicle in which all systems and associated components are in perfect working condition.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Pre-Installation Considerations….………...……...………………………………………………………………..….………..2 Installation Cautions & Warnings………………………………………………………………………………..…..……..…3 Low Current Wiring……..…………………………………………………………………………………………..………...3-8 Power Door Lock Wiring...…………………………………….…………….……..…………...….…………..…..………..9-10 Smart Tachless and Tach Finder Mode………………………………….…………………..…..…….…..……….…11-12 Tach Programming……..…..…….…………………………………………………………………………..….…....13 Diesel Glow Plug Delay..………………….……………………………...……………………...…..…………..…….………14 Option Programming Table………. …….………….……………………………..……………..……..….…..……..15-16 Option Descriptions……………..……………………………...………….……….……..…………………………..……17-21 Antenna Diagram……………………….…………………………………………………………..………………………..…22 Transmitter Programming / 2 Vehicle Programming………………………….….…………..………...…..…..……..23 Manual Transmission Mode……………………….………………………………...…………………….….……..…………24 Connector Plug Diagram……………….………….………………………………...…………………….….……..…………25 Low Current Wiring Diagram………………………………………..………………………………..………..….……….…..26... -
Page 3: Installation Cautions & Warnings
INSTALLATION CAUTIONS & WARNINGS DO NOT extend the Remote start ignition harness length. Mount the module so that main harness reaches all ignition switch wiring. Extending these wires could result in poor or improper performance. DO NOT route any wiring that may become entangled with brake, gas pedals, steering column or any other moving parts in the vehicle. - Page 4 WIRING Low Current 12 Pin Plug YELLOW / BLACK OUTPUT: Ground Out when Running (Relay and/or Module not included ) ANTI-THEFT/ TRANSPONDER YELLOW/BLACK MODULE Diode isolate +12V CONSTANT if using both! 3rd IGN (If needed) IGN SW. ANTI-GRIND RELAY: (Relay not included) IGN 1 IGN 2 ENGINE...
- Page 5 WIRING Low Current 12 Pin Plug BROWN: (-) AUX OUTPUT (Trunk POP or Dome Light Illumination, Option 9) This output is programmable for Trunk Pop or Dome Light Illumination. To eliminate the possibility of accidentally opening up the trunk, there are (3) choices for button press selection. There are 4 choices for this option. 1.
- Page 6 WIRING Low Current 12 Pin Plug RED / BLACK: INPUT SOURCE (12 Volts or Ground) WHITE: PARKING LIGHT OUTPUT The Parking Light circuit can be connected up as a high current positive or negative trigger. Connect to vehicle parking light circuit at the back of light switch or if this is not possible, connect directly to one of the parking lights at the front of the vehicle.
- Page 7 WIRING Low Current 12 Pin Plug GRAY: (-) NEGATIVE HOOD PIN SWITCH Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we recommend one to be installed. When this wire is grounded, the remote start is inhibited. The unit will not attempt to start if hood is open.
-
Page 8: Wiring Led And Valet Switch
1. Remote Start thru data (green wire not connected). This feature only works on newer CANBUS vehicle using a Data Module that supports this feature. With this option you can use both the OEM and Crimestopper remote. 2. Connect the Green input wire to the Negative lock signal wire of the factory system. If your Factory OEM system does not have this type of signal, then a relay is required. -
Page 9: Power Door Lock Wiring Connector
POWER DOOR LOCK WIRING CONNECTOR BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: RED: 12V When using external relays (TERM 86) CS-6600DLM: Dual-relay plug-in module for Reverse GREEN: (-) Negative pulse for LOCK Polarity, Positive, or Aftermarket Motors. - Page 10 BASIC DOOR LOCK DIAGRAMS NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED +12V BLUE BLUE FACTORY FACTORY POWER POWER LOCKING LOCKING RELAYS RELAYS REVERSE POLARITY DOOR LOCK WIRING AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN GREEN FUSED FUSED +12V +12V BLUE BLUE...
-
Page 11: Smart Tachless And Tach Finder Mode
“SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor each time a remote start is requested. - Page 12 TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. When following the steps, the unit will begin to flash the parking lights if you have the Red/White wire connected to a tach source. If lights do not flash, then try another wire until you locate a tach signal that will cause the Parking lights to flash.
-
Page 13: Tach Programming
TACH PROGRAMMING & TACH SIGNALS INTRODUCTION This system has 3 methods of monitoring the engine running. Option #1 controls how the system monitors the engine running. 1. Tach Reference Mode – Monitors Engine R.P.M. - Most reliable method, see Tach programming below. 2. -
Page 14: Diesel Glow Plug Delay
DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-Wait to Start Circuit. This may be needed for various reasons. If your vehicle does not have a viable Wait to Start Circuit, or you cannot locate and identify the circuit, then change your system to Diesel Glow Plug Delay mode. -
Page 15: Option Programming Table
OPTION PROGRAMMING TABLE TX Button #2 TX Button #1 TX Button #3 TX Button #4 Option # Option Description (Unlock) (Lock) (Trunk) (Start) Default Value Engine Monitoring Tach *Tachless* Hybrid Autolock with RPM / Ignition *OFF* “Wake Up” pulse Door Lock Pulse 3 Seconds *0.50 Seconds* Double Unlock... - Page 16 OPTION PROGRAMMING TABLE TX Button #2 TX Button #3 TX Button #4 Option # Option Description TX Button #1 (Lock) (Unlock) (Trunk) (Start) Default Value 30 Sec. Park Lights with Unlock *ON* Horn Pulse (Chirp) 15 milliseconds *20 milliseconds* 40 milliseconds OEM Interface Green input wire 3 pulse = Remote Start *1 Pulse*...
-
Page 17: Option Descriptions
OPTION DESCRIPTIONS 1. Engine Monitoring: This option controls how the system monitors the engine running. You can program for Tachless mode that monitors battery voltage, Tach mode in which the unit uses a Tach signal (RPM) or for Timed Crank as an alternative. There are 4 choices for this option: 1. - Page 18 OPTION DESCRIPTIONS 4. PINK / WHITE WIRE SELECTION: This option controls the Pink / White wire function. 1. Pink / White = Accessory 2 2. Pink / White = Ignition 2 - Default. 3. Pink / White = Start 2 5.
- Page 19 OPTION DESCRIPTIONS 9. BROWN WIRE FUNCTION: AUX 1 - Trunk Pop or Dome Light Output: There are 4 choices for this option. 1. 30 second dome light illumination with unlock. 2. Trunk Pop with ½ second press – Default 3. Double press Trunk Pop. 4.
- Page 20 1. Remote Start thru Data (green wire not connected). This feature only works on newer CANBUS vehicle using a Data Module that supports this feature. With this option you can use both the OEM and Crimestopper remote. 2. Connect the Green input wire to the Negative lock signal wire of the factory system. If your Factory OEM system does not have this type of signal, then a relay is required.
- Page 21 OPTION DESCRIPTIONS 22. TURBO TIMER: Using Remote Start Button The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cool-down without the need for expensive turbo timers.
-
Page 22: Antenna Diagram
29. 1 or 2 VEHICLE Usage: 1-Way Systems only This option allows the remote control to operate 2 Vehicles. The Default = 1-Vehicle only. Note: This Option does not apply to 2-Way Paging systems 30. SMART PHONE BAUD RATE: 9600 OR 115200 31. -
Page 23: Transmitter Programming / 2 Vehicle Programming
TRANSMITTER PROGRAMMING Transmitter Programming: Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be learned at time of programming!! These systems allow storage of up to 4 different remote codes in memory. 1. -
Page 24: Manual Transmission Mode
MANUAL TRANSMISSION MODE MANUAL TRANSMISSION INSTALLATION: OPTION 11 TACH WIRE = White/Red must be connected and programmed. (Default = Tachless Mode) PINK WIRE = (-) Door Switch (default = Glow Plug) GREEN WIRE = (-) Hand Brake (default = OEM Start) After programming Option 11-1, 11-3 or 11-4 for manual transmission mode, the Door Trigger and Hand Brake wire must be connected for the manual transmission remote start procedure. -
Page 25: Connector Plug Diagram
CONNECTOR PLUG DIAGRAM High Current Plug (Black 6 Pin Plug) Control Low Current Plug (Red 3 Pin Plug) Module LED Plug Low Current Plug Door Lock Plug (White 12 Pin Plug) (White 3 Pin Plug) Data Port Protocol must be selected before connecting Data Port Plugs to Fortin or ADS module... -
Page 26: Low Current Wiring Diagram
WIRING DIAGRAM Orange/black OEM Disarm (-) 500mA Factory Car Horn Parking Lights Yellow White (+ or -) (-) 500mA 10 Amps Yellow/black Ground when (-) OEM Arm or Aux 2 Orange (-) 500mA RUNNING (-) 500mA Option # 25 (Bypass Module) Brown (-) 500mA Glow Plug (Default) -
Page 27: Remote Start Diagnostics
REMOTE START DIAGNOSTICS If the system flashes the LED and Parking Lights one to seven times and doesn’t attempt remote. The LED will continue to flashing the error code until the ignition is turned on, it means the following: 1 Parking Light Flash (1 LED Flash) = Problem with Brake Switch. 2 Parking Light Flashes (2 LED Flashes) = Problem with Hood Switch. - Page 28 HIGH CURRENT 6-PIN HIGH-CURRENT CONNECTOR 6 PIN HIGH CURRENT PLUG Diagram not to scale, for illustration purposes only. Your vehicle may differ. Fuse Pink/White 12 Volt Fuse Battery Pink Fuel Brown Pump STARTER Coil Gray START 1 Option # 4 Selectable IGN 1 Default = IGN 2 IGN / ACC / START...
-
Page 29: Data Port
Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module. - Page 30 SMART PHONE DATA PORT This unit includes a Smart Phone Data Port. This is the white 4 pin plug on the side of module, see page 25 for location. This is a “Direct Data to Data” Plug-In for the MS-3 Smart Phone interface module. No other wiring is required. The MS3 is purchased separately.
- Page 32 Phone (800) 998-6880 FAX (805) 581-9500 © 2014 Crimestopper Security Products...