Page 2
Copyright 2000 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.
Declares that the product: Ethernet switching hub Model Number: AT-FH705E This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This...
Page 4
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules.
Page 5
Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur. Wanneer u de ziet, raadpleeg Appendix A voor vertaalde veiligheidsinstructies in uw taal. Important: L'annexe A contient les instructions de sécurité relatives à l'installation de cet équipement. Lorsque vous voyez le symbole , reportez-vous à...
Telephone or Fax Support ...... xi E-mail Support ........xii Returning Products ........xii FTP Server............. xiii For Sales or Corporate Information ..... xiv Tell Us What You Think ....... xiv AT-FH705E Fast Ethernet Switching Hub ..............1 Overview ............1 Features ............2 Physical Description........3 Ports 1 Through 4........3 Port 5 and the Uplink Port ......4...
Page 8
Network Topologies .........7 Installing the AT-FH705E ......9 Verifying the Package Contents ....9 Selecting a Site ........10 Reviewing Safety Guidelines ....11 Installing the Unit on a Desktop ....13 Installing the Unit on a Wall....14 Verifying and Troubleshooting the Installation............16 Warranty Registration ........18 Technical Specifications .........19...
Welcome to Allied Telesyn This guide contains instructions on how to install an Allied Telesyn AT-FH705E Ethernet Switching Hub. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy way to access the most recent documentation and technical information for all of our products.
Note A note provides additional information. Caution A caution indicates that performing or omitting a specific action may result in equipment damage or loss of data. Warning A warning indicates that performing or omitting a specific action may result in bodily injury.
AT-FH705E Installation Guide Telephone or Fax Support For technical support via fax, please fill out the“Technical Support Fax Order” on page 35 and send it to the appropriate location listed below. Americas Germany United States, Canada, Germany, Switzerland, Mexico, Central America,...
E-mail Support United States and Canada TS1@alliedtelesyn.com Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands latin_america@alliedtelesyn.com United Kingdom, Sweden, Norway, Denmark, and Finland support_europe@alliedtelesyn.com Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number.
For Sales or Corporate Information For sales or corporate information contact Allied Telesyn at one of the following locations: Allied Telesyn Allied Telesyn International, Corp. International, Corp. 19800 North Creek Parkway, 960 Stewart Drive, Suite B Suite 200 Sunnyvale, CA 94086 Bothell, WA 98011 Tel: 1 (800) 424-4284 (USA Tel: 1 (425) 487-8880...
AT-FH705E Fast Ethernet Switching Hub Overview The AT-FH705E is a 10Base-T/100Base-TX unmanaged switching hub. The device provides you with a simple, cost-effective solution for Ethernet connectivity between end nodes operating at either 10 or 100 Mbps. Figure 1 AT-FH705E Ethernet Switching Hub...
Features The AT-FH705E Switching Hub has the following features: Five auto-negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors One Uplink port for connecting the AT- FH705E Switching Hub to another switch or hub without a crossover cable IEEE 802.3 and IEEE 802.3u compliant...
AT-FH705E Installation Guide Uplink Figure 3 Back Panel Physical Description The physical description of the device includes: Ports 1 through 4 Port 5 and the Uplink port LEDs Power supply Ports 1 Through 4 Ports 1 through 4 can operate at either 10 Mbps or 100 speed and in either full- or half-duplex mode.
The ports are IEEE802.3u Auto-Negotiation compliant. This means that the ports can automatically configure their speed and duplex mode to match the capabilities of the end nodes connected to the ports. Port 5 and the Uplink Port Port 5 and the Uplink port allow you to connect an additional workstation to the hub or interconnect the switching hub with another switch or hub, without the use of a cross-over...
AT-FH705E Installation Guide Front Panel LEDs Refer to Table 1 for a description of the device LEDs. Table 1 LED Functions LEDs Color Description Power Green On means there is power to the hub. Off means there is no power to the hub.
Table 1 LED Functions (continued) LEDs Color Description On indicates the port is Fdx/Hdx Green operating in full-duplex mode. Off indicates the port is operating in half-duplex mode. Power Supply The AT-FH705E uses an external power adapter that comes standard with the hub.
Network Topologies Figure 4 illustrates a network that consists of one AT-FH705E Ethernet Switching Hub used to interconnect four workstations and a server. In this configuration, the Uplink port is not used. Uplink Figure 4 Single AT-FH705E Switching Hub Topology...
Page 22
FH705E Ethernet Switching Hubs that have been interconnected using the Uplink ports on the two units. Using the Uplink ports eliminates the need for a cross-over cable to interconnect the hubs. Uplink Uplink Figure 5 Multiple AT-FH705E Ethernet Switching Hub Topology...
Make sure that the package includes the following items. If any of the items are damaged or missing, contact your Allied Telesyn representative immediately. One AT-FH705E Switching Hub One power adapter Four self-adhesive rubber feet Warranty card This installation guide...
Selecting a Site Make sure you observe the following site requirements: Make sure you are placing the device in a dust-free and moisture-free environment. Do not block the ventilation openings on the unit. Allow at least 10 centimeters (4 inches) of space at the front and back of the unit for ventilation.
AT-FH705E Installation Guide Observe the following cabling specifications: Connector Type of Maximum Ports Type Cable Distance 1 through 5 RJ-45 Category 5 100 m (328 ft) Uplink RJ-45 Category 5 100 m (328 ft) Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the device.
Page 26
Caution EUROPE - EU: Use TÜV licensed AC adapter of DC 7.5V, 1A. Caution USA/CANADA: Use a UL Listed/CSA Certified AC adapter of DC 7.5V, 1A. Caution Australia: Use a Australian Safety Approved AC adapter of DC 7.5V 1A. Caution Air vents: The air vents must not be blocked on the unit and must have free access to the room ambient air for cooling.
AT-FH705E Installation Guide Installing the Unit on a Desktop To install the device on a desktop, perform the following procedure. To mount the unit on a wall, perform the steps “Installing the Unit on a Wall” on page 14. 1. Attach the four self-adhesive rubber feet to the bottom of the device, positioning them in the indentations.
Uplink port. Note You can use either port 5 or the Uplink port on an AT-FH705E Switching Hub, but you cannot use both simultaneously. 6. Go to the procedure “Verifying and Troubleshooting the Installation” on page 16.
Page 29
AT-FH705E Installation Guide Note For wall-mount installation, you must supply the two screws and plastic anchors or other material necessary to physically mount the device on the wall. 3. Install two plastic anchors and two pan-head screws into the wall, separated by 5 centimeters (approximately 2 inches).
7. Attach the data cables to the AT-FH705E ports. Do not use a cross-over cable to connect workstations or servers to ports 1 through 5. Do not use a cross-over cable to connect another AT-FH705E to the Uplink port. Note...
Page 31
LED should be lit steady or flashing. If a Link/Act LED is OFF, check the following: Check to be sure that the node connected to the port on the AT-FH705E is powered ON. If the node is OFF, power the unit Check to be sure that the distance...
Check to be sure that the distance between the AT-FH705E and the connected network device is no greater than 100 meters (328 feet). Check to be sure that you are using Category 5 cable.
AT-FH705E Installation Guide Technical Specifications Standards Compatibility: IEEE 802.3, IEEE802.3u Interfaces: RJ-45 connectors Physical Dimensions: W x D x H 100 x 78.5 x 26 mm (3.93 x 3.09 x 1.02 in.) Power Supply: Output: 7.5V @ 1A Power Consumption:...
Appendix A Translated Safety and Emission Information Important: This appendix contains multiple- language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog.
Page 36
Importante: questa appendice contiene traduzioni in più lingue degli avvisi di sicurezza di questa guida. Viktig: Dette tillegget inneholder oversettelser til flere språk av sikkerhetsinformasjonen i denne veiledningen. Importante: Este anexo contém traduções em vários idiomas das advertências de segurança neste guia.
Page 37
AT-FH705E Installation Guide Standards: This product meets the following standards: U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn International Manufacture Address: 950 Stewart Drive, Suite B Sunnyvale, CA 94085 USA Manufacture Telephone: 408-730-0950 Declares that the product:...
Page 38
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Page 39
AT-FH705E Installation Guide OPERATING TEMPERATURE: This product is designed for a maximum ambient temperature of 40° degrees C. ALL COUNTRIES: Install product in accordance with local and National Electrical Codes. Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. Hochfrequenzstörung...
Page 40
Standarder: Dette produkt tilfredsstiller de følgende standarder. Radiofrekvens forstyrrelsesemission: EN55022 Klasse B ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. Immunitet EN50082-1 1997 Elektrisk sikkerhed UL 1950 (UL, cUL), EN60950, VCCI Class B SIKKERHED...
Page 41
AT-FH705E Installation Guide Eisen: Dit product voldoet aan de volgende eisen. RFI Emissie EN55022 Klasse B WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. Immuniteit EN50082-1 1997 Electrische Veiligheid...
Page 42
Normes: ce produit est conforme aux normes de suivantes. Emission d’interférences radioélectriques EN55022 Classe B MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. Immunité EN50082 - 1 1997 Sécurité...
Page 43
AT-FH705E Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. Radioaaltojen häirintä EN55022 Luokka B VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. Kestävyys EN50082-1 1997 Sähköturvallisuus UL 1950 (UL, cUL),...
Page 44
Standard: Questo prodotto è conforme ai seguenti standard. Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. Immunità EN50082-1 1997 Sicurezza elettrica UL 1950 (UL, cUL), EN60950,...
Page 45
AT-FH705E Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. RFI stråling EN55022 Klasse B ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. Immunitet EN50082-1 1997 Elektrisk sikkerhet...
Page 46
Padrões: Este produto atende aos seguintes padrões. Emissão de interferência de radiofrequência EN55022 Classe B AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. Imunidade EN50082-1 1997 Segurança Eléctrica UL 1950 (UL, cUL),...
Page 47
AT-FH705E Installation Guide Estándares: Este producto cumple con los siguientes estándares. Emisión RFI EN55022 Clase B ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto.
Page 48
Standarder: Denna produkt uppfyller följande standarder. Radiostörning EN55022 Klass B VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. Immunitet EN50082-1 1997 Elsäkerhet UL 1950 (UL, cUL), EN60950, VCCI Class B SÄKERHET VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN...
Appendix B Technical Support Fax Order Name __________________________________ Company _______________________________ Address ________________________________ City____________________________________ State/Province __________________________ Zip/Postal Code ________________________ Country ________________________________ Phone __________________________________ Fax ___________________________________ Incident Summary Model number of Allied Telesyn product I am using______________________________ Firmware release number of Allied Telesyn product ________________________________ Other network software products I am using (e.g., network managers) ________________...
Page 50
Brief summary of problem _______________ _______________________________________ Conditions (List the steps that led up to the problem. _________________________ _______________________________________ _______________________________________ Detailed description (Please use separate sheet) Please also fax printouts of relevant files such as batch files and configuration files. When completed, fax this sheet to the appropriate Allied Telesyn office.
Appendix C AT-FH705E Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. You can fax or mail this form to the mailing address and fax number at the bottom of the page.