Sound Active Mode; Auto Mode - ADJ VPar Pak User Instructions

VPar Pak
"d.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button so that "Ch.XX" is displayed.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 1 Channel Mode, press the UP or DOWN button until
"Ch.01" is displayed. This is the 1 Channel DMX Mode.
• To run the 2 Channel Mode, press the UP or DOWN button until
"Ch.02" is displayed. This is the 2 Channel DMX Mode.
• To run the 3 Channel Mode, press the UP or DOWN button until
"Ch.03" is displayed. This is the 3 Channel DMX Mode.
• To run the 4 Channel Mode, press the UP or DOWN button until
"Ch.04" is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the UP or DOWN button until
"Ch.05" is displayed. This is the 5 Channel DMX Mode.
• To run the 6 Channel Mode, press the UP or DOWN button until
"Ch.06" is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the UP or DOWN button until
"Ch.07" is displayed. This is the 7 Channel DMX Mode.
• To run the 8 Channel Mode, press the UP or DOWN button until
"Ch.08" is displayed. This is the 8 Channel DMX Mode.
4. Please see pages 15-20 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
RGBA Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When "r.XXX" is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity. After you have finished
adjusting the intensity, or you would like to skip to the next color,
press the SET UP button.
3. When "G.XXX" is displayed you are in Green dimming mode. Press
the UP and DOWN buttons to adjust intensity.
4. When "b.XXX" is displayed you are in Blue dimming mode. Press the
UP and DOWN buttons to adjust intensity.
5. When "A.XXX" is displayed you are in Amber dimming mode. Press
the UP and DOWN buttons to adjust intensity.
6. After you have adjusted the RGBA colors to make your desired color
ADJ Products, LLC - www.adj.com - VPar Pak User Manual Page 8
Operating Instructions VPar Pak
you can then activate strobing by pressing the SET UP button to
enter the Flash (strobe) mode.
7. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).

Sound Active Mode:

In this mode the VPar will react to sound, and chase through the dif-
ferent colors.
1. Plug the fixture in and press the MODE button until "SoXX" is dis-
played. "XX" represents the sound active mode (1-16) currently dis-
played. Use the UP or DOWN buttons to scroll through the 16 sound
active programs.
2. When you have found your desired sound active program press the
SET UP button to adjust the sound sensitivity. When you press SET
UP, "SJ-X" should be displayed. Use the UP or DOWN buttons to
adjust the sensitivity. "SJ-1" is the least sensitive, "SJ-8" is the
most sensitive.

Auto Mode:

There are 3 different Auto Modes to choose from; Color Fade, Color
Change, and both modes running together. The running speed is
adjustable in all 3 modes.
1. Plug the fixture in and press the MODE button until either "AFXX",
"AJXX", or "A-JF" is displayed. Press the SET UP button to scroll
through the 3 different modes.
• AFXX = Color Fade mode, there are 16 Color Fade modes to choose
from. Use the UP or DOWN buttons to scroll through the different
Auto Fade modes.
• AJXX = Color Change mode, there are 16 Color Change modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
2. After you have chosen your desired Auto Mode press the SET UP
button until "SP.XX" is displayed. When this is displayed you can
adjust the running speed of your Auto Mode. Use the UP or DOWN
button to adjust the speed between "SP.01" (slowest) and "SP.16"
(fastest). Once you have set your desired running speed, press the
SET UP button to return to your desired Auto Mode.
ADJ Products, LLC - www.adj.com - VPar Pak User Manual Page 9
Operating Instructions