Husqvarna FS 9900 D Operator's Manual page 37

FS8400 Diesel Model
FS8400 Diesel Model CE
ALL SAWS FEATURE:
Blade Guard Capacity - in. (mm)
Max. Depth of Cut - in. (mm)
Blade Shaft RPM
Approximate Blade Shaft HP
Arbor Size – in. (mm)
Quick Disconnect Blade Flange
Diameter – in. (mm)
Blade Shaft Diameter - in. (mm)
Blade Shaft Bearings
Blade Shaft Drive
Blade Coolant
Blade Guard Attachment
Blade Control
Axle Front
Rear
Wheels Front
Rear
Transmission
Max. Ground Speed
Chassis
Weight – lb. (Kg) – Uncrated
POWER SOURCE:
Engine
Specifications
Max. Horsepower
Displacement cu. in. (l)
Bore / Stroke– in. (mm)
Cylinders / Stroke
Fuel Capacity – gal. (l.)
Oil Capacity – qt. (l)
Air Filter
Starter
Engine Coolant
SAW DIMENSIONS w/ 36" guard:
*Add about 8" (200mm) to Length for 60" (1500mm)
m d o . l e
A Saw Width
B Center to Center Wheel Width (track) – FRONT
Center to Center Wheel Width (track) – REAR
C Outside to Outside Wheel Width - FRONT
Outside to Outside Wheel Width - REAR
D F a r m e W d i h t
E Inner Flange to Inner Flange Width
F a H d n e l E t x n e i s n o
G Min. Saw *Length (handles in, pointer & guard
up)
H Saw *Length (pointer down, handles out)
I Maximum Overall Height (pointer up)
Max Overall Height (top of pre-cleaner, pointer
down)
K Min. Overall Height (no muffler, rotate pre-
cleaner)
L Wheel Base Length
M Guard to Handle Length (handles in)
N Maximum Overall *Length (handles in)
O Maximum Overall *Length (handles extended)
FS8400 DIESEL SPECIFICATIONS
Standard & CE Models
FS8400 FS8400
20" 26"
FS8400 FS8400
450mm 600mm
18 (457) 26 (660)
6.50 (165) 10.50 (267)
2,400 1,800
72 Horsepower
1" (25.4) with single drive pin up to 48" blade; 1" (25.4) with 6 bolt BHP on 60" blade
5 5
(127) (127)
2" (51)
Cast Sealed blade shaft with 4 maintenance-free ball bearings
Dual 10-groove banded 3VX V-belts (20 grooves total)
Zinc plated dual multiple-jet water spray tubes
Slip-on through 36"; Bolt-on for 42" – 60", auto-latch
Electro-hydraulic pump raises blade; switch controlled raise/lower on speed control handle; switch controlled positive depth
stop; dial type cutting depth indicator; blade drive disengagement system (clutch); quick disconnect blade flanges
1.25" (31.75 mm) diameter
Easy Adjust Center Pivot w/2 Hydraulic Powered Wheel Motors
8" x 3" x 1" (203mm x 76mm x 25.4mm) Thick polyurethane tread; sealed ball bearing requiring less maintenance
10" x 3" x 1.25" (254mm x 76mm x 32mm) Solid rubber, Quick disconnect
Hydrostatic Pump, w/2 Hydraulic Wheel Motors connected with hoses, neutral start switch, single handle speed control,
Hydraulic bypass valve for pushing.
Infinitely variable: 0 – 300 FPM forward & reverse. (25 M/min maximum Reverse Speed on CE models)
Heavy-duty, rigid, box and channel section construction
1,890 (858) 1,910 (867)
John Deere Turbocharged Charge Air Cooled Electronic Diesel
5030HF285 EPA Tier 3 Euro Stage 3A Compliant
82.5 @ 2,800 RPM DIN. (61.5 kW)
183 cu. in. (3 liter)
3.39 (86) / 4.13 (105)
5 / 4
9.75 (37)
11.8 (11.2) with filter OR 10.9 (10.6) without filter
Radial Seal with pre-cleaner and restriction indicator
Electric
50/50 Water / Ethyl Glycol Mix
Metric
n I h c s e mm
37-3/8 949
24-5/8 625
25-1/4 642
27-1/4 692
28-3/8 699
9 2 1 - 2 / 7
32-1/2 826
8 2 1 - 2 / 7
71-1/2 1,816
141-1/2 3,594
53 1,346
64-1/2 1,632
49-1/2 1,255
27-3/4 705
75 1,905
106 1/2 2,705
129 3,276
FS8400 FS8400
30" 36"
FS8400 FS8400
750mm 900mm
30 (762) 36 (914)
12.50 (318) 15 (381)
1,600 1,350
5 6
(127) (152)
1,930 (876) 1,960 (890)
9 4
4 2
FS8400 FS8400
42" 48"
FS8400 FS84
1050mm 1200mm
42 (1,067) 48 (1,219)
17.50 (508) 20.50 (508)
1,180 1,080
7 8
(178) (205)
1,990 (903) 2,050 (930)
FS8400
60"
FS8400
1500mm
60 (1,524)
25 (635)
815
10
(254)
2,300 (1044)
37