TriangleTube Prestige Supplement Manual
  1. Manuals
  2. Brands
  3. TriangleTube Manuals
  4. Water Heater
  5. prestige
  6. Supplement manual

TriangleTube Prestige Supplement Manual

Indirect water heater (idwh) sensor application
Hide thumbs Also See for Prestige:
Table of Contents

Advertisement

Quick Links

This document is intended to
be used by a factory trained
and qualified heating
Contractor or service
technician only. Read all
instructions within this
document and within the
PRESTIGE Boiler Installation
and Maintenance Manual,
before proceeding. It is
recommended to follow the
procedures in the steps given,
skipping or missing
procedural steps could result
in severe personal injury,
death or substantial property
damage.
prestige
Indirect Water Heater
(IDWH)
Sensor Application
Supplement
WARNING
Revised Date: 12/3/08

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Prestige and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for TriangleTube Prestige

Summary of Contents for TriangleTube Prestige

  • Page 1 Contractor or service technician only. Read all instructions within this document and within the PRESTIGE Boiler Installation and Maintenance Manual, before proceeding. It is recommended to follow the procedures in the steps given, skipping or missing...

  • Page 3: Table Of Contents

    Table of Contents Product and Safety Information ........1 General Information .
  • Page 4 This document is intended to be used by a factory trained and qualified heating contractor or service technician only. Read all instructions within this doc- ument and within the PRESTIGE Boiler Installation and Maintenance Manual, before proceeding. It is recommended to follow the procedures in the steps...

  • Page 5: General Information

    See Figure 2. The use of this kit will allow the MCBA Control Module of the Prestige boiler to control the domestic storage temperature of the Indirect Water Heater, initiate the burner function during domestic water draw and protect the tank from freezing.
  • Page 6 9. Restore power to the Prestige boiler. Fig. 3: Smart Snap Set Connector Wiring 4. Remove the front jacket panel of the Prestige by removing the thumb screw along the upper edge. Once the thumb screw is removed, pull the panel slightly forward and lift up.
  • Page 7 NOTICE The following section applies to PRESTIGE Boilers using the Honeywell Type 3 McBa control. This control is identified as Honeywell McBa 14201. for PRES- TIGE Boilers with Honeywell Type 5 McBa control (identified as Honeywell McBa 54201), reference pages 13 through 19.
  • Page 8 STEP button to scroll through the entire list of completed and prior to commission of the boiler. parameters before making any additional changes to failure to comply could result in erratic or unre- avoid any potential confusion. liable operation of the Prestige boiler.

  • Page 9: Idwh Sensor Parameter

    2. Press STEP to enter the first parameter setting. parameter 6 could result in erratic or unreliable Continue pressing STEP until the display shows operation of the Prestige resulting in severe person- P_46 al injury, death or substantial property damage.

  • Page 10: Dhw Setpoint Value Addition

    In contrast, a maximum “DHW ON Differential” setting ature of 194ºF. will result in a delayed response to domestic draws. To revise the parameter setting within the Prestige Control Module for the DHW Setpoint Value Addition, the DANGER installer must enter the access code for the control mod- ule as previously described in the Program Access of the MCBA section.

  • Page 11: Dhw Off Differential

    5. Once the desired parameter setting have been revised and stored within the Prestige Control mod- 4. Press the + or - button until the desired “DHW OFF ule, press RESET to exit the CODE mode.

  • Page 12: Additional Dhw Features

    After releasing the STEP button the dis- play will show the current setting. With the addition of the IDWH sensor, the Prestige Control module will now provide a Frost Protection feature to the SMART tank. This feature becomes active when Parameter 46 is set to 12 and cannot be overridden.

  • Page 13: Troubleshooting

    DHW is being used and is properly con- nected to the Prestige low voltage terminals. Ensure Parameter 35 is correctly set for 12 and is stored properly. Once the condition is corrected the errors will automati- cally reset and the Prestige will return to normal operation.

  • Page 14: Factory Settings For Honeywell Type 3 Mcba Parameters

    facToRy SETTInG foR HonEyWEll TyPE 5 McBa PaRaMETERS...
  • Page 15 Additional quality water heating equipment available from Triangle Tube PRESTIGE Solo condEnSInG Wall MounTEd BoIlER 95% AFUE Efficiency Fully modulating Stainless Steel heat exchanger Direct vent with PVC Low NOx Highest water content in the industry Digital display SMaRT SERIES IndIREcT fIREd WaTER HEaTERS...

Table of Contents