Ddtcs Code Setting - Icom IC-F29SR Operating Instructions Manual

4
SETTINGS
Setting the group code number (Continued)
D DTCS code setting
This transceiver is equipped with 84 DTCS codes.
DTCS operation enables silent standby, since you will
only receive calls from group members using the same
DTCS code.
Rotate [VOL] to turn OFF the power.
q
Set [ROTARY SELECTOR] to any channel other
w
than Channel 16.
While holding down
e
rotate [VOL] to turn ON the power.
[ROTARY SELECTOR] to select the desired
Rotate
r
channel (1 to 16) that you want to assign the DTCS
code to.
[Lower] until two beeps sound.
Hold down
t
• The transceiver enters the DTCS code setting mode.
[PTT] the necessary number of times to en-
Push
y
ter the ten's digit of the desired DTCS code number
(grey column) as shown in the list below.
Push [Upper].
u
• The selected number will be announced.
Push [PTT] the necessary number of times to en-
i
ter the one's digit of the desired DTCS code number
(grey column) as shown in the list below.
[Upper].
Push
o
• The selected number will be announced.
!0 If you want to use Inverse mode, push [PTT] again.
• If you want to use Normal mode, skip this step.
!1 Push [Upper] to complete the setting.
!2 Turn OFF the power to exit the DTCS Code Setting
mode.
NOTE:
• If you make a mistake, go back to step q and follow
all the steps again.
• If you want to enter "0", do not push [PTT] in step
t and u, just push [Upper]. Then "zero" will be
announced. To turn OFF the DTCS code, enter "0."
[Example]: DTCS code No. 16 (114) Inverse mode as-
signment to channel 5
Rotate [VOL] to turn OFF the power.
q
While holding down
w
rotate [VOL] to turn ON the power.
• The transceiver enters DTCS Code Setting mode.
[ROTARY SELECTOR] to select channel 5,
Rotate
e
then hold down [Lower] until two beeps sounds.
Push [PTT] one time to enter "1" (the ten's digit) of
r
the number 16.
Push [Upper].
t
• "One" will be announced.
[PTT] six times to enter "6" (the one's digit) of
Push
y
the number 16.
[Upper].
Push
u
• "Six" will be announced.
[PTT] again, to use Inverse mode.
Push
i
Push [Upper] to complete the setting.
o
!0 T urn OFF the power to set the DTCS code.
[PTT], [Upper], and [Lower],
[PTT], [Upper], and [Lower],
[ROTARY SELECTOR]
[PTT]
[Upper]
[Lower]
• Available DTCS code list
No. Code No. Code No. Code No. Code No. Code
01 023 21 132
02 025 22 134
03 026 23 143
031 24 152
04
25 155
05 032
156
06 036 26
07 043 27 162
08 047 28 165
09 051 29 172
10 054 30 174
11 065 31 205
12 071 32 223
13 072 33 226
14 073 34 243
15 074 35 244
16 114 36 245
115 37 251
17
38 261
18 116
19 125 39 263
20 131 40 265
9
[VOL]
41 271 61 466 81
42 306 62 503 82
43 311 63 506 83
44 315 64 516 84
45 331 65 532 00
46 343 66 546
346 67 565
47
68 606
48 351
612
49 364 69
50 365 70 624
51 371 71 627
52 411 72 631
53 412 73 632
54 413 74 654
55 423 75 662
56 431 76 664
57 432 77 703
58 445 78 712
59 464 79 723
465 80 731
60
732
734
743
754
OFF