Recording; Recording Audio (Analog Sources) - Kenwood KRF-V5050D Instruction Manual

22
Muting the sound
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
SP A B TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
Blinks
To cancel
Press the MUTE key again so that the "MUTE" indicator goes off.
• MUTE ON can also be deactivated by turning the volume control
knob.
SOURCE DIRECT playback (for analog input sources only)
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
Press the SOURCE DIRECT key.
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX
• When you press the LISTEN MODE, SOUND, or SET UP keys, or
switch to another input source, SOURCE DIRECT playback will be
canceled.
• If CINEMA EQ. is switched ON, SOURCE DIRECT key will not be
effective.
To cancel
Press the SOURCE DIRECT key again.
• If SOURCE DIRECT playback was activated while in surround mode,
canceling SOURCE DIRECT playback will reactivate the previous
surround mode.
Listening with headphones
1 (VR-506/KRF-V6050D)
Press the SPEAKERS A or B key so that the speaker indicator
goes off.
(VR-505/517/V5050D/V5550D)
Press the SPEAKER key so that the speaker indicator goes off.
Make sure the SPEAKERS
indicators are turned off.
SP A B TI.VOL
L C
CLIP MUTE
LFE
RDS EON PTY
LS S
TP TA NEWS
VR-506/KRF-V6050D
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo playback.
2 Connect headphones to the PHONES jack.
PHONES
3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust the
volume.
Normal playback
L C R
LFE SW
LS S RS
AUTO
MEMO
ST.
TUNED
DSP
Make sure the SP indicators
are turned off.
SP A B TI.VOL
R
CLIP MUTE
RDS EON PTY
RS
TP TA NEWS
VR-505/517/KRF-V5050D/
V5550D

Recording

Recording audio (analog sources)

Recording a music source
When recording a music source, switch the VIDEO2/MONITOR
setting to "MONITOR".
1 Use the INPUT SELECTOR knob to select the source (other than
"TAPE") you want to record.
2 Set the cassette deck or MD recorder to record.
3 Start playback, then start recording.
Recording tapes or MD (with MONITOR function)
When recording a music source, switch the VIDEO2/MONITOR
setting to "MONITOR".
MONITOR = MD/TAPE recording
1 Press the MONITOR key.
2 Use the INPUT SELECTOR knob to select a source other than
"MD/TAPE".
3 Start playback on the cassette deck connected to the MONITOR
jacks and start recording on the cassette deck or MD recorder
connected to the MD/TAPE jacks.
MD/TAPE = MONITOR recording
1 Use the INPUT SELECTOR knob to select "MD/TAPE."
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck or MD recorder
connected to the VIDEO2/MONITOR jacks.
L C R
• To copy tapes using a double cassette deck, refer to the instruction
LFE
manual of the double cassette deck.
LS S RS
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the VIDEO2/
MONITOR jacks of the receiver. If a graphic equalizer is connected, the
MONITOR key should be left in the on position. Alternately, if a cassette
deck equipped with a 3-head system is connected to the VIDEO2/
MONITOR jacks, you will be able to monitor the just-recorded signal
while making recordings on the cassette deck. By switching the MONI-
TOR key on and off, you can compare the sound of the source signal
and the just-recorded signal. For more information, refer to the instruc-
tion manual of the connected component.
MONITOR
INPUT SELECTOR
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
9
9
AUTO
MEMO
ST.
TUNED