Surround Play - Kenwood KRF-V5050D Instruction Manual

Surround play

The DTS compatible models can reproduce a CD, DVD, or LD carrying
the DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing
the mark and DOLBY DIGITAL format digital broadcasts (etc.).
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing
video, DVD, or LD software bearing the
INPUT MODE
LISTEN MODE
LISTEN MODE
RC-R0511
Preparations
• Turn ON related components.
• Complete "Preparing for surround sound" (speaker settings). (
• Use the INPUT SELECTOR to select the component you wish to play
back with surround sound.
• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back.
• Noise will be produced when a DTS source is played by selecting the
analog input.
1
Start playing the video software.
2
Press the LISTEN MODE (LSTN M.) key to select the
listening mode.
The listening mode settings are stored separately for each input. If the
input mode is set to digital auto ("AUTO SOUND" lights), the receiver
selects the optimal listening mode automatically based on the type of
input signal and the speaker settings.
Each press of the LISTEN MODE (LSTN M.) key switches the
setting as listed below.
The listening mode settings are different depending on the type
of input signal.
When the DOLBY DIGITAL signal is input:
(The DOLBY DIGITAL, PROLOGIC, or 3 STEREO indicator lights up.)
1 DOLBY DIGITAL: DOLBY DIGITAL surround
2 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up.)
3 3 STEREO: 3-STEREO surround
4 STEREO: Normal stereo playback
When you select DOLBY DIGITAL
SP A B TI.VOL
L C R
CLIP MUTE
LFE
RDS EON PTY
SL S SR
TP TA NEWS
mark.
INPUT SELECTOR
LSTN M.
INPUT
SELECTOR
RC-R0615/R0617
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
When the DTS signal is input:
(The DTS indicator lights up.)
1 DTS: DTS surround
2 STEREO: Normal stereo playback
When the analog signal or the digital signal (except for
DOLBY DIGITAL or DTS signal) is input:
1 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up.)
2 3 STEREO: 3-STEREO surround (The 3 STEREO indica
tor lights up.)
3 ARENA: DSP surround.
4 JAZZ CLUB: DSP surround.
5 THEATER: DSP surround.
6 STADIUM: DSP surround.
7 DISCO: DSP surround.
8 STEREO: Normal stereo playback. Sound is produced
from the two front channels only.
• If a Dolby Digital signal having more channels than the maximum
number of playback channels available using the receiver's current
settings is input, the DOWNMIX indicator on the front panel lights up
and downmixing is performed to match the number of available
channels.
3
Adjust the volume.
Notes
• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.
• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digital
compatible source component. Connect the Dolby Digital compatible
source component's Dolby Digital format digital audio signal to one of
the DIGITAL INPUT jacks on the back of the receiver. Connect the
normal audio signal correctly to the respective component's AUDIO
9
jacks.
AUTO
MEMO
ST.
TUNED
27
0!@#