Normal Playback; Preparing For Playback - Kenwood KRF-V5050D Instruction Manual

4
Input the distance to the speakers.
20
1 Measure the distance from the listening position to each of the
speakers.
Jot down the distance to each of the speakers.
Distance to front speakers:
Distance to center speaker:
Distance to surround speakers:
2 Use the MULTI CONTROL keys to select the distance to the
front speakers.
The speaker indicator to be adjusted blinks.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
Indication in feet
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SET UP key to accept the settings.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
5 Setup is complete when the input indication reappears.
SP A B TI.VOL
L
CLIP MUTE
LFE
RDS EON PTY
LS
TP TA NEWS
Display when all speakers have been selected.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level. The CLIP indicator will blink to indicate the source signal.
CLIP
RDS
TP
1 Use the INPUT SELECTOR knob to select the source which
input level you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is ON, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key repeatedly until the "INPUT" indication
appears.
3 Use the MULTI CONTROL keys to adjust the input level.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
• The adjustment mode is displayed for approximately eight seconds.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
Preparing for surround sound
____ feet____ meters
____ feet____ meters
____ feet____ meters
FM AUTO SOUND
AM PRO LOGIC
STEREO
MHz 3 STEREO
kHz DOWN MIX
Indication in meters
C R
SW
S RS
FM AUTO SOUND
AM PRO LOGIC
STEREO
MHz 3 STEREO
kHz DOWN MIX

Normal playback

Preparing for playback

Some preparatory steps are needed before starting playback.
ON/STANDBY
KRF-V6050D/
DIGITAL AUTO
S.DIRECT MEMO
V5050D/
ST.
MONITOR
DSP TUNED
V5550D
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/6ch,
DVD (VR-505/KRF-V5550D only) or VIDEO2/MONITOR jacks, make
sure that the input mode setting is correct for the type of audio signal to
be used.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is "TAPE". To change the
source to "MD," follow the steps below:
1 Use the INPUT SELECTOR knob to select "TAPE".
2 Hold down the AUTO/CINEMA EQ. key for more than 2 seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat procedure 2.
Selecting the speaker system (VR-506/KRF-V6050D only)
Press the SPEAKERS A or B key to select the speaker system to
be used.
A ON : Sound from the speakers connected to the SPEAKERS A
B ON : Sound from the speakers connected to the SPEAKERS B
A+B ON : Sound from both the speakers connected to the
A+B OFF : No sound from the speakers. Use this setting when listening
The indicator for the speakers
you want to use should be lit.
SP A B
CLIP
RDS EON
TP TA
VR-506/KRF-V6050D
• Selecting "6ch INPT" by pressing the INPUT MODE key, whereby "DVD/
6ch" is the input source will cause SPEAKER A to be selected automati-
cally.
DIGITAL AUTO
S.DIRECT MEMO
ST.
MONITOR
DSP TUNED
On the VR-505/517/KRF-V5050D/V5550D, press the SPEAKER key to
switch the speakers on and off.
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER (and ON/
STANDBY) key(s).
INPUT MODE
AUTO/CINEMA EQ.
POWER
INPUT SELECTOR
SPEAKERS A/B
(SPEAKER/MUTE)
terminals on the rear panel.
terminals on the rear panel.
SPEAKERS A and B terminals on the rear panel.
with headphones for stereo sound in all playback modes.
The speaker indicator lights.
TI.VOL SP
L C R
MUTE CLIP
LFE SW
PTY RDS EON
LS S RS
NEWS TP
VR-505/517/KRF-V5050D/
V5550D
9
A B TI.VOL
L C R
MUTE
LFE SW
PTY
LS S RS
TA NEWS