Toyota Display Audio system Owner's Manual

Table of Contents

Quick Links

1. BASIC INFORMATION BEFORE OPERATION

Introduction

CONFIRMING DISPLAY AUDIO MODEL

This manual is made up of 2 sections.

The first describing available functions for models without navigation capabili-

ties (WITHOUT NAVIGATION) such as audio and hands-free.

The second describing available functions for models with navigation capabili-

ties (WITH NAVIGATION) such as navigation, audio, and hands-free.

For models that do not have navigation capabilities, refer to the "WITHOUT

NAVIGATION" section. For models that have navigation capabilities, refer to

the "WITH NAVIGATION" section.

Navigation capabilities

Not installed

Installed

■

EXISTENCE OF NAVIGATION CAPABILITIES

Existence of navigation capabilities can be confirmed by performing the following:

1 When the ignition switch is turned to the "ACC" or "ON" position, the initial

screen will be displayed and the system will begin operating.

2 Press the "APPS" button.

Either of the following screens will be displayed.

If your system does not have the "APPS" button, the Display Audio system does not

have navigation capabilities, refer to the "WITHOUT NAVIGATION" section.

Reference

WITHOUT NAVIGATION (1ST SECTION

only)

WITH NAVIGATION (2ND SECTION only)

Table of Contents

Summary of Contents for Toyota Display Audio system

Page 1 2 Press the “APPS” button. Either of the following screens will be displayed. If your system does not have the “APPS” button, the Display Audio system does not have navigation capabilities, refer to the “WITHOUT NAVIGATION” section.
Page 2 1. BASIC INFORMATION BEFORE OPERATION Screen A Screen B If screen A is displayed, the Display Audio system does not have navigation ca- pabilities. If screen B is displayed, the Display Audio system has navigation capabilities. COMMON ILLUSTRATIONS FOR ALL VEHICLE MODELS In this manual, illustrations showing the typical Display Audio system layout, USB port and rear view camera location, etc.
Page 3 1. BASIC INFORMATION BEFORE OPERATION SYMBOLS USED IN ILLUSTRATIONS Safety symbol The symbol of a circle with a slash through it means “Do not”, “Do not do this”, or “Do not let this happen”. Arrows indicating operations Indicates the action (pushing, turning, etc.) used to operate switches and other devices.
Page 4 1. BASIC INFORMATION BEFORE OPERATION...
Page 5 Introduction This manual explains the operation of the Display Audio system. Please read this manual carefully to ensure proper use. Keep this manual in your vehicle at all times. The screen shots in this document and the actual screens of the Display Audio system differ depending on whether the functions and/or a contract existed at the time of producing this document.
Page 6 CAUTION For safety, the driver should not operate ● the Display Audio system while he/she is driving. Insufficient attention to the road and traffic may cause an accident.
Page 8 1. CONTROLS AND FEATURES 1. OVERVIEW BUTTONS The actual design and button position may differ depending on the vehicle. For details, see Section 3 of the vehicle “Owner’s Manual”. Name Function Page Touch screen By touching the screen with your finger, you can display control the selected functions.
Page 9 1. CONTROLS AND FEATURES Name Function Page Press this button to access the vehicle information “CAR” button* system. This button is used for an add-on external naviga- “APPS” button* — tion system. (If equipped) Press this knob to turn the audio system on and off, “PWR/VOL”...
Page 10 1. CONTROLS AND FEATURES 2. SYSTEM FUNCTION INDEX AUDIO SYSTEM To access the audio system, press the “AUDIO” button. The audio control screen will be displayed. Audio sources: Radio, ® CDs, iPod, USB, AUX and Bluetooth dio. For details, see pages 13. SETUP To customize the function settings, press the “SETUP”...
Page 11: Touch Screen Operation
1. CONTROLS AND FEATURES 3. TOUCH SCREEN OPERATION This system is operated mainly by the screen buttons. To prevent damage to the screen, lightly touch the screen buttons with your finger. When a screen button is touched, a beep sounds. (To set a beep sound, see page 93.) Do not use objects other than your finger to touch the screen.
Page 12: Quick Reference
1. AUDIO SYSTEM OPERATION 1. QUICK REFERENCE To access the audio system, press the “AUDIO” button. The audio system turns on in the last mode used. The actual design and button position may differ depending on the vehicle. For details, see Section 3 of the vehicle “Owner’s Manual”. Name Function Page...
Page 13 1. AUDIO SYSTEM OPERATION Name Function Page Press to turn the audio system on and off, and turn “PWR/VOL” knob to adjust the volume. button Press to eject a disc. *: If equipped...
Page 14: Some Basics
1. AUDIO SYSTEM OPERATION 2. SOME BASICS This section describes some of the ba- TURNING THE AUDIO sic features of the audio system. Some SYSTEM ON OR OFF information may not pertain to your system. Your audio system works when the en- gine switch is turned to the “ACC”...
Page 15 1. AUDIO SYSTEM OPERATION When a list is displayed Touch a desired audio source. When a list is displayed on the screen, turn the “TUNE/SCROLL” knob to move the cursor box to select a desired item from the list, and pressing the knob will play it.
Page 16 1. AUDIO SYSTEM OPERATION Touch the “DSP” tab to display this SURROUND FUNCTION screen. (IF EQUIPPED) Without JBL sound system Touch “On” of “Surround”. Touch “OK”. TONE AND BALANCE TONE How good an audio program sounds is With JBL sound system largely determined by the mix of the treble, mid and bass levels.
Page 17 1. AUDIO SYSTEM OPERATION Touch the “Sound” tab to display this screen. Touch the desired screen button. “Treble” “+” or “-”: To adjust high- pitched tones. “Mid” “+” or “-”: To adjust mid-pitched tones. “Bass” “+” or “-”: To adjust low-pitched tones.
Page 18 1. AUDIO SYSTEM OPERATION 3. RADIO OPERATION (WITH Display Audio SYSTEM) SWITCHING TO RADIO MODE PRESETTING A STATION Press the “AUDIO” button. Tune in the desired station. Touch one of the left side screen but- tons (1-6) and hold it until a beep is heard.
Page 19 1. AUDIO SYSTEM OPERATION SELECTING A STATION RADIO BROADCAST DATA SYSTEM Tune in the desired station using one of the following methods. This audio system is equipped with Ra- dio Broadcast Data Systems (RBDS). Preset tuning: Touch one of the preset RBDS mode allows text messages to channels on the left side of the screen to be received from radio stations that uti-...
Page 20 1. AUDIO SYSTEM OPERATION Touch “TYPE >” or “< TYPE” to move TRAFFIC ANNOUNCEMENT forward and backward through the pro- gram list. A station that regularly broadcasts traf- fic information is automatically located. Once a program type has been set, “TYPE SEEK”...
Page 21 1. AUDIO SYSTEM OPERATION 4. RADIO OPERATION (WITH Premium Display Audio SYSTEM) SWITCHING TO RADIO MODE PRESETTING A STATION Press the “AUDIO” button. Radio mode has a mix preset function, which can store up to 36 stations (6 station per page 6 page) from any of the AM, FM or SAT bands.
Page 22 1. AUDIO SYSTEM OPERATION SELECTING A STATION RADIO BROADCAST DATA SYSTEM Tune in the desired station using one of the following methods. This audio system is equipped with Ra- dio Broadcast Data Systems (RBDS). Preset tuning: Touch one of the mix pre- RBDS mode allows text messages to set channels on the left side of the screen be received from radio stations that uti-...
Page 23 1. AUDIO SYSTEM OPERATION Touch “TYPE >” or “< TYPE” to move TRAFFIC ANNOUNCEMENT forward and backward through the pro- gram list. A station that regularly broadcasts traf- fic information is automatically located. Once a program type has been set, “TYPE SEEK”...
Page 24 1. AUDIO SYSTEM OPERATION INFORMATION USING HD Radio™ TECHNOLOGY Touch “Text”. HD Radio™ Technology is the digital evolution of analog AM/FM radio. Your radio product has a special receiver which allows it to receive digital broadcasts (where available) addition to the analog broadcasts it already receives.
Page 25 1. AUDIO SYSTEM OPERATION INFORMATION ● If tagging the music information fails, Touch “Tag” to bookmark the music “Saving the HD Radio tag failed.” will be information. displayed on the screen. If this occurs, tag the information again. ● HD Radio™ stations can be preset. Open the cover and connect iPod us- ing an iPod cable.
Page 26: Troubleshooting Guide
1. AUDIO SYSTEM OPERATION TROUBLESHOOTING GUIDE Experience Cause Action Mismatch of time alignment The radio stations analog a users may hear a short and digital volume is not None, radio broadcast issue. A period of programming re- properly aligned or the sta- user can contact the radio station.
Page 27 Canadian provinces. SATELLITE TUNER HOW TO SUBSCRIBE TECHNOLOGY NOTICE It is necessary to enter into a separate Toyota’s satellite radio tuners are ® service agreement with XM Satellite awarded Type Approval Certificates Radio in order to receive satellite ®...
Page 28 1. AUDIO SYSTEM OPERATION SWITCHING TO SATELLITE CHANNEL CATEGORY RADIO MODE Touch “Options”. Press the “AUDIO” button. Touch either “TYPE >” or “< TYPE” to go to the next or previous category. The audio system turns on in the last mode used.
Page 29 1. AUDIO SYSTEM OPERATION SELECTING A CHANNEL DISPLAYING THE TITLE AND NAME Tune in the desired channel using one of the following methods. Touching “Text” displays the artist name and song title you are currently Preset tuning: Touch the channel selector listening to.
Page 30 Check whether the XM tenna cable is attached securely. Ck Antenna A short circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer for assistance. ® You have not subscribed to XM Satellite Radio. The radio is be- ®...
Page 31 1. AUDIO SYSTEM OPERATION NOTICE ● This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation.
Page 32: Cd Player Operation
1. AUDIO SYSTEM OPERATION 6. CD PLAYER OPERATION The CD player can play audio CDs, CD text and MP3/WMA discs. (a)Audio CD, CD text (see page 35) (b)MP3/WMA disc (see page 37) For appropriate discs for this player, see “AUDIO SYSTEM OPERATING HINTS”...
Page 33 1. AUDIO SYSTEM OPERATION SWITCHING TO CD MODE PLAYING AN AUDIO CD Press the “AUDIO” button. If a CD-TEXT disc is inserted, the title of the track and disc currently being played will be displayed. : Touch to pause the track. The audio system turns on in the last mode used.
Page 34 1. AUDIO SYSTEM OPERATION SELECTING A DESIRED PLAYING REPEAT AND TRACK RANDOM ORDER Select a desired track using one of the following methods. (Repeat mode): Use it to automat- ically repeat the track you are currently lis- tening to. The repeat mode changes as follows each time the screen button is touched.
Page 35 1. AUDIO SYSTEM OPERATION SELECTING A DESIRED FILE PLAYING A MP3/WMA DISC Select a desired file using one of the following methods. The title of the file and folder currently being played will be displayed. : Touch to pause the file. : Touch to resume playing the file.
Page 36 1. AUDIO SYSTEM OPERATION SELECTING A DESIRED PLAYING REPEAT AND FOLDER RANDOM ORDER Touch “Folders” on the screen. The folder list will be displayed. (Repeat mode): Use it to automat- ically repeat the file or folder you are cur- Touch a desired folder from the list. rently listening to.
Page 37: Ipod Operation
1. AUDIO SYSTEM OPERATION 7. iPod OPERATION Connecting an iPod with the USB port CONNECTING AN iPod enables users to enjoy music via the vehicle speakers. Open the cover of the USB/AUX port and connect an iPod. CAUTION ● Do not connect an iPod or operate the device controls while driving.
Page 38 1. AUDIO SYSTEM OPERATION Fast forward and Reverse: Press and Touch “Source” or press “AUDIO” hold the “ ” or “ ” of “SEEK/TRACK” but- button to display the audio source se- ton to fast forward or reverse. When you lection screen.
Page 39 1. AUDIO SYSTEM OPERATION SELECTING A DESIRED SONG SELECTING A PLAY MODE Touch “Browse” on the screen. Select a desired song using one of the following methods. Touch a desired play mode tab button, such as playlists, artists, albums, songs, podcasts or audio book. And then select the song on each play “SEEK/TRACK”...
Page 40 1. AUDIO SYSTEM OPERATION PLAYING REPEAT AND SHUFFLE (Repeat mode): Use it to automat- ically repeat the song you are currently lis- tening to. The repeat mode changes as follows each time the screen button is touched. :Repeating the song :OFF (Shuffle mode): Use it for auto- matic shuffling of the songs or albums in...
Page 41 1. AUDIO SYSTEM OPERATION 8. USB MEMORY OPERATION Connecting a USB memory with the CONNECTING A USB USB port enables users to enjoy music MEMORY via the vehicle speakers. Open the cover of the USB/AUX port CAUTION and connect a USB memory. ●...
Page 42 1. AUDIO SYSTEM OPERATION Fast forward and Reverse: Press and Touch “Source” or press “AUDIO” hold the “ ” or “ ” of “SEEK/TRACK” but- button to display the audio source se- ton to fast forward or reverse. When you lection screen.
Page 43 1. AUDIO SYSTEM OPERATION File list: A desired file can be selected Touch a desired folder from the list. from a list. The file list for the folder will be dis- Touch “Files” on the screen. The list will played. be displayed.
Page 44 1. AUDIO SYSTEM OPERATION (Random mode): Use it for auto- matic random selection of the file. The random mode changes as follows each time the screen button is touched. :Playing the files on the fold- er in random order :Playing the files in all the folders in random order :OFF...
Page 45 1. AUDIO SYSTEM OPERATION 9. AUX DEVICE OPERATION Connecting a portable audio device CONNECTING A PORTABLE with the AUX port enables users to en- AUDIO DEVICE joy music via the vehicle speakers. Open the cover of the USB/AUX port CAUTION and connect a portable audio device.
Page 46 1. AUDIO SYSTEM OPERATION SWITCHING TO AUX MODE PLAYING A PORTABLE AUDIO DEVICE Press the “AUDIO” button. Only the volume can be adjusted using the audio system controls. The remaining controls need to be operated on the porta- The audio system turns on in the last ble audio device itself.
Page 47 This is a profile to remote control the INFORMATION A/V equipments. In the following conditions, the system ● ● Refer http://www.toyota.com/ may not function. ® Bluetooth/ to find approved Bluetooth • The portable audio player is turned devices for this system. off.
Page 48 1. AUDIO SYSTEM OPERATION Touch “Source” or press “AUDIO” CAUTION button to display the audio source se- lection screen. ● FCC WARNING: Changes or modifica- tions not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 49 1. AUDIO SYSTEM OPERATION Touch “Connect” on the screen. When the connection is completed, this screen is displayed. Touch “Yes” to connect your portable Once you have registered it, the system player. automatically connects to your portable audio player device every time you start your vehicle.
Page 50 1. AUDIO SYSTEM OPERATION Touch the portable audio device name to connect. “Connection Method” “From Vehicle”: Connect the audio system to the portable audio player. If you want to add a new device, touch “Add New”. You can register up to 5 However, depending on the type of porta- devices.
Page 51 1. AUDIO SYSTEM OPERATION ® STATUS DISPLAY PLAYING A Bluetooth AUDIO PLAYER ® Indicates the condition of the Bluetooth connection. The title of the track and album currently being played will be displayed. Good connection INFORMATION ® An antenna for the Bluetooth connec- ●...
Page 52 1. AUDIO SYSTEM OPERATION Track list: A desired track can be selected Indicates the amount of battery charge from a list. left. Touch “Tracks” on the screen. The list will be displayed. Empty Full INFORMATION ● Depending on the type of portable audio players, remaining battery charge is not displayed.
Page 53 1. AUDIO SYSTEM OPERATION Touch a desired album from the list. (Random mode): Use it for auto- The track list for the album will be dis- matic random selection of the track. played. The random mode changes as follows each time the screen button is touched. :Playing the tracks on the album in random order :Playing the tracks on all the...
Page 54 1. AUDIO SYSTEM OPERATION 11. STEERING SWITCHES Some parts of the audio system can be “ ” “ ” switch adjusted with the switches on the Radio steering wheel. To select a preset station: Press the “ ” switch. or “ ” STEERING SWITCHES (WITH To seek a radio station: Press and hold TWO DIRECTION STEERING...
Page 55 1. AUDIO SYSTEM OPERATION To seek a station: Press and hold the “ ” STEERING SWITCHES (WITH or “ ” side of the switch until a beep is FOUR DIRECTION STEERING heard. Repeat this to find the next station. SWITCH) If either side of the switch is pressed dur- ing seek mode, seeking will be canceled.
Page 56 1. AUDIO SYSTEM OPERATION “MODE” switch Press the “MODE” switch to select an audio mode. Each press changes the mode sequentially if the desired mode is ready to use. To turn the audio system on, press the “MODE” switch. Press and hold the “MODE” switch until you hear a beep and the music will pause or be muted.
Page 57 1. AUDIO SYSTEM OPERATION 12. AUDIO SYSTEM OPERATING HINTS NOTICE Fading and drifting stations: Generally, ● To avoid damaging the audio system: the effective range of FM is about 25 miles • Be careful not to spill beverages over (40 km). Once outside this range, you may the audio system.
Page 58 1. AUDIO SYSTEM OPERATION ® COMPATIBLE MODELS Cargo loaded on the roof luggage carrier, Software especially metal objects, may adversely Model Generation Version ® affect the reception of XM Satellite Radio. iPod 1.3.0 Alternation or modifications carried out 1.1.2 without appropriate authorization may iPod invalidate the user’s right to operate the 2.0.1...
Page 59 1. AUDIO SYSTEM OPERATION USB MEMORY USB memory that can be used for MP3 and WMA playback. Audio CDs • USB communication formats: USB 2.0 FS (12 Mbps) ® • File formats: FAT 16/32 (Windows • Correspondence class: Mass storage class Use only discs marked as shown above.
Page 60 1. AUDIO SYSTEM OPERATION Low quality discs Correct Wrong Handle discs carefully, especially when you are inserting them. Hold them on the Labeled discs edge and do not bend them. Avoid getting fingerprints on them, particularly on the shiny side. Dirt, scratches, warping, pin holes, or other disc damage could cause the CD player to skip or to repeat a section of a...
Page 61 1. AUDIO SYSTEM OPERATION SAMPLING FREQUENCY MP3/WMA FILES MP3 files: MP3 (MPEG Audio Layer 3) and WMA MPEG 1 AUDIO LAYER 3 32, 44.1, 48 (Windows Media Audio) are audio com- pression standards. The MP3/WMA player can play MP3 and MPEG2 AUDIO LAYER3 16, 22.05, 24 WMA files on CD-ROM, CD-R and CD-...
Page 62 1. AUDIO SYSTEM OPERATION MP3/WMA files in folders up to 8 levels CD-R AND CD-RW DISCS deep can be played. However, the start of playback may be delayed when using CD-R/CD-RW discs that have not been discs containing numerous levels of fold- subject to the “finalizing process”...
Page 63 1. AUDIO SYSTEM OPERATION TERMS MP3 is an audio compression standard determined by a working group (MPEG) of PACKET WRITE the ISO (International Standard Organiza- tion). MP3 compresses audio data to This is a general term that describes the about 1/10 the size of that on conventional process of writing data on-demand to CD- discs.
Page 64 1. AUDIO SYSTEM OPERATION...
Page 65 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION 1. QUICK REFERENCE This screen can be used to make a phone call. To display the “Phone” screen, press the switch on the steering wheel or the button. The actual design and button position may differ depending on the vehicle. For details, see Section 3 of the vehicle “Owner’s Manual”.
Page 66 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION 2. HANDS-FREE SYSTEM ® Bluetooth hands-free system allows INFORMATION you to make or receive a call without ● If your cellular phone does not support ® taking your hands off the steering Bluetooth , this system will not function. wheel by connecting your cellular Depending on the cellular phone mod- ●...
Page 67 ® HFP, you cannot register the Bluetooth adjust the volume. phone, and take OPP or PBAP service individually. Refer http://www.toyota.com/ ● ® Bluetooth/ to find approved Bluetooth devices for this system. You can use the microphone when talking on the phone.
Page 68 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION ABOUT THE PHONEBOOK IN INFORMATION THIS SYSTEM ● The other party’s voice outputs from the front speaker. When the received calls or received voice outputs, the audio The following data is stored for every reg- from the audio system will be muted.
Page 69 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION PHONE STATUS DISPLAY CAUTION ● FCC WARNING: Changes or modifica- tions not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ● CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radi- ation exposure limits set forth for uncon-...
Page 70 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION Indicates the receiving area. “Rm” is displayed when receiving in Roaming area. The receiving area may not be displayed depending on the phone you have. Indicates the level of reception. Poor Excellent The level of reception does not always correspond with the one of your cellular phone.
Page 71 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION ® 3. REGISTER A Bluetooth PHONE When this screen is displayed, perform ® To use the Bluetooth hands-free a device discovery from your Bluetooth system, you need to register your phone. phone into the system. Once you have registered it, you can make hands-free calls.
Page 72 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION When the connection is completed, SELECTING AND ADDING A this screen is displayed. ® Bluetooth PHONE have registered some ® Bluetooth devices, you can change the device connected and add a new device. Touch “Connect Phone”. Once you have registered it, the system ®...
Page 73 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION ® 4. CALL ON THE Bluetooth PHONE ® BY PHONEBOOK After you register the Bluetooth phone, call using ® You can make a call using the Bluetooth hands-free system. phonebook data which is transferred from your cellular phone.
Page 74 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION WHEN THE PHONEBOOK IS BY SPEED DIAL EMPTY You can call using registered phone Touch “Contacts”. numbers which can be selected from a phonebook. (See “SPEED DIALS SETTING” on page 111 for registering the speed dial.) Press the switch on the steering wheel or the...
Page 75 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION Touch or press the switch BY CALL HISTORY on the steering wheel. You can make a call using the call history which has 4 functions below. All: all the calls (missed, incoming or out- going) Missed: calls which you missed Incoming: calls which you received...
Page 76 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION Say the command displayed on the BY VOICE RECOGNITION screen. (IF EQUIPPED) Calls can be made by giving a voice command. This can be operated while driving. Press the talk switch. If a desired outcome is not shown, or if no selections are available, perform one of the following to return to the previous screen:...
Page 77 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION Say “Dial” to call the phone number. VOICE COMMAND EXAMPLE: CALL NAME Press the talk switch. Say the name, or the name and type of phone, of a registered contact. VOICE COMMAND EXAMPLE: DIAL NUMBER Press the talk switch.
Page 78 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION As the system cannot recognize additional numbers, say the complete number with- out stopping. When the system recognizes multiple phone numbers, a phone number candi- date list will be displayed on the screen. If the desired phone number is not displayed on the top of the screen, say the number of the desired phone number from the...
Page 79 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION ® 5. RECEIVE ON THE Bluetooth PHONE When a call is received, this screen is displayed with a sound. To answer the phone: Press the switch on the steering wheel or touch To refuse to receive the call: Press the switch on the steering wheel or touch...
Page 80 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION ® 6. TALK ON THE Bluetooth PHONE While you are talking on the phone, WHEN YOU TOUCH “0-9” this screen is displayed. You can do Enter a number by touching the num- the operation below on the screen. ber keys.
Page 81 ® 1. Bluetooth HANDS-FREE SYSTEM OPERATION INTERRUPT CALL INFORMATION ● The continuous tone signal is the When the call is interrupted by the third marked sign (p or w) and the number fol- lowing phone number. (ex. party while talking, this screen is 056133w0123p#1 ) displayed.
Page 82 1. VEHICLE INFORMATION 1. QUICK REFERENCE Fuel consumption information and tire pressure value can be displayed. To access the vehicle information system, press the “CAR” button. The actual design and button position may differ depending on the vehicle. For details, see Section 3 of the vehicle “Owner’s Manual”. The “Information”...
Page 83 1. VEHICLE INFORMATION 2. FUEL CONSUMPTION TRIP INFORMATION FUEL CONSUMPTION (VEHICLES WITH HYBRID SYSTEM) Fuel consumption such as shown be- low can be displayed on the screen. For details see Section 1-1 of the vehi- cle “Owner’s Manual”. Energy monitor If the “Trip Information”...
Page 84 1. VEHICLE INFORMATION HISTORY If the “History” screen is not displayed, touch “History”. Name Previous fuel economy record Current fuel economy Best recorded fuel economy The average fuel consumption history is divided by color into past averages and the average fuel consumption since the last reset.
Page 85 1. VEHICLE INFORMATION 3. TIRE PRESSURE WARNING SYSTEM Touch “Tire Pressure”. Vehicles equipped with a tire pres- sure warning system will display a warning screen in addition to a warning indication on the meter if tire pressure becomes low. For in- formation on the tire pressure warning system, refer to the vehi- cle “Owner’s Manual”.
Page 86 1. VEHICLE INFORMATION...
Page 87 Settings are available for vehicle customization. “Audio”* Settings are available for HD Radio™ system. Settings are available for phone sound, phone- “Phone” book, etc. : Vehicles with Premium Display Audio system : Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Page 88: General Settings
1. SETUP OPERATION 2. GENERAL SETTINGS Settings are available for language se- SCREENS FOR GENERAL lection, operation sounds, screen ani- SETTINGS mation, etc. Press the “SETUP” button. On this screen, the following functions are operational. Function Touch “General”. You can change the language. (See “SELECTING LAN-...
Page 89 1. SETUP OPERATION SELECTING A LANGUAGE DELETE PERSONAL DATA Press the “SETUP” button. The desired language can be selected. Touch “General” on the “Setup” Press the “SETUP” button. screen. Touch “General” on the “Setup” Touch “Delete Personal Data”. screen. Touch “Language”. Touch “Delete”.
Page 90 1. SETUP OPERATION 3. GUIDANCE SETTINGS (WITH Premium Display Audio SYSTEM) Voice recognition guidance for Blue- SCREEN FOR VOICE ® tooth hands-free systems can be set. GUIDANCE SETTINGS Press the “SETUP” button. On this screen, the following functions can be performed.
Page 91: Display Settings
1. SETUP OPERATION 4. DISPLAY SETTINGS You can adjust the contrast and bright- TURN OFF DISPLAY ness of the screen. You can also turn the display off. Press the “SETUP” button. Press the “SETUP” button. Touch “Display” on the “Setup” screen.
Page 92 1. SETUP OPERATION ADJUST CONTRAST/ BRIGHTNESS Press the “SETUP” button. Touch “Display” on the “Setup” screen. Touch “General” or “Camera”, in which you want to make an adjust- ment. Select “Contrast” or “Brightness” using the Adjust the contrast or brightness using the “+”...
Page 93 1. SETUP OPERATION ® 5. Bluetooth SETTINGS You can confirm and change the REGISTERED DEVICES ® Bluetooth settings. Press the “SETUP” button. Press the “SETUP” button. Touch “Bluetooth*” on the “Setup” screen. *: Bluetooth is a registered trademark of Bluetooth SIG, Inc. Touch “Registered Devices”.
Page 94 1. SETUP OPERATION When this screen is displayed, perform INFORMATION a device discovery from your Bluetooth ● For details on device discovery for your device. Bluetooth phone, refer to the Bluetooth phone’s user’s guide. When register your phone, ● ® Bluetooth audio will disconnect.
Page 95 1. SETUP OPERATION DISPLAYING DEVICE DETAILS Name Function name Touch “Details” to display a device “Device Name” ® Bluetooth network. detail. The address peculiar to the system. You cannot “Device change it. If the same Address” device name dis- played on the screen of your device, refer to it.
Page 96 1. SETUP OPERATION Touch “OK”. Select the device to connect. “From Vehicle”: Connect the audio sys- tem to the portable audio player. “From Audio Player”: Connect the porta- ble audio player to the audio system. ® ■ INITIALIZING Bluetooth SETTINGS You can initialize the settings.
Page 97 1. SETUP OPERATION Touch “Connect Audio Player”. ® DETAILED Bluetooth SETTINGS Press the “SETUP” button. Touch “Bluetooth*” on the “Setup” screen. Touch “Detailed Bluetooth* Settings”. Select the device to connect. *: Bluetooth is a registered trademark of ® Bluetooth SIG, Inc. The Bluetooth mark is displayed when you connect the device.
Page 98 1. SETUP OPERATION The information displays the following ® CHANGING THE Bluetooth items. POWER Name Function Touch “Bluetooth* Power”. It is available to set wheth- “Bluetooth* er registered devices will Power” be connected automatical- ly or not. name “Device ® Bluetooth network.
Page 99 1. SETUP OPERATION Touch “Save”. EDITING THE PASSCODE When you start your vehicle and the Touch “Passcode”. ® Bluetooth phone automatically connected, connection check displayed. Input a passcode and touch “OK”. You can select the state of “Display Phone Status”. On: The status is displayed.
Page 100 1. SETUP OPERATION When you start your vehicle and the ® Bluetooth portable audio player automatically connected, the connection check is displayed. You can select the state of “Display Audio Player Status”. On: The status is displayed. Off: The status is not displayed. ®...
Page 101: Phone Settings
1. SETUP OPERATION 6. PHONE SETTINGS Phone settings can be changed. PHONE SOUND SETTINGS Press the “SETUP” button. Touch “Phone Sound Settings”. Change each setting according to the following procedures. Touch “Phone”. When you complete all settings, touch Touch the items to be set. “Save”.
Page 102 1. SETUP OPERATION Touch “Default”. RING TONE VOLUME SETTING Touch “Ring Tone Volume”. Touch “-” or “+” to adjust the ring vol- ume. PHONEBOOK Press the “SETUP” button. Touch “Phone”. Touch “OK”. Touch “Phonebook”. RING TONE SELECTING Touch “Ring Tone”. Touch “Tone 1”, “Tone 2”...
Page 103 1. SETUP OPERATION Touch “Transfer Contacts”. PHONEBOOK SETTINGS Touch “Manage Contacts”. PBAP compatible models This screen is displayed. (See page Touch the items to be set. 109.) Please refer to the following pages for PBAP incompatible but OPP compatible each setting. models This screen is displayed.
Page 104 1. SETUP OPERATION Touch “Automatically Download INFORMATION Contacts” and select “On” or “Off”. ● Transfer it while the engine is running. ● Depending on the cellular phone, call history will be also transferred. ● When transferring the phonebook data to the cellular phone, the hands-free may be unavailable.
Page 105 1. SETUP OPERATION Transfer the phonebook data to the Transfer the phonebook data to the ® ® system using the Bluetooth phone. system using the Bluetooth phone. Depending on the type of cellular phone, Depending on the type of cellular phone, OBEX authentication may be required OBEX authentication may be required when transferring phonebook data.
Page 106 1. SETUP OPERATION Touch “Delete Contacts”. Touch “Delete”. Select the name you want to delete or INFORMATION touch “All Delete”. ® ● When you delete a Bluetooth phone, the phonebook data will be deleted at the same time. SPEED DIALS SETTING Speed dials setting is accessed from the “Speed Dials”...
Page 107 1. SETUP OPERATION ■ REGISTERING THE SPEED DIAL You can also display the “Speed Dials” FROM CONTACTS screen in the following way. From “Speed Dial” screen You can register the phone number from phonebook. Up to 18 numbers Press the switch on the steering per phone can be registered.
Page 108 1. SETUP OPERATION Touch the screen button you want to You can also register the speed dial in register in. the following ways. From “Speed Dial” screen Press the switch on the steering wheel or the button. Touch “Speed Dials”. Touch “(add new)”.
Page 109 1. SETUP OPERATION From “Call History” screen Touch the desired phone number. Press the switch on the steering wheel or the button. Touch “Call History”. Touch the desired phone number. Touch “Add Speed Dial”. From “Contact” screen Press the switch on the steering wheel or the button.
Page 110 1. SETUP OPERATION DELETING CALL HISTORY You can also delete the call history in the following way. You can delete the call history. Press the switch on the steering For PBAP compatible phone, delete the phonebook data after setting “Au- wheel or the button.
Page 111 1. SETUP OPERATION 7. AUDIO SETTINGS (WITH Premium Display Audio SYSTEM) Select the desired setting from “HD HD Radio™ system can be set using Radio/Analog Setting”. the following procedure: Press the “SETUP” button. Screen button Function Touch to receive both an- “All”...
Page 112: Vehicle Settings
1. SETUP OPERATION 8. VEHICLE SETTINGS After changing the settings, touch Vehicle customization settings can be “Save”. changed. A message indicating that the settings are Press the “SETUP” button. being saved will appear. Do not perform any other operations while this message is displayed.
Page 113 1. SETUP OPERATION...
Page 114 1. REAR VIEW MONITOR SYSTEM 1. REAR VIEW MONITOR SYSTEM OPERATION The rear view monitor system assists CAUTION the driver by displaying an image of the view behind the vehicle while backing ● Never depend on the rear view monitor system entirely when...
Page 115 Guide lines are displayed on the may change. Be sure to have the cam- screen. era’s position and mounting angle checked at your Toyota dealer. ● As the camera has a water proof con- struction, do not detach, disassemble or modify it.
Page 116 1. REAR VIEW MONITOR SYSTEM AREA DISPLAYED ON SCREEN Image is displayed approximately level on screen. INFORMATION ● The area displayed on the screen may vary according to vehicle orientation or road conditions. THE REAR VIEW MONITOR SYSTEM CAMERA The rear view monitor system camera is located as shown in the illustration.
Page 117 1. REAR VIEW MONITOR SYSTEM On some models INFORMATION ● The camera uses a special lens. The distance of the image that appears on the screen differs from the actual dis- tance. ● In the following cases, it may become difficult to see the images on the screen, even when the system is functioning.
Page 118 1. REAR VIEW MONITOR SYSTEM 2. DRIVING PRECAUTIONS (WITH REAR VIEW MONITOR GUIDE LINES) In any of the following situations, there is a margin of error between the guide lines on the screen and the actual dis- tance/course on the road. When the grade behind the vehicle slopes down sharply, objects appear to be closer than they actually are.
Page 119 1. REAR VIEW MONITOR SYSTEM Approx. 1.5 ft. (0.5 m) The distance that appears on the screen between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as fol- lows. • In reality, <...
Page 120 1. REAR VIEW MONITOR SYSTEM...
Page 121 1. BASIC INFORMATION BEFORE OPERATION Introduction DISPLAY AUDIO SYSTEM OWNER’S MANUAL This manual explains the operation of the Display Audio system. Please read this manual carefully to ensure proper use. Keep this manual in your vehicle at all times. The screen shots in this document and the actual screens of the Display Audio system differ depending on whether the functions and/or a contract existed and the map data available at the time of producing this document.
Page 122 1. BASIC INFORMATION BEFORE OPERATION IMPORTANT INFORMATION ABOUT THIS MANUAL For safety reasons, this manual indicates items requiring particular attention with the following marks. CAUTION ● This is a warning against anything which may cause injury to people if the warning is ignored.
Page 123 1. BASIC INFORMATION BEFORE OPERATION SAFETY INSTRUCTION CAUTION ● For safety, the driver should not operate the Display Audio system while he/she is driving. Insufficient attention to the road and traffic may cause an accident. While driving, be sure to obey the traffic ●...
Page 124 1. BASIC INFORMATION BEFORE OPERATION...
Page 125 1. CONTROLS AND FEATURES 1. OVERVIEW BUTTONS The actual design and button position may differ depending on the vehicle. For details, see Section 3 of “Owner’s Manual”. Name Function Page Touch screen By touching the screen with your finger, you can display control the selected functions.
Page 126 1. CONTROLS AND FEATURES Name Function Page 107, 114, “SEEK/TRACK” Press the “ ” or “ ” button to seek up or down for 119, 121, button a radio station, or to access a desired track or file. 124, 137 Press this button to access the vehicle informa- “CAR”...
Page 127 1. CONTROLS AND FEATURES 2. SYSTEM FUNCTION INDEX ® APPLICATION SYSTEM Bluetooth HANDS-FREE SYSTEM To access the application system, press the “APPS” button. The “Applications” ® To access the Bluetooth hands-free sys- menu screen will be displayed. The driver tem, press the button.
Page 128 1. CONTROLS AND FEATURES VEHICLE INFORMATION REAR VIEW MONITOR SYSTEM (IF EQUIPPED) Shifting into the “R” position will automati- cally show the view behind the rear of the To access the vehicle information system, vehicle on the display screen. For details, press the “CAR”...
Page 129 1. CONTROLS AND FEATURES 3. TOUCH SCREEN OPERATION This system is operated mainly by the INPUT SCREEN OPERATION screen buttons on the screen. When searching for an address or a To prevent damage to the screen, lightly name, letters and numbers can be in- touch screen buttons on the screen with the finger.
Page 130 1. CONTROLS AND FEATURES ■ INPUTTING SYMBOLS Touch ■ CHANGING BETWEEN LOWER CASE AND UPPER CASE Touch Touch ) or : Touch to enter in lower case. ) keyboard layout : Touch to enter in upper case. Each time is touched, input will change between upper case and lower case input.
Page 131 1. CONTROLS AND FEATURES ENTERING FROM THE LIST OF LIST SCREEN OPERATION MATCHING ENTRIES When a list is displayed, use the appro- On certain screens, a candidate entry priate screen button to scroll through text or word prediction list based on the the list.
Page 132 1. CONTROLS AND FEATURES CHARACTER JUMP BUTTONS IN LISTS Some lists contain character screen buttons, “ABC”, “DEF” etc., which al- low a direct jump to list entries that be- gin with the same letter as the character screen button. Touch one of the character screen but- tons.
Page 133 1. NAVIGATION OPERATION 1. QUICK REFERENCE The navigation application and several other applications can be accessed by pressing the “APPS” button. When the “APPS” button is pressed, the “Applications” menu screen that was last displayed is returned to. Touch to display the “Applications” menu screen. “Applications”...
Page 134 1. NAVIGATION OPERATION To display the “Navigation” menu screen, touch “Dest” on the map. From this screen, destinations can be entered and route-related settings can be changed. “Navigation” menu screen Function Page Touch to display the “My Destinations” screen. A destination can be entered by selecting an item from the list of stored destinations, previous destinations or the addresses from the connect- ed phone’s phone book.
Page 135 1. NAVIGATION OPERATION Overview guidance screen Function Page This symbol indicates a map layout. Touching this symbol changes the map layout. Displays the distance, the estimated travel time to the destination, or the estimated arrival time at the destination. Displays traffic information on the route. Displays the distance to the next turn with the arrow indicating the turn direction.
Page 136 1. NAVIGATION OPERATION 2. NAVIGATION SYSTEM FUNCTION INDEX Displaying maps Page Viewing the map screen Displaying the current vehicle position Viewing the current vehicle position vicinity map Changing the scale Changing the map layout Displaying Point of Interest Icons Viewing traffic messages Searching destination Page Searching the destination...
Page 137 1. NAVIGATION OPERATION During route guidance Page Stopping route guidance Adjusting route guidance volume Displaying the entire route map Memory point Memory point Page Registering the entry Editing the entry Loading the entry from external devices...
Page 138 1. NAVIGATION OPERATION 3. MAP SCREEN OPERATION TO DISPLAY MAP SCREEN INFORMATION ● The “CAUTION” screen will be displayed Press the “APPS” button. when the screen is changed to the map screen for the first time after the engine switch has been in the “ACC” or “ON” position.
Page 139 1. NAVIGATION OPERATION ■ CURRENT LOCATION AND GPS IN- INFORMATION FORMATION ● The vehicle icon can be changed. (See page 61.) Current location, geo-coordinates and While driving, the current vehicle posi- ● GPS information are displayed. tion mark is fixed on the screen and the map moves.
Page 140 1. NAVIGATION OPERATION SCREEN SCROLL OPERATION MAP CONFIGURATIONS When any point on the map is touched, Any of the following map configura- that point moves to the center of the tions can be selected. screen and is shown by the cursor ■...
Page 141 1. NAVIGATION OPERATION 3D Heading ■ MAP LAYOUT The map layout can be changed from “3D Heading”, “2D Heading” or “2D North”. Touch 2D Heading Touch the desired map layout. 2D North “3D Heading”: Touch to display 3D map. The direction of vehicle travel is always up. “2D Heading”: Touch to display 2D map.
Page 142 1. NAVIGATION OPERATION 4. MAP ICONS POI ICONS Icon Name Court house DISPLAY POI ICONS Place of worship Points of Interest such as gas stations and restaurants can be displayed on the map screen. Their location can Accommodation, Hotel/Motel also be set as a destination. POI icons are displayed on the map.
Page 143 1. NAVIGATION OPERATION Traffic Icon Name Icon Name Motorcycle Dealer Car Dealer/Repairer, Repair Fa- cility, Repair General, Car Wash, Clubbing Tire Repair Icon Name Car Dealer Multiple POI Highway Exit Bar, Nightlife Airport, Dep. /Arrival, Ground, In- ternational, Domestic Leisure, Cultural Center, The- ater, Music Center, Concert Hall Bus Terminal, Bus Stop, Trans- portation, Public Transp.
Page 144 1. NAVIGATION OPERATION Leisure Icon Name Icon Name Clothing Amusement Park Cleaning & Laundry Winery Museum Shopping, Market Place, Shop- ping Center, Factory Outlet Shop, Department Store, Drive- through-bottle-shop Tourist Attractions, Important Tourist Attractions Park/Recreational Area Yacht Basin, Harbour Camping Ground Grocery Store Historical Monument RV Park, Camping...
Page 145 1. NAVIGATION OPERATION DISPLAYING POI INFORMATION Touch the desired POI icon on the map. Touch One POI Multiple POI POI information will be displayed. When “Calculate” is touched, the start- ing route guidance screen is displayed. (See page 42.) When “Save” is touched, the point is registered in the “Stored”...
Page 146 2. DESTINATION SEARCH 1. DESTINATION SEARCH DESTINATION SEARCH BY DESTINATION SEARCH ON “Stored” THE “My Destinations” SCREEN Destinations can be selected from the destinations registered with the sys- There are several ways to search a tem. To use this function, it is neces- destination.
Page 147 2. DESTINATION SEARCH DESTINATION SEARCH BY DESTINATION SEARCH BY “Previous” “Phone Book” A destination can be selected from the A destination can be set using the past destination list. address of a contact from the phone book of a connected cellular phone. Touch “Previous”...
Page 148 2. DESTINATION SEARCH DESTINATION SEARCH BY DESTINATION SEARCH ON “Address” THE “Enter Destination” SCREEN A destination can be searched using a city name or zip code. There are several ways to search a destination. Touch “Address” on the “Enter Desti- nation”...
Page 149 2. DESTINATION SEARCH Touch “City” or “Zip” to enter the city DESTINATION SEARCH BY name or zip code. “POI” POIs in a specific area can be searched by category, name or from the map. ■ SEARCHING “By Category” Touch “POI” on the “Enter Destina- tion”...
Page 150 2. DESTINATION SEARCH ■ SEARCHING “By Name” Touch for the desired item. Touch “POI” on the “Enter Destina- tion” screen. Touch “By Name” on the “POI” screen. Touch the desired item to search the area. (See page 38.) Input POI name. If you touch the desired item, the starting route guidance screen will be displayed (See page 42.)
Page 151 2. DESTINATION SEARCH ■ ■ SELECTING “By Map” SELECTING THE SEARCH AREA Touch “POI” on the “Enter Destina- Touch “By Category”, “By Name” or tion” screen. “By Map”. Touch “By Map” on the “POI” screen. Touch the desired item to search the area.
Page 152 2. DESTINATION SEARCH Selecting “Around” area ■ ONLINE SEARCH If you select “Around”, touch “De- A destination can be selected via En- fine” to select the desired search area. tune service. For detailed information about “Online Search”, see page 83. Touch “Country”...
Page 153 2. DESTINATION SEARCH ■ SELECTING ON MAP DESTINATION SEARCH BY “Advanced” Touch “Select Point on Map” on the “Advanced” screen. Touch “Advanced” on the “Enter Des- tination” screen. Touch the desired point on the map. Touch the desired method to search the destination.
Page 154 2. DESTINATION SEARCH ■ ENTER GEO-COORDINATES INFORMATION ● If a destination that is not located on a Geo coordinates can be entered in road is set, the vehicle will be guided to DMS format (Degrees , Minutes’, Sec- the point on a road nearest to the desti- onds”).
Page 155: Starting Route Guidance
3. ROUTE GUIDANCE 1. STARTING ROUTE GUIDANCE STARTING ROUTE INFORMATION GUIDANCE SCREEN ● The default recommended route can be changed. (See pages 43 and 64.) The arrival time or the remaining time ● After searching the destination, the will be displayed in the upper right area starting route guidance screen will be of the map.
Page 156 3. ROUTE GUIDANCE SETTING THE AVOIDANCE SETTING THE ROUTE CRITERIA SETTING THE ROUTE Touch “Avoid” on the starting route PREFERENCES guidance screen. Touch the desired item. Touch “Preferences” on the starting route guidance screen. Touch the desired item. “Avoid Freeways”: Touch to avoid freeways.
Page 157: Route Guidance
3. ROUTE GUIDANCE 2. ROUTE GUIDANCE ■ SIGNPOSTS ROUTE GUIDANCE SCREEN When approaching the turn, a signpost While guiding the route, the following will automatically be displayed. screen will be displayed. ■ LANE RECOMMENDATION On this screen, the following information is displayed.
Page 158 3. ROUTE GUIDANCE VOICE GUIDANCE CAUTION ● Be sure to obey the traffic regulations The voice guidance provides various and keep the road condition in mind messages as you approach an inter- especially when you are driving on IPD section, or other points where maneu- roads.
Page 159 3. ROUTE GUIDANCE 3. SETTING AND DELETING THE ROUTE Routes can be checked, changed and Function recalculated during route guidance. Touch to change the map setting. (See page 61.) SETTING FROM THE Touch to stop the current route guid- “Options” SCREEN ance.
Page 160 3. ROUTE GUIDANCE SETTING THE ROUTE DISPLAYING THE ROUTE LIST PREFERENCE OR AVOIDANCE A list of the different segments of the CRITERIA route can be displayed. Touch “Route Options For Current Touch “Route List” on the “Options” Route” on the “Options” screen. screen.
Page 161 3. ROUTE GUIDANCE BLOCK ROAD AHEAD DISPLAYING THE DESTINATION INFORMATION A fixed distance on the road ahead can be blocked. The destination information is dis- played. Touch “Block Road Ahead” on the Touch “Destination Information” on “Options” screen. the “Options” screen. Touch the desired item to select the The destination information screen will desired detour distance.
Page 162 3. ROUTE GUIDANCE If you search the destination by “Enter ADDING DESTINATIONS Address” Touch “Add as Waypoint”. Destinations can be added and the route changed accordingly. If you search the destination by “Select Point on Map” or “Enter Geo-coordi- Touch “Dest” on the map. nates”...
Page 163 3. ROUTE GUIDANCE On this screen, the following functions can EDITING DESTINATIONS be operated. Touch “Show Destination List” on Function the “Waypoint” screen. Touch to register the point in the “Stored” list on the “My Destina- tions” screen. (See page 55.) Touch to change the order of the destinations.
Page 164 3. ROUTE GUIDANCE CANCELLING THE DETOURED DETOURING A SEGMENT ON SEGMENT THE ROUTE Display the route list. (See page 47.) When detouring a segment, the detour route can be changed. Touch “Detours”. DETOURING THE SEGMENT Display the route list. (See page 47.) Touch the desired segment to detour.
Page 165 4. MY DESTINATIONS 1. REGISTERING A ENTRY Input the entry address. (See page 35.) REGISTERING A NEW ENTRY Up to 200 destinations can be regis- tered with this system. INFORMATION This function cannot be operated while ● driving. Touch “Save New Entry”. REGISTERING FROM THE “My Input the entry name.
Page 166 4. MY DESTINATIONS If you search the destination by “Enter ■ REGISTERING “Home” Address” If “Home” has not been registered, Touch “Save as Home Address”. touching “Home” allows a home ad- If you search the destination by “Select dress to be registered. Point on Map”...
Page 167 4. MY DESTINATIONS REGISTERING FROM THE MAP REGISTERING FROM THE LIST Touch the desired point on the map. ■ REGISTERING FROM THE LIST ON THE “Previous” OR “Phone Book” Touch “Save”. SCREEN Search the point by “Previous” or “Phone Book”. (See pages 34 and 34.) Touch next to the desired item.
Page 168 4. MY DESTINATIONS ■ REGISTERING FROM THE DESTI- REGISTERING FROM GEO- NATION LIST COORDINATES Display the “Show Destination List” Search the point by “Enter Geo-coor- screen. (See page 50.) dinates”. (See page 41.) Touch the desired destination. Touch “Save”. Touch “Add to Stored Destinations”. Follow the steps “REGISTERING FROM “My...
Page 169 4. MY DESTINATIONS Touch “Advanced” on the “Enter Des- REGISTERING FROM AN tination” screen. EXTERNAL DEVICE Touch “Load Contacts from USB”. “vCard” formatted data can be trans- ferred from a USB memory to this sys- tem. Transferred addresses numbers will be stored in the “Stored” list on the “My Destinations”...
Page 170 4. MY DESTINATIONS INFORMATION ● If a message similar to the one below is displayed, delete X item(s) in the “Stored” list on the “My Destinations” screen and “Contacts” screen to make room for the new destination(s). (See pages 58 and 168.) ■...
Page 171 4. MY DESTINATIONS 2. DISPLAYING AND EDITING THE ENTRY INFORMATION The entry options screen of “Phone DISPLAYING AND EDITING Book” list THE ENTRY INFORMATION Detailed information of entries in the list can be displayed or edited. Touch next to the desired item on the “My Destinations”...
Page 172 4. MY DESTINATIONS SHOW DETAILS OF THE EDITING THE ADDRESS ENTRY Touch “Edit Address” on the entry Touch “Show Details” on the entry options screen. options screen. Input the new address. (See page 35.) This screen will be displayed. Touch “Save Changes”. The address will be marked on the map.
Page 173 4. MY DESTINATIONS 3. SENDING STORED CONTACTS TO A USB MEMORY Touch “General”. SENDING STORED CONTACTS TO A USB MEMORY The entries stored in the “Stored” list on the “My Destinations” screen and “Contacts” screen (See pages 52 and 165.) can be transferred to a USB memory.
Page 174: Map Settings
5. NAVIGATION SETTING 1. MAP SETTINGS On this screen, the following functions can SETTING THE MAP be set. Touch “Options”. Function Touch to change the map layout. (See page 28.) Touch to set the display of POI icon categories. (See page 62.) Touch to change the vehicle icon.
Page 175 5. NAVIGATION SETTING POIS ON MAP VEHICLE ICONS POI categories displayed on the map The vehicle icon can be changed. can be selected. Touch “Vehicle Icons” on the “Map Touch “POIs on Map” on the “Map Settings” screen. Settings” screen. Touch the desired icon.
Page 176 5. NAVIGATION SETTING DAY/NIGHT MODE ARRIVAL INFORMATION The screen can be changed to day The estimated time to the destination mode or night mode. can be changed between arrival time/ distance and remaining time/distance. Touch “Day/Night Mode” on the “Map It can also be turned off.
Page 177: Route Settings
5. NAVIGATION SETTING 2. ROUTE SETTINGS “Route Type”: Touch to select the route SETTING THE ROUTE type between “Fast Route”, “Short OPTIONS Route” and “Ecological Route”. “Show Route Alternatives”: Touch to display 3 routes (fastest, shortest and eco- SETTING THE ROUTE logical) on the map after a route calcula- CALCULATION tion.
Page 178 5. NAVIGATION SETTING SETTING THE AVOIDANCE CRITERIA FOR THE ROUTE CALCULATION The avoidance criteria for the route cal- culation can be set. Touch “Dest” on the map. Touch “Route Options”. The “Route Options” screen can be dis- played by touching on any of the “Navigation”...
Page 179 6. NAVIGATION SYSTEM INFORMATION 1. LIMITATIONS OF THE NAVIGATION SYSTEM Even when the navigation system is re- This navigation system calculates the ceiving clear GPS signals, the vehicle po- current vehicle position using satellite sition may not be shown accurately or signals, various vehicle signals, map inappropriate route guidance may occur in data, etc.
Page 180 6. NAVIGATION SYSTEM INFORMATION Inappropriate route guidance may occur in the following cases: • When turning at an intersection off the designated route guidance. • If you set more than one destination but skip one of them, auto reroute will dis- play a route returning to the destination that was skipped.
Page 181 6. NAVIGATION SYSTEM INFORMATION 2. MAP INFORMATION END-USER TERMS TERMS AND CONDITIONS The data (“Data”) is provided for your PLEASE READ THIS END USER personal, internal use only and not for LICENSE AGREEMENT resale. It is protected by copyright, and CAREFULLY BEFORE USING THE is subject to the following terms and NAVTEQ DATABASE...
Page 182 6. NAVIGATION SYSTEM INFORMATION LICENSE GRANT LIMITED WARRANTY NAVTEQ grants you a non-exclusive NAVTEQ warrants that, subject to the license to use the Database for your warnings set out below, for a period of personal use or, if applicable, for use in 12 months after acquisition of your your business’...
Page 183 6. NAVIGATION SYSTEM INFORMATION If you did not acquire the Database WARNINGS from NAVTEQ directly, you may have The Database may contain inaccurate statutory rights against the person from or incomplete information due to the whom you have acquired the Database passage time, changing...
Page 184 6. NAVIGATION SYSTEM INFORMATION...
Page 185 6. NAVIGATION SYSTEM INFORMATION...
Page 186 1. APPLICATIONS OPERATION 1. QUICK REFERENCE The navigation application and several other applications can be accessed by pressing the “APPS” button. When the “APPS” button is pressed, the “Applications” menu screen that was last displayed is returned to. Touch to display the “Applications” menu screen. “Applications”...
Page 187 1. APPLICATIONS OPERATION 2. PICTURE SLIDESHOW Press the “APPS” button to display When the vehicle is stopped, pictures the “Applications” menu screen. stored on a USB memory can be viewed. If the “Applications” menu screen is not INFORMATION ● Images cannot be viewed while driving. displayed, touch until it is dis- played.
Page 188 1. APPLICATIONS OPERATION PLAYING PICTURE SLIDESHOWS A slideshow can be played, paused, and desired images can be selected. Touch “Show”. Operating switches will be displayed. “Hide”: Touch to close the slideshow op- tions. : Touch to pause the slideshow. : Touch to play the slideshow again.
Page 189 1. APPLICATIONS OPERATION 3. EMAIL Incoming Emails to a connected CHECKING “Email” ® Bluetooth capable phone can be downloaded. Before using this Press the “APPS” button to display ® the “Applications” menu screen. application, connect the Bluetooth phone with phone profile. (See page 203.) If the “Applications”...
Page 190 1. APPLICATIONS OPERATION The state of Email is shown by the follow- ing icons. : Unread mail : Read mail : Important mail The text of the Email is displayed. : Touch to have the Email read out. To cancel this function, touch NOTICE ●...
Page 191 1. APPLICATIONS OPERATION 4. CALENDAR When the downloading of the calendar is Calendar entries, tasks and notes from complete, the current day’s calendar ® connected Bluetooth capable entries will be displayed. phone can be downloaded. Before When a displayed schedule entry is using this application, connect the touched, the entry’s detailed informa- ®...
Page 192 “OK”. Touch “enTune Password”. USER REGISTRATION When purchasing the vehicle, an email address is registered at your Toyota dealer. If your email address was not registered at your Toyota dealer, your email address can be registered at the Entune website. A user registration guidance email containing a web ad- dress will be sent.
Page 193 REGISTERING THE INFORMATION DOWNLOADED ENTUNE ● If your email address was not registered APPLICATION at your Toyota dealer when the vehicle was purchased, an email address can Download the Entune application using be registered at http://www.toyota.com/ entune/. your cellular phone.
Page 194 Entune are explained. INFORMATION For details regarding Entune operations Once initialized, data will be erased. Pay ● and each of the application, refer to close attention when initializing the data. http://www.toyota.com/entune/.
Page 195 2. ENTUNE SERVICE 2. OPERATING NAVIGATION FUNCTION USING ENTUNE SERVICE ONLINE SEARCH A destination can be selected via on- line search. Before using this function, connect a ® Bluetooth phone with an internet pro- file. (See page 203.) When the cost warning or roaming warn- Touch “Dest”...
Page 196 2. ENTUNE SERVICE Touch “Enter Search Word”. The starting route guidance screen will be displayed. (See page 42.) Input the search word and then touch “OK”. INFORMATION The color of indicates if online con- ● nection is active or not. After a timeout of 1 minute, an active online connection will automatically be terminated.
Page 197 2. ENTUNE SERVICE FUEL PRICES Touch for the desired item. It enables the navigation system to dis- play current fuel prices and gas station locations, which can be set as a desti- nation if desired. Before using this function, connect a ®...
Page 198 2. ENTUNE SERVICE Touch “On Route”, “Show All” or TRAFFIC MESSAGES “Warnings” to select the desired list. It contains a list of traffic messages re- lating to the set route, all traffic mes- sages and warnings. Before using this function, connect a ®...
Page 199 2. ENTUNE SERVICE On this screen, the following information is ■ LIST TRAFFIC MESSAGE displayed. ICONS Information Icon Name Street number Slippery Route segment If route segment is not available, Bad weather information such as street name, city name, region or country will be displayed.
Page 200 2. ENTUNE SERVICE The route will be recalculated. DETOURING A SEGMENT FROM A TRAFFIC MESSAGE The mark of the TMC on the “On Route” LIST screen changes into If a traffic message relates to the route ■ CANCELLING DETOURED being travelled, the desired segment SEGMENT can be detoured.
Page 201 2. ENTUNE SERVICE If “Consider” is selected RECALCULATING THE ROUTE BY THE TRAFFIC MESSAGES Touch “Ignore” or “Detour”. You will be informed about relevant traffic messages on the route by a pop- up window. A pop-up window may differ depending on the traffic message settings.
Page 202 2. ENTUNE SERVICE ■ SETTING “Radius Filter” TRAFFIC MESSAGE SETTINGS Once the radius filter has been set, Touch “Dest” on the map. only traffic messages within the radius Touch “Route Options”. will be displayed in the traffic message list. Touch “Radius Filter” on the “Set- tings”...
Page 203 2. ENTUNE SERVICE ■ SETTING “Dynamic Reroute” LOADING ADDRESSES FROM A PHONE The method of reroute can be set. Touch “Dynamic Reroute” on the Addresses and numbers will be stored “Settings” screen. in the “Stored” list on the “My Destina- tions”...
Page 204 2. ENTUNE SERVICE When the cost warning or roaming warn- INFORMATION ing screen is displayed, touch “Con- tinue”. This function can be set to on or ● If a message similar to the one below is off. (See page 208.) displayed, delete X item(s) in the “Stored”...
Page 205 2. ENTUNE SERVICE 3. OPERATING AN APPLICATION USING ENTUNE SERVICE When the cost warning or roaming warn- OPERATING AN ing screen is displayed, touch “Con- APPLICATION tinue”. This function can be set to on or off. (See page 208.) Several downloaded applications can be Before using applications, connect the opened at the same time and the desired ®...
Page 206 2. ENTUNE SERVICE DELETING AN APPLICATION Touch Touch “Delete” on the right side of the application to be deleted. Applications that displayed “Delete” on the right side of the application can be removed. The following confirmation screen will be displayed. Touch “Yes”.
Page 207 The cellular phone cannot be www.toyota.com/entune/ assistance, please visit connected. confirm phone toyota.com or call 1-800-331- compatible or not. 4331.” “This feature is unavailable hands-free call After the hands-free call is fin- during a handsfree call.” progress. ished, perform the operation.
Page 208 2. ENTUNE SERVICE...
Page 209 APPLICATION-THE OTHERS...
Page 210 1. AUDIO SYSTEM OPERATION 1. QUICK REFERENCE To access the audio system, press the “AUDIO” button. The audio system turns on in the last mode used. The actual design and button position may differ depending on the vehicle. For details, see Section 3 of “Owner’s Manual”. Name Function Page...
Page 211 1. AUDIO SYSTEM OPERATION Name Function Page 107, 114, “SEEK/TRACK” Press the “ ” or “ ” button to seek up or down for 119, 121, button a station, or to access a desired track or file. 124, 137 Press to turn the audio system on and off, and “PWR VOL”...
Page 212 1. AUDIO SYSTEM OPERATION 2. SOME BASICS This section describes some of the ba- TURNING THE AUDIO sic features of the audio system. Some SYSTEM ON OR OFF information may not pertain to your system. Your audio system works when the en- gine switch is turned to the “ACC”...
Page 213 1. AUDIO SYSTEM OPERATION CONTROLS USING THE SWITCHING AUDIO SOURCE “TUNE SCROLL” KNOB Press the “AUDIO” button. Radio mode Radio stations can be tuned in manually using this knob. Modes other than radio Tracks, songs or files can be selected us- ing the knob.
Page 214 1. AUDIO SYSTEM OPERATION With JBL sound system DSP CONTROL Press the “AUDIO” button. Touch ® USB memory/iPod and Bluetooth dio modes Touch the desired screen button. AUTOMATIC SOUND LEVELIZER (ASL) The system adjusts to the optimum vol- ume and tone quality according to ve- hicle speed compensate...
Page 215 1. AUDIO SYSTEM OPERATION Modes other than USB memory/iPod TONE AND BALANCE ® and Bluetooth audio TONE How good an audio program sounds is largely determined by the mix of the treble, mid and bass levels. In fact, dif- ferent kinds of music and vocal pro- grams usually sound better with different mixes of treble, mid and bass.
Page 216: Radio Operation
1. AUDIO SYSTEM OPERATION 3. RADIO OPERATION SWITCHING TO RADIO MODE PRESETTING A STATION Press the “AUDIO” button. Radio mode has a mix preset function, which can store up to 36 stations (6 station per page 6 page) from any of the AM, FM or SAT bands.
Page 217 1. AUDIO SYSTEM OPERATION SELECTING A STATION RADIO BROADCAST DATA SYSTEM Tune in the desired station using one of the following methods. This audio system is equipped with Ra- dio Broadcast Data Systems (RBDS). Preset tuning: Touch one of the mix pre- RBDS mode allows text messages to set channels on the left side of the screen be received from radio stations that uti-...
Page 218 1. AUDIO SYSTEM OPERATION Touch “TYPE >” or “< TYPE” to move TRAFFIC ANNOUNCEMENT forward and backward through the pro- gram list. A station that regularly broadcasts traf- fic information is automatically located. Once a program type has been set, “TYPE SEEK”...
Page 219 1. AUDIO SYSTEM OPERATION INFORMATION USING HD Radio™ TECHNOLOGY Touch “Text”. HD Radio™ Technology is the digital evolution of analog AM/FM radio. Your radio product has a special receiver which allows it to receive digital broadcasts (where available) addition to the analog broadcasts it already receives.
Page 220 1. AUDIO SYSTEM OPERATION INFORMATION ● If tagging the music information fails, Touch “Tag” to bookmark the music “Saving the HD Radio tag failed.” will be information. displayed on the screen. If this occurs, tag the information again. ● HD Radio™ stations can be preset. Open the cover and connect iPod us- ing an iPod cable.
Page 221 1. AUDIO SYSTEM OPERATION TROUBLESHOOTING GUIDE Experience Cause Action Mismatch of time alignment The radio stations analog a users may hear a short and digital volume is not None, radio broadcast issue. A period of programming re- properly aligned or the sta- user can contact the radio station.
Page 222 Canadian provinces. SATELLITE TUNER HOW TO SUBSCRIBE TECHNOLOGY NOTICE It is necessary to enter into a separate Toyota’s satellite radio tuners are ® service agreement with XM Satellite awarded Type Approval Certificates Radio in order to receive satellite ®...
Page 223 1. AUDIO SYSTEM OPERATION SWITCHING TO SATELLITE CHANNEL CATEGORY RADIO MODE Touch “Options”. Press the “AUDIO” button to display the audio control screen. Touch either “TYPE >” or “< TYPE” to go to the next or previous category. The audio system turns on in the last mode used.
Page 224 1. AUDIO SYSTEM OPERATION SELECTING A CHANNEL DISPLAYING THE TITLE AND NAME Tune in the desired channel using one of the following methods. Touching “Text” displays the artist name and song title you are currently Preset tuning: Touch the channel selector listening to.
Page 225 Check whether the XM tenna cable is attached securely. Ck Antenna A short circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer for assistance. ® You have not subscribed to XM Satellite Radio. The radio is be- ®...
Page 226 1. AUDIO SYSTEM OPERATION NOTICE ● This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation.
Page 227 1. AUDIO SYSTEM OPERATION 5. CD PLAYER OPERATION The CD player can play audio CDs, CD text and MP3/WMA discs. (a)Audio CD, CD text (see page 118) (b)MP3/WMA disc (see page 120) For appropriate discs for this player, see “AUDIO SYSTEM OPERATING HINTS”...
Page 228 1. AUDIO SYSTEM OPERATION SWITCHING TO CD MODE PLAYING AN AUDIO CD Press the “AUDIO” button. If a CD-TEXT disc is inserted, the title of the track and disc currently being played will be displayed. : Touch to pause the track. The audio system turns on in the last mode used.
Page 229 1. AUDIO SYSTEM OPERATION SELECTING A DESIRED TRACK Select a desired track using one of the following methods. Touch a desired track. The player will start playing the selected track from the begin- ning. Touch to scroll the list. appears to the right of titles, the complete titles are too long for the display.
Page 230 1. AUDIO SYSTEM OPERATION PLAYING REPEAT AND PLAYING A MP3/WMA DISC RANDOM ORDER The title of the file and folder currently being played will be displayed. (Repeat mode): Use it to automat- ically repeat the track you are currently lis- : Touch to pause the file.
Page 231 1. AUDIO SYSTEM OPERATION Touch a desired file. The player will start SELECTING A DESIRED FILE playing the selected file from the begin- ning. Select a desired file using one of the Touch to scroll the list. following methods. appears to the right of titles, the complete titles are too long for the display.
Page 232 1. AUDIO SYSTEM OPERATION PLAYING REPEAT AND RANDOM ORDER (Repeat mode): Use it to automat- ically repeat the file or folder you are cur- rently listening to. The repeat mode changes as follows each time the screen button is touched. :Repeating the file :Repeating the folder :OFF...
Page 233 1. AUDIO SYSTEM OPERATION 6. USB MEMORY/iPod OPERATION The system enables users to enjoy CONNECTING A USB music played from a USB memory or MEMORY OR iPod iPod on the vehicle's speakers. Open the cover of the USB/AUX port CAUTION and connect a USB memory or iPod using an iPod cable.
Page 234 1. AUDIO SYSTEM OPERATION SWITCHING TO USB OR iPod PLAYING A USB MEMORY OR MODE iPod Press the “AUDIO” button. PLAYING A SONG The title of the album, song and artist name of the song currently being lis- tened to will be displayed. ■...
Page 235 1. AUDIO SYSTEM OPERATION ■ FAST FORWARD AND REVERSE SELECTING A DESIRED SONG Press and hold the “ ” or “ ” of the ■ SELECTING A PLAYLIST “SEEK/TRACK” button to fast forward or reverse. When the button is re- Songs can be sorted and selected from leased, the player will start playing various playlists.
Page 236 1. AUDIO SYSTEM OPERATION ■ SELECTING A DESIRED SONG US- INFORMATION ING “SEEK/TRACK” BUTTON OR ● USB memory only: Files that do not con- “TUNE SCROLL” KNOB tain song title and/or album information will be displayed as “Unknown” in the “Artist”...
Page 237 1. AUDIO SYSTEM OPERATION COVER ART FUNCTION PLAYING “PLAY MORE LIKE THIS” FUNCTION The album, that the song currently be- ing listened to is from, is called up so The system creates a new playlist con- taining songs similar to the one cur- that a song from it can be selected.
Page 238 1. AUDIO SYSTEM OPERATION Touch “Play More Like This Set- REPEAT AND RANDOM PLAY tings”. FUNCTIONS Repeat and random play functions are available. ■ FROM AUDIO CONTROL SCREEN Touch Touch the desired size of the playlist. (Repeat mode): Use it to automatical- ly repeat the song you are currently listen- Touch ing to.
Page 239 1. AUDIO SYSTEM OPERATION ■ FROM THE “Options” SCREEN Touch “Options”. Touch “Random” or “Repeat Track”. To cancel repeat or random order, touch “Random” or “Repeat Track” again. INFORMATION When “Random” is on, the songs in the ● current playlist can be played in random order.
Page 240 1. AUDIO SYSTEM OPERATION 7. AUX DEVICE OPERATION Connecting a portable audio device CONNECTING A PORTABLE with the AUX port enables users to en- AUDIO DEVICE joy music via the vehicle speakers. Open the cover of the USB/AUX port CAUTION and connect a portable audio device.
Page 241 1. AUDIO SYSTEM OPERATION SWITCHING TO AUX MODE PLAYING A PORTABLE AUDIO DEVICE Press the “AUDIO” button. Only the volume can be adjusted using the audio system controls. The remaining controls need to be operated on the porta- The audio system turns on in the last ble audio device itself.
Page 242 1. AUDIO SYSTEM OPERATION ® 8. Bluetooth AUDIO OPERATION ® The Bluetooth audio system enables users to enjoy music played on a por- table player from the vehicle speaker via wireless communication. Bluetooth is a registered trademark of If your portable player does not support Bluetooth SIG, Inc.
Page 243 1. AUDIO SYSTEM OPERATION ® SWITCHING TO Bluetooth CAUTION AUDIO MODE ● FCC WARNING: Changes or modifica- tions not expressly approved by the Press the “AUDIO” button. party responsible for compliance could void the user’s authority to operate the equipment. ●...
Page 244 1. AUDIO SYSTEM OPERATION ® ® CONNECTING Bluetooth CONNECTING Bluetooth AUDIO AUDIO ■ CONNECTING FROM THE SYSTEM ® In order to use the Bluetooth audio ® Switching to Bluetooth audio mode. system, it is necessary to pair a porta- (See page 133.) ble player and connect the audio pro- file (A2DP) with the system.
Page 245 1. AUDIO SYSTEM OPERATION The following screen will be displayed The following screen will be displayed ® when pairing is complete. while searching for a Bluetooth vice. The system waits for connection re- To cancel this function, touch “Cancel”. quests coming from the paired device. All requested profiles are connected Touch the device to be paired.
Page 246 1. AUDIO SYSTEM OPERATION ■ CONNECTING FROM THE DEVICE Confirm the PIN. ® If the device supports SSP (Secure Sim- Switching to Bluetooth audio mode. ple Pairing) (See page 133.) Confirm the PIN displayed on the screen, Touch “Search Bluetooth Devices”. and then touch “Accept”.
Page 247 1. AUDIO SYSTEM OPERATION ® ® RECONNECTING Bluetooth PLAYING Bluetooth AUDIO AUDIO PLAYING A SONG If a portable player is disconnected due ® to poor reception from the Bluetooth The title of the song, album and artist network when the engine switch is in name of the song currently being lis- the “ACC”...
Page 248 1. AUDIO SYSTEM OPERATION ■ FAST FORWARD AND REVERSE The selecting playlist screen is can be displayed from the “Options” screen. Press and hold the “ ” or “ ” of the Touch “Options” then touch “SEEK/TRACK” button to fast forward “Browse For Music”...
Page 249 1. AUDIO SYSTEM OPERATION ■ ■ SELECTING BY LIST SELECTING A DESIRED SONG US- ING “SEEK/TRACK” BUTTON OR The desired song can be selected from “TUNE SCROLL” KNOB the current playlist. Touch “List”. “SEEK/TRACK” button: Press the “ ” or Touch the desired song.
Page 250 1. AUDIO SYSTEM OPERATION ■ FROM THE “Options” SCREEN REPEAT AND RANDOM PLAY FUNCTIONS Touch “Options”. Repeat and random play functions are available. ■ FROM AUDIO CONTROL SCREEN Touch Touch “Random” or “Repeat Track”. (Repeat mode): Use it to automatical- ly repeat the song you are currently listen- To cancel repeat or random order, touch ing to.
Page 251 1. AUDIO SYSTEM OPERATION 9. STEERING SWITCHES Some parts of the audio system can be “ ” “ ” switch adjusted with the switches on the Radio steering wheel. To select a preset station: Press the “ ” switch. or “ ” STEERING SWITCHES (WITH To seek a radio station: Press and hold TWO DIRECTION STEERING...
Page 252 1. AUDIO SYSTEM OPERATION To seek a station: Press and hold the “ ” STEERING SWITCHES (WITH or “ ” side of the switch until a beep is FOUR DIRECTION STEERING heard. Repeat this to find the next station. SWITCH) If either side of the switch is pressed dur- ing seek mode, seeking will be canceled.
Page 253 1. AUDIO SYSTEM OPERATION “MODE/HOLD” switch Press the “MODE/HOLD” switch to select an audio mode. Each press changes the mode sequentially if the desired mode is ready to use. To turn the audio system on, press the “MODE/HOLD” switch. Press and hold the “MODE/HOLD” switch until you hear a beep and the music will pause or be muted.
Page 254 1. AUDIO SYSTEM OPERATION 10. AUDIO SYSTEM OPERATING HINTS NOTICE Fading and drifting stations: Generally, ● To avoid damaging the audio system: the effective range of FM is about 25 miles • Be careful not to spill beverages over (40 km). Once outside this range, you may the audio system.
Page 255 1. AUDIO SYSTEM OPERATION ® COMPATIBLE MODELS Cargo loaded on the roof luggage carrier, Software especially metal objects, may adversely Model Generation Version ® affect the reception of XM Satellite Radio. iPod 1.3.0 Alternation or modifications carried out 1.1.2 without appropriate authorization may invalidate the user’s right to operate the iPod classic 2.0.1...
Page 256 1. AUDIO SYSTEM OPERATION USB MEMORY USB memory that can be used for MP3 and WMA playback. Audio CDs • USB communication formats: USB 2.0 FS (12 Mbps) ® • File formats: FAT 16/32 (Windows • Correspondence class: Mass storage class Use only discs marked as shown above.
Page 257 1. AUDIO SYSTEM OPERATION Low quality discs Correct Wrong Handle discs carefully, especially when you are inserting them. Hold them on the Labeled discs edge and do not bend them. Avoid getting fingerprints on them, particularly on the shiny side. Dirt, scratches, warping, pin holes, or other disc damage could cause the CD player to skip or to repeat a section of a...
Page 258 1. AUDIO SYSTEM OPERATION SAMPLING FREQUENCY MP3/WMA FILES MP3 files: MP3 (MPEG Audio Layer 3) and WMA MPEG 1 AUDIO LAYER 3 32, 44.1, 48 (Windows Media Audio) are audio com- pression standards. The MP3/WMA player can play MP3 and MPEG2 AUDIO LAYER3 16, 22.05, 24 WMA files on CD-ROM, CD-R and CD-...
Page 259 1. AUDIO SYSTEM OPERATION MP3/WMA files in folders up to 8 levels CD-R AND CD-RW DISCS deep can be played. However, the start of playback may be delayed when using CD-R/CD-RW discs that have not been discs containing numerous levels of fold- subject to the “finalizing process”...
Page 260 1. AUDIO SYSTEM OPERATION TERMS Playlists created using “WINAMP” soft- ware have a playlist file extension (.m3u). PACKET WRITE This is a general term that describes the process of writing data on-demand to CD- R, etc., in the same way that data is writ- MP3 is an audio compression standard ten to floppy or hard discs.
Page 261 1. AUDIO SYSTEM OPERATION ® Gracenote You agree that you will use Gracenote Data, the Gracenote Software, and Gracenote Servers for your own per- Music recognition technology sonal non-commercial use only. You related data provided ® agree not to assign, copy, transfer or Gracenote .
Page 262 1. AUDIO SYSTEM OPERATION The Gracenote Software and each item of Gracenote Data are licensed to you “AS IS.” Gracenote makes no rep- resentations or warranties, express or implied, regarding the accuracy of any Gracenote Data from in the Gracenote Servers.
Page 263 1. BASIC INFORMATION BEFORE OPERATION 1. QUICK REFERENCE Pressing the button allows access to the “Phone” menu screen. When the button is pressed, the screen that was last displayed is returned to. Touch to display the “Phone” menu screen. “Phone” menu screen The actual design and button position may differ depending on the vehicle.
Page 264 1. BASIC INFORMATION BEFORE OPERATION To display the “Dial By Number” screen, touch “Dial By Number” on the “Phone” menu screen, or touch on any of the “Phone” screens. The “Dial By Number” screen can also be displayed by pressing the switch on the steering wheel.
Page 265 1. BASIC INFORMATION BEFORE OPERATION Name Function The six bars display the charge level of the phone’s battery. The amount displayed does not always correspond with the The amount of amount displayed on the cellular phone. The amount of battery battery charge charge left may not be displayed depending on the phone.
Page 266 1. BASIC INFORMATION BEFORE OPERATION 2. HANDS-FREE SYSTEM ® Bluetooth hands-free system allows INFORMATION you to make or receive a call without ● If your cellular phone does not support ® taking your hands off the steering Bluetooth , this system will not function. wheel by connecting your cellular Depending on the cellular phone mod- ●...
Page 267 1. BASIC INFORMATION BEFORE OPERATION USING THE PHONE SWITCH The actual design and switch position may differ depending on the vehicle. Bluetooth is a registered trademark of For details, see the Pictorial index of Bluetooth SIG, Inc. “Owner’s Manual”. INFORMATION ●...
Page 268 1. BASIC INFORMATION BEFORE OPERATION ABOUT THE PHONE BOOK IN INFORMATION THIS SYSTEM ● The other party’s voice outputs from the front speaker. When the received calls or received voice outputs, the audio The following data is stored for every reg- from the audio system will be muted.
Page 269 1. BASIC INFORMATION BEFORE OPERATION CAUTION ● FCC WARNING: Changes or modifica- tions not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ● CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radi- ation exposure limits set forth for uncon- trolled equipment and meets the FCC radio frequency (RF) Exposure Guide-...
Page 270 1. BASIC INFORMATION BEFORE OPERATION ® 3. CONNECTING A Bluetooth PHONE ® Touch “Search Bluetooth devices”. CONNECTING A Bluetooth PHONE In order to use the hands-free system, it is necessary to pair the phone and connect the phone’s profile (HFP) with the system.
Page 271 1. BASIC INFORMATION BEFORE OPERATION Touch the device to be paired. The system waits for connection re- quests coming from the paired device. All requested profiles are connected automatically. If the automatic connection failed, the fol- lowing screen will be displayed. Touch “Connect for Phone”.
Page 272 1. BASIC INFORMATION BEFORE OPERATION ■ CONNECTING FROM THE DEVICE The following screen will be displayed. Press the button. To cancel this function, touch “Cancel”. Confirm the PIN. If the device supports SSP (Secure Sim- ple Pairing) Touch “Search Bluetooth devices”. Confirm the PIN displayed on the screen, and then touch “Accept”.
Page 273 1. BASIC INFORMATION BEFORE OPERATION RECONNECTING THE ® Bluetooth PHONE ® If a Bluetooth phone is disconnected due to poor reception from the ® Bluetooth network when the engine switch is in the “ACC” or “ON” position, system will automatically ®...
Page 274 1. BASIC INFORMATION BEFORE OPERATION 4. REGISTERING A ENTRY Select one of 4 phone types (“Mo- REGISTERING A NEW ENTRY bile”, “Home”, “Work” or “Other”) and input a number. Up to 200 numbers can be registered with this system. INFORMATION This function cannot be operated while ●...
Page 275 1. BASIC INFORMATION BEFORE OPERATION REGISTERING FROM THE “Dial INFORMATION By Number” SCREEN ● phone type registered “Mobile”. Touch “Dial By Number” on the If the contact includes an address and a ● “Phone” menu screen. phone number, they will be stored in the “Stored”...
Page 276 1. BASIC INFORMATION BEFORE OPERATION Touch the desired list to select the en- REGISTERING A ENTRY AS try. “Speed Dials” Phone numbers from the list in the “Stored” screen and “Phone Book” can be registered as speed dials. Up to 15 speed dials can be registered.
Page 277 1. BASIC INFORMATION BEFORE OPERATION DISPLAYING AND EDITING Function THE ENTRY INFORMATION Touch to display the details of the entry information. Detailed information of entries in the Touch the desired entry to call list can be displayed or edited. Touch to change the entry name. (See page 168.) Touch next to the desired entry...
Page 278 1. BASIC INFORMATION BEFORE OPERATION EDITING PHONE NUMBERS Touch “Edit Phone Numbers” on the entry options screen. Select one of 4 phone types and input a number. : Touch to delete one number. Touch and hold to continue deleting numbers. You can edit a number for each phone type.
Page 279 2. TELEPHONE OPERATION ® 1. CALLING ON A Bluetooth PHONE ® After a Bluetooth phone has been Touch connected, a call can be made using The connecting screen will be dis- the hands-free system. There are sev- played. eral methods by which a call can be made.
Page 280 2. TELEPHONE OPERATION Touch the desired entry. BY PHONE BOOK Calls can be made using the phone book data of the connected cellular phone. The phone book changes de- pending on the phone connected. If a contact does not have phone num- ber stored, the entry will be dimmed.
Page 281 2. TELEPHONE OPERATION Touch “Search Contact” to search by BY SPEED DIALS the contact’s name. This function cannot be operated while driving. You can call by “Speed Dial” number list. Registering number in the “Speed Touch to display and edit the entry Dial”...
Page 282 2. TELEPHONE OPERATION BY CALL HISTORY When is touched, the entry is reg- istered in the “Stored” list on the “Con- Calls can be made using one of the 4 tacts” screen. (See page 166.) call lists functions. Touch the desired entry. Touch “Call History”.
Page 283 2. TELEPHONE OPERATION BY POI CALL Calls can be made to a POI when its details are displayed on the screen. (See pages 32 and 36.) Touch The connecting screen will be dis- played. To cancel the call, touch “End Call”.
Page 284 2. TELEPHONE OPERATION ® 2. RECEIVING CALLS ON A Bluetooth PHONE Call waiting When a call is received, this screen is displayed and a sound is heard. The ongoing screen is displayed. (See page 176.) Press the switch on the steering wheel.
Page 285 2. TELEPHONE OPERATION ® 3. TALKING ON A Bluetooth PHONE ® Function While you are talking on a Bluetooth phone, the ongoing screen is dis- Touch to transfer the call. Touch played. The operations outlined below “Transfer to Phone” to change can be performed on this screen.
Page 286 2. TELEPHONE OPERATION ADJUSTING THE RECEIVER DIALING A SECOND NUMBER VOLUME Touch “Dial”. Touch Touch the desired method to call. If “Dial Number” is selected Touch “-” or “+” to adjust the volume of the other party’s voice. Input the number and then touch The receiver volume can also be If “Dial From Contacts”...
Page 287 2. TELEPHONE OPERATION If “Dial From Call History” is selected ■ CHANGING PARTIES Touch the desired list and then touch Touch “Swap Calls”. the desired entry. Every time “Swap Calls” is touched, the party who is on hold will be switched. ■...
Page 288 3. SHORT MESSAGE FUNCTION 1. SHORT MESSAGE FUNCTION Touch the desired short message. Received messages can be forwarded ® from the connected Bluetooth phone, enabling checking and replying using this system. RECEIVING A NEW SHORT MESSAGE When a new short message is re- The state of a message is shown by the following icons.
Page 289 3. SHORT MESSAGE FUNCTION The short message will be displayed. REPLYING THE SHORT MESSAGE Touch “Reply Free Text” or “Reply Template”. Input the short message. Touch “OK”. The short message will be sent. : Touch to have the short message read out.
Page 290 3. SHORT MESSAGE FUNCTION If “Select Contact” is selected Input the short message. (See page 182.) Touch the desired list. Touch “OK”. Touch the desired contact. Select the desired number/contact to The short message will be sent. whom the short message should be If a recipient is selected sent.
Page 291 3. SHORT MESSAGE FUNCTION Edit the short message. CREATE A NEW SHORT MESSAGE ■ FROM “Create Message” SCREEN Input the short message. This screen is not displayed while driving. When a template is touched, the screen will be changed to the recipient selection screen.
Page 292 3. SHORT MESSAGE FUNCTION REGISTER NEW TEMPLATES New templates can be created. Up to 15 templates can be registered. Touch “Prepare Template Message”. Input the short message. Touch “OK”. The message is registered in the tem- plate list on the “Use Template” screen.
Page 293 3. SHORT MESSAGE FUNCTION...
Page 294 1. VOICE COMMAND SYSTEM OPERATION 1. VOICE COMMAND SYSTEM The voice command system enables Talk switch the navigation, audio and hands-free Press the talk switch to start the voice systems to be operated using voice command system. commands. Press and hold the talk switch to cancel the voice command system.
Page 295 1. VOICE COMMAND SYSTEM OPERATION VOICE COMMAND SYSTEM INFORMATION OPERATION ● Wait for the confirmation beep before speaking a command. Voice commands may not be recognized ● Press the talk switch. • Spoken too quickly. The voice command system is acti- •...
Page 296 1. VOICE COMMAND SYSTEM OPERATION ■ DISPLAYING THE COMMAND LIST SCREEN Say “More commands” or touching “More commands” on the voice com- mand main menu screen. Say the desired command or touch the desired command. Say the desired command or touch the desired command.
Page 297 1. VEHICLE INFORMATION 1. QUICK REFERENCE Fuel consumption information and tire pressure value can be displayed. To access the vehicle information system, press the “CAR” button. The actual design and button position may differ depending on the vehicle. For details, see Section 3 of “Owner’s Manual”. The “Information”...
Page 298 1. VEHICLE INFORMATION 2. FUEL CONSUMPTION TRIP INFORMATION FUEL CONSUMPTION (VEHICLES WITH HYBRID SYSTEM) Fuel consumption such as shown be- low can be displayed on the screen. For details see Section 1-1 of “Owner’s Manual”. Energy monitor If the “Trip Information” screen is not dis- Trip consumption played, touch “Trip Information”.
Page 299 1. VEHICLE INFORMATION HISTORY If the “History” screen is not displayed, touch “History”. Name Previous fuel economy record Current fuel economy Best recorded fuel economy The average fuel consumption history is divided by color into past averages and the average fuel consumption since the last reset.
Page 300 1. VEHICLE INFORMATION 3. TIRE PRESSURE WARNING SYSTEM Touch “Tire Pressure”. Vehicles equipped with a tire pres- sure warning system will display a warning screen in addition to a warning indication on the meter if tire pressure becomes low. For in- formation on the tire pressure warning system, refer to “Owner’s Manual”.
Page 301 1. VEHICLE INFORMATION...
Page 302 1. SETUP OPERATION 1. QUICK REFERENCE To customize the function settings, press the “SETUP” button. The actual design and button position may differ depending on the vehicle. For details, see Section 3 of “Owner’s Manual”. Name Function Page Settings are available for language selection, “General”...
Page 303 1. SETUP OPERATION 2. GENERAL SETTINGS Settings are available for language se- SCREENS FOR GENERAL lection, operation sounds, etc. SETTINGS Press the “SETUP” button. Touch “General”. Touch the items to be set. On this screen, the following functions are operational. Function You can change the language.
Page 304 1. SETUP OPERATION SELECTING A LANGUAGE Function Touch to change a keyboard lay- The desired language can be selected. out. (See “SELECTING A KEY- BOARD LAYOUT” on page 199.) Press the “SETUP” button. Touch to set the navigation Touch “General” on the “Setup” prompt volume.
Page 305 1. SETUP OPERATION DELETE PERSONAL DATA SELECTING A KEYBOARD LAYOUT Press the “SETUP” button. Press the “SETUP” button. Touch “General” on the “Setup” Touch “General” on the “Setup” screen. screen Touch “Delete Personal Data”. Touch “Keyboard Layout”. Touch “Delete”. Touch the desired keyboard layout. INFORMATION “QWERTY”: Latin characters, “QWER- The following personal data can be...
Page 306 1. SETUP OPERATION 3. DISPLAY SETTINGS You can adjust the contrast and bright- TURN OFF DISPLAY ness of the screen. You can also turn the display off. Press the “SETUP” button. Press the “SETUP” button. Touch “Display” on the “Setup” screen.
Page 307 1. SETUP OPERATION CHANGING BETWEEN DAY ADJUST CONTRAST/ AND NIGHT MODE BRIGHTNESS Press the “SETUP” button. Depending on the position of the head- light switch, the screen changes to day Touch “Display” on the “Setup” or night mode. screen. To display the screen in day mode Touch “General”...
Page 308 1. SETUP OPERATION ® 4. Bluetooth SETTINGS ® ® Bluetooth FUNCTION ON/ To set up a Bluetooth device. Press the “SETUP” button. ® Bluetooth function switched on or off. Touch “Bluetooth ”. Touch “Bluetooth ”. Touch “On” or “Off”. INFORMATION ®...
Page 309 1. SETUP OPERATION ® Touch the device to be paired. PAIRING A Bluetooth DEVICE ® Up to 4 Bluetooth devices can be paired. A paired device can be con- nected to any of its supported profiles such as phone, music and/or internet. CONNECTING FROM THE ®...
Page 310 1. SETUP OPERATION The system waits for connection re- INFORMATION quests coming from the paired device. ● For details on device detection and the All requested profiles are connected ® operation of your Bluetooth device, see automatically. manual that comes with ®...
Page 311 1. SETUP OPERATION CONNECTING FROM THE LOGIN PROCESS INTERNET DEVICE PROFILE If “Connect for Internet” is selected Touch “Make Discoverable”. Touch “Connect for Internet”. ® When a Bluetooth device is currently connected, a pop-up window is displayed. To disconnect it, touch “Yes”. Touch the desired provider.
Page 312 1. SETUP OPERATION Touch “Confirm Provider Informa- DISPLAYING THE PAIRED tion”. DEVICE LIST Devices can be disconnected and each profile connection status can be changed using the list. Up to 4 devices can be paired at the same time. Touch “Paired Device List”. User login information can be changed on this screen.
Page 313 1. SETUP OPERATION CHANGING THE DEVICE NAME SETTING PIN Touch “Rename XX”. To change the PIN. Input the device name. Touch “Set PIN for Pairing”. Touch “OK”. DELETING A PAIRED DEVICE Touch “Delete Pairing”. Touch “Yes”. CONNECTING OR Input the desired number. DISCONNECTING PROFILES Touch the desired profile to be con- nected or disconnected.
Page 314 1. SETUP OPERATION SETTING THE INTERNET Function CONNECTION Touch to turn the automatic download of addresses function on or off. To change the internet settings. Touch to turn the show cost Touch “Internet Connection”. warning function on or off. When this function is activated, a pop-up window will be displayed before using Entune service.
Page 315 1. SETUP OPERATION 5. PHONE SETTINGS Settings are available for ringtone se- SCREEN FOR PHONE lection, announce incoming short mes- SETTINGS sage and email, and “Stored” lists. Press the “SETUP” button. On this screen, the following functions can be set. Function Touch “Phone”.
Page 316: Audio Settings
1. SETUP OPERATION 6. AUDIO SETTINGS Select the desired setting from “HD HD Radio™ system can be set using Radio/Analog Setting”. the following procedure: Press the “SETUP” button. Screen button Function Touch to receive both an- “All” alog and digital broad- casts.
Page 317 1. SETUP OPERATION 7. VEHICLE SETTINGS Vehicle customization settings can be changed. Press the “SETUP” button. Touch “Vehicle”. Touch the desired items to be set. For a list of the settings that can be changed, see “Owner’s Manual”. After changing the settings, touch “Save”.
Page 318 1. SETUP OPERATION...
Page 319 1. REAR VIEW MONITOR SYSTEM 1. REAR VIEW MONITOR SYSTEM OPERATION The rear view monitor system assists CAUTION the driver by displaying an image of the view behind the vehicle while backing ● Never depend on the rear view monitor system entirely when...
Page 320 Guide lines are displayed on the may change. Be sure to have the cam- screen. era’s position and mounting angle checked at your Toyota dealer. ● As the camera has a water proof con- struction, do not detach, disassemble or modify it.
Page 321 1. REAR VIEW MONITOR SYSTEM AREA DISPLAYED ON SCREEN Image is displayed approximately level on screen. INFORMATION ● The area displayed on the screen may vary according to vehicle orientation or road conditions. THE REAR VIEW MONITOR SYSTEM CAMERA The rear view monitor system camera is located as shown in the illustration.
Page 322 1. REAR VIEW MONITOR SYSTEM On some models INFORMATION ● The camera uses a special lens. The distance of the image that appears on the screen differs from the actual dis- tance. ● In the following cases, it may become difficult to see the images on the screen, even when the system is functioning.
Page 323 1. REAR VIEW MONITOR SYSTEM 2. DRIVING PRECAUTIONS (WITH REAR VIEW MONITOR GUIDE LINES) In any of the following situations, there is a margin of error between the guide lines on the screen and the actual dis- tance/course on the road. When the grade behind the vehicle slopes down sharply, objects appear to be closer than they actually are.
Page 324 1. REAR VIEW MONITOR SYSTEM Approx. 1.5 ft. (0.5 m) The distance that appears on the screen between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as fol- lows. • In reality, <...
Page 325 1. REAR VIEW MONITOR SYSTEM...
Page 326 TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior and Air conditioning and audio systems, as well as other in- exterior features terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 327 TABLE OF CONTENTS Index 1-6. Theft deterrent system Before driving Engine immobilizer system ... 84 1-7. Safety information 1-1. Key information Correct driving posture ..87 Keys ........34 SRS airbags ......89 Front passenger occupant 1-2. Opening, closing and locking classification system..
Page 328 2-4. Using other driving systems Interior and exterior Cruise control...... 174 features Rear view monitor system (vehicles with auto 3-1. Using the air conditioning anti-glare inside rear system and defogger view mirror) ....... 178 Air conditioning system ..248 Four-wheel drive system..186 Active traction control 3-2.
Page 329 TABLE OF CONTENTS Index 3-4. Using the hands-free phone 3-7. Other interior features system (for cellular phone) Sun visors......373 Hands-free phone system Vanity mirrors ..... 374 features ......326 Clock........375 Using the hands-free Outside temperature phone system....330 display (vehicles with Making a phone call ...
Page 330 4-3. Do-it-yourself maintenance 5-2. Steps to take in an emergency Do-it-yourself service If a warning light turns on precautions ....... 430 or a warning buzzer sounds......505 Hood ........434 If you have a flat tire ... 515 Engine compartment... 436 If the engine will not start..
Page 331 TABLE OF CONTENTS Index For owners Reporting safety defects for U.S. owners ....590 Seat belt instructions for Canadian owners (in French)......591 SRS airbag instructions for Canadian owners (in French)......593 Camper information.... 604 Index Abbreviation list......612 Alphabetical index ....614 What to do if...
Page 333 Pic t oria l inde x Exterior Regular Cab models Windshield wipers P. 168 Hood P. 434 Detachable pole Outside rear view mirrors P. 75 antenna P. 306 Front side marker lights P. 164 Headlights P. 164 Front turn signal lights/parking lights/ daytime running lights P.
Page 334 Rear turn signal lights P. 153 Fuel filler door P. 81 Stop/tail lights P. 164 Side doors P. 39 Tailgate P. 44 License plate lights P. 164 Tires ●Rotation P. 452 ●Replacement P. 515 Rear side marker lights P. 164 ●Inflation pressure P.
Page 335 Pic t oria l inde x Exterior Access Cab models Windshield wipers P. 168 Hood P. 434 Outside rear view mirrors Outside rear view mirrors P. 75 P. 75 Detachable pole antenna P. 306 Side turn signal lights P. 153 Front side marker lights P.
Page 336 Rear turn signal lights P. 153 Fuel filler door P. 81 Stop/tail lights P. 164 Access doors P. 43 Side doors P. 39 Tailgate P. 44 License plate lights P. 164 Tires ●Rotation P. 452 ●Replacement P. 515 Rear side marker lights P.
Page 337 Pic t oria l inde x Exterior Double Cab models Windshield wipers P. 168 Hood P. 434 Outside rear view mirrors P. 75 Detachable pole antenna P. 306 Side turn signal lights P. 153 Front side marker lights P. 164 Headlights P.
Page 338 Rear turn signal Fuel filler door P. 81 lights P. 153 Side doors P. 39 Stop/tail lights P. 164 Tailgate P. 44 License plate lights P. 164 Rear side marker lights P. 164 Tires ●Rotation P. 452 ●Replacement P. 515 ●Inflation pressure P.
Page 339 Pic t oria l inde x Interior Seat belts P. 63 Bottle holders P. 369 Front console box P. 366 Head restraints P. 58 Horn P. 156 SRS driver airbag P. 89 SRS front passenger airbag P. 89 Glove box P.
Page 340 P. 400 Compass P. 409 : Vehicles with auto anti-glare inside rear view mirror : If equipped : Access Cab and Double Cab models : For vehicles with a Display Audio system, refer to the “Display Audio System Owner’s Manual”.
Page 341 Pic t oria l inde x Interior Window lock switch P. 78 Inside door lock button P. 40 Power window switches P. 78 Door lock switch P. 40...
Page 342 Bench type front seat Shift lever P. 146, 150 Cup holders P. 367 Shift lock override button P. 533 Separated type front seats with an automatic transmission Shift lever P. 146 Cup holders P. 367 Cup holders P. 367 Shift lock override button P.
Page 343 Pic t oria l inde x Interior Separated type front seats with a manual transmission Shift lever P. 150 Cup holders P. 367...
Page 344 Access Cab models Sub woofer P. 300 Back window lock release lever P. 80 Auxiliary boxes P. 370 : If equipped...
Page 345 Pic t oria l inde x Interior Double Cab models Grocery bag hooks P. 398 Bottle holders Back window lock P. 369 release lever P. 80 Flashlight holder P. 397 Storage boxes P. 396 Cargo net hooks P. 399 : If equipped : Vehicles with sub woofer...
Page 346 Pic t oria l inde x Instrument panel Gauges and meters P. 157 Tilt and telescopic steering lock release lever P. 69 Tire pressure warning reset switch P. 453 Hood lock release lever P. 434 Parking brake pedal P. 154 Auxiliary box P.
Page 347 Pic t oria l inde x Instrument panel Audio system P. 255 Display Audio system Air conditioning system P. 248 Front-wheel drive Emergency flasher switch P. 496 control switch P. 186 A-TRAC switch P. 190 AUX port P. 301 USB port P.
Page 348 Cruise control switch P. 174 : 4WD models only : Refer to “Display Audio System Owner’s Manual”. : If equipped : For vehicles with a Display Audio system, refer : Vehicles with a manual transmission to “Display Audio System Owner’s Manual”.
Page 349 Pic t oria l inde x Instrument panel Fog light switch P. 167 RR DIFF LOCK switch P. 194 Instrument panel light control dial P. 158 Power outlet main switch P. 382 Headlight switch P. 164 Turn signal lever P. 153 RSCA OFF switch P.
Page 350 Pic t oria l inde x Luggage compartment Back window P. 80...
Page 351 Pic t oria l inde x Luggage compartment Tie-down cleats P. 394 Deck hooks P. 393 Deck rails P. 212 Deck hooks P. 393 Auxiliary boxes P. 392 Tie-down cleats P. 394 Deck rails P. 212 Deck hooks P. 393 Auxiliary boxes P.
Page 352 Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 353 ● Anti-lock brake system ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. Scrapping your Toyota The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals.
Page 354 The computers do not record conversations, sound or pictures. ● Data usage Toyota may use the data recorded in these computers to diagnose malfunc- tions, conduct research and development, and improve quality. Toyota will not disclose the recorded data to a third party except: •...
Page 355 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: •...
Page 356 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 357 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 358 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. ( P. 534)
Page 359 1-1. Key information NOTICE ■ To prevent key damage (vehicles with engine immobilizer system) ● Do not subject the keys to strong shocks, expose them to high tempera- tures by placing them in direct sunlight, or get them wet. ● Do not expose the keys to electromagnetic materials or attach any mate- rial that blocks electromagnetic waves to the key surface.
Page 360 1 -2 . Ope ning, c losing a nd loc k ing t he doors Wire le ss re m ot e c ont rol The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Locks all doors Unlocks all doors Pressing the button unlocks...
Page 361 Pressing a button may cause the wireless remote control to emit radio waves that could inter- fere with the operation of the aircraft. Customization that can be configured at Toyota dealer ■ Settings (e.g. wireless remote control system) can be changed.
Page 362 1-2. Opening, closing and locking the doors ■ Certification for wireless remote control MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ4-34R IC (Canada) IDs: Transmitter: 1470A-1T Receiver: 1470A-6R MADE IN U.S.A. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Page 363 1 -2 . Ope ning, c losing a nd loc k ing t he doors Side doors The vehicle can be locked/unlocked using the wireless remote con- trol, key or door lock switch. Wireless remote control (if equipped) ■ P. 36 ■...
Page 364 1-2. Opening, closing and locking the doors Door lock switch (if equipped) ■ Driver’s door lock switch Locks all doors Unlocks all doors Passenger’s door lock switch Locks all doors Unlocks all doors Inside door lock button ■ Locks the door Unlocks the door Pulling the inside handle can open the front door even if the...
Page 365 1-2. Opening, closing and locking the doors Locking the front doors from the outside without a key Move the inside door lock button to the lock position. Close the door. Vehicles with power door lock system The door cannot be locked if a front door is open and the key is in the engine switch.
Page 366 1-2. Opening, closing and locking the doors CAUTION ■ To prevent an accident Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●...
Page 367 1 -2 . Ope ning, c losing a nd loc k ing t he doors Ac c e ss doors (Ac c e ss Ca b m ode ls only) The access door (rear door) can be opened using the inside handle. Open the front door widely Pull (from the outside) or push (from the inside) the...
Page 368 1 -2 . Ope ning, c losing a nd loc k ing t he doors Ta ilgat e The tailgate can be opened. Pull the handle Open the tailgate slowly The support cables will hold the tailgate horizontal. After closing the tailgate, try pulling it toward you to make sure it is securely locked.
Page 369 1-2. Opening, closing and locking the doors To disconnect the wire harness connectors ( ), press and hold the lock of the tailgate wire harness connector (White) and pull apart. Tailgate wire harness connec- tor (White) Frame wire harness connector (Gray) Attach connector...
Page 370 1-2. Opening, closing and locking the doors Pull out the wire harness from the vehicle bed. Attach connector cover (Gray) to the tailgate wire har- ness connector (White). Tailgate wire harness connec- tor (White) Connector cover (Gray) ■ Removing the tailgate Open the tailgate to the angle where you can release the brackets on the support cables...
Page 371 1-2. Opening, closing and locking the doors Slide the tailgate a little to the right to unhook the left side. To attach the tailgate, follow the removal procedure in reverse order. Rear step bumper For rear end protection and eas- ier step-up loading.
Page 372 1-2. Opening, closing and locking the doors NOTICE ■ To prevent damage to the tailgate wire harness (vehicles with rear view monitor system) Do not pull out all of the tailgate wire harness before open the tailgate. ■ To prevent damage to the camera lens (vehicles with rear view monitor system) Store the removed tailgate with the back-up camera lens facing upward.
Page 373 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) Front se at s Bench type seat Seat position adjustment lever Separated type seats Seat position adjustment lever Driver’s seat lumbar sup- port adjustment knob...
Page 374 1-3. Adjustable components (seats, mirrors, steering wheel) Moving passenger’s seat for rear seat entry (if equipped) Lift the seatback angle adjusting lever or press the pedal behind the seatback. The seat will slide forward. Move the seat to the front-most position.
Page 375 1-3. Adjustable components (seats, mirrors, steering wheel) Folding passenger’s seat (vehicles with seatback table) Pull the seatback angle adjusting lever and raise the seatback to its upright position. Pull the seatback folding lever and fold the seatback down.
Page 376 1-3. Adjustable components (seats, mirrors, steering wheel) Active head restraints (Access Cab and Double Cab models only) When occupant’s back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward to help reduce the risk of whiplash on the seat occupant.
Page 377 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment ● Be careful that the seat does not hit passengers or luggage. Do not recline the seat more than necessary when the vehicle is in motion ● to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 378 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) Re a r se at s (Ac c e ss Ca b a nd Double Ca b m ode ls) Access Cab models The bottom cushion of the rear seats can be raised and lowered.
Page 379 1-3. Adjustable components (seats, mirrors, steering wheel) Double Cab models The seatback of the rear seat can be folded. ■ Before folding rear seats Stow the rear seat belt buck- les. This prevents the seat belt buckles from falling out when you fold the seatback.
Page 380 1-3. Adjustable components (seats, mirrors, steering wheel) Attach the head restraints to the holders located on the back sides of the bottom cush- ions. Fold down the seatback by pulling the lock release strap. ■ Waterproof and water-repellent seats (if equipped) Waterproof and water-repellent seats are installed in your vehicle;...
Page 381 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When the seatback is folded/the bottom cushion is raised Do not sit on or place anything on the seatback or auxiliary box while driving. When returning the seats to their original position ■...
Page 382 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) H e a d re st ra int s Head restraints are provided for all seats. ■...
Page 383 1-3. Adjustable components (seats, mirrors, steering wheel) When using the rear head restraints ■ Access Cab models To use Lift up the head restraint until it locks. To fold Pull the head restraint lock release lever to fold the head restraint.
Page 384 1-3. Adjustable components (seats, mirrors, steering wheel) Separated type seat Pull the head restraint up while pushing the lock release button. ■ Removing the rear head restraints (Double Cab models only) Pull the head restraint up while pushing the lock release button. Installing the front head restraints ■...
Page 385 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Installing the rear head restraints (Double Cab models only) Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
Page 386 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Head restraint precautions Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ● Use the head restraints designed for each respective seat. ●...
Page 387 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) Se at be lt s Make sure that all occupants are wearing their seat belts before driv- ing the vehicle.
Page 388 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the belt (front seats) ■ Move the height adjuster up as needed until you hear a click. Down Push the lock release button and slide the height adjuster down. ■...
Page 389 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 390 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. Toyota recommends that children be seated in the rear seat and always ● use a seat belt and/or an appropriate child restraint system.
Page 391 ● Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been...
Page 392 ● Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.
Page 393 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) St e e ring w he e l The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and press the lever down.
Page 394 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) Ant i-gla re inside re a r vie w m irror Glare from the headlights of vehicles behind can be reduced by using the following functions.
Page 395 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror (type A) In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode on/off The indicator comes on when automatic mode is turned on.
Page 396 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror (type B) In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode on/off The indicator comes on when automatic mode is turned on.
Page 397 1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror display (vehicles with auto anti-glare inside rear view mirror) The inside rear view mirror displays the following information. Also, the display and display settings can be changed. Compass ■ P.
Page 398 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Caution while driving Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
Page 399 1 -3 . Adjust a ble c om pone nt s (se a t s, m irrors, st e e ring w he e l) Out side re a r vie w m irrors Mirror angle can be adjusted. Power-adjustable type Select a mirror to adjust.
Page 400 1-3. Adjustable components (seats, mirrors, steering wheel) Manually adjustable type Adjust the mirror up, down, in or out by pushing the mirror surface. Folding back the mirrors Push backward to fold the mir- rors. ■ Mirror operating conditions (vehicles with power-adjustable type only) The engine switch is in the ACC or ON position.
Page 401 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When driving the vehicle Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●...
Page 402 1 -4 . Ope ning a nd c losing t he w indow s Pow e r w indow s The power windows can be opened/closed using the following switches. Driver’s power window switches Closing Opening One-touch opening (driver’s window only) *: Pressing the switch in the opposite direction will stop win- dow travel partway.
Page 403 1-4. Opening and closing the windows ■ The power windows can be operated when The engine switch is in the ON position. ■ Operating the power windows after turning the engine off The power windows can be operated for approximately 43 seconds even after the engine switch is turned to the ACC or LOCK position.
Page 404 1 -4 . Ope ning a nd c losing t he w indow s Ba ck w indow (ve hicle s w it h sliding t ype ) The back window can be opened and closed using the lock release lever.
Page 405 1 -5 . Re fue ling Ope ning t he fue l t a nk c a p Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Turn the engine switch off and ensure that all the doors and win- dows are closed.
Page 406 1-5. Refueling Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. ■ Fuel types Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] or higher) Fuel tank capacity ■...
Page 407 ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 408 1 -6 . T he ft de t e rre nt syst e m Engine im m obilize r syst e m The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer.
Page 409 1-6. Theft deterrent system ■ Certifications for the engine immobilizer system For vehicles sold in U.S.A. FCC ID: MOZRI-21BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 410 1-6. Theft deterrent system For vehicles sold in New Caledonia “Hereby, Tokai Rika Co., Ltd., declares that this Immobilizer, model RI-21BTY, is in compliance with the essential require- ments and other relevant provisions of Directive 1999/5/EC.” NOTICE ■ To ensure the system operates correctly Do not modify or remove the system.
Page 411 1 -7 . Sa fe t y inform a t ion Corre c t driving post ure Drive in a good posture as follows: Sit upright and well back in the seat. ( P. 49) Adjust the position of the seat forward or backward to ensure the pedals can be reached...
Page 412 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat while driving. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 413 1 -7 . Sa fe t y inform a t ion SRS a irba gs The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.
Page 414 1-7. Safety information Airbag system components Vehicles with bench type front seat Vehicles with separated type front seat...
Page 415 1-7. Safety information Front passenger airbag Driver’s seat position sen- Curtain shield airbags Driver’s seat belt buckle Side airbags switch AIR BAG ON and AIR BAG Front passenger’s seat belt OFF indicator lights buckle switch warning light Occupant detection system RSCA OFF indicator light (ECU and sensors) Driver airbag...
Page 416 1-7. Safety information In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. A chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants. ■...
Page 417 1-7. Safety information ● It is possible that in some collisions where the forward deceleration of the vehicle is very close to the designed threshold level, the SRS front air- bags and the seat belt pretensioners may not activate together. ●...
Page 418 1-7. Safety information The SRS curtain shield airbags may also deploy under the situation shown in the illustration. The angle of vehicle tip-up is marginal. ● ● The vehicle skids and hits a curb stone. Types of collisions that may not deploy the SRS airbag (front airbags) ■...
Page 419 1-7. Safety information ■ Types of collisions that may not deploy the SRS airbag (side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
Page 420 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. The front of the vehicle is damaged or ●...
Page 421 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
Page 422 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
Page 423 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 424 Wash off any residue as soon as possible to prevent skin irritation. ● If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.
Page 425 Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
Page 426 1-7. Safety information Deactivating the curtain shield airbags in a vehicle rollover (4WD models only) On/off (hold for a few seconds) The RSCA OFF indicator turns on (only when the engine switch is in the ON position.) The roll sensing function for the curtain shield airbags and seat belt pretensioners will turn back on automatically each time the...
Page 427 1 -7 . Sa fe t y inform a t ion Front pa sse nge r oc c upa nt cla ssific at ion syst e m Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the right front passenger seat and activates or deactivates the devices for the front passenger.
Page 428 1-7. Safety information Conditions and operation of the front passenger occupant classification system Adult* ■ AIR BAG ON and AIR BAG OFF indica- AIR BAG ON tor lights Indicator/ SRS warning light warning light Front passenger’s seat belt reminder Flashing* light Front passenger airbag Side airbag on the front passenger seat...
Page 429 1-7. Safety information ■ Unoccupied AIR BAG ON and AIR BAG OFF indica- Not illumi- tor lights nated Indicator/ SRS warning light warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Devices Activated Curtain shield airbag in the front passen-...
Page 430 1-7. Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. ( P. 108) : In case the indicator is not illuminated, consult this manual for installing the child restraint system properly.
Page 431 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 432 1 -7 . Sa fe t y inform a t ion Child re st ra int syst e m s A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt.
Page 433 1-7. Safety information Forward facing — Convertible seat Booster seat ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt. ●...
Page 434 ● Access Cab and Double Cab models: Toyota strongly urges the use of a proper child restraint system that conforms to the size of the child, installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 435 1-7. Safety information CAUTION ■ Child restraint precautions ● Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or an accident.
Page 436 1 -7 . Sa fe t y inform a t ion I nst a lling child re st ra int s Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt.
Page 437 1-7. Safety information Using the seat belts ■ Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) ( P. 63) ■ Using the top tether strap Regular Cab models with bench type seat Anchor bracket (for top tether strap) Anchor bracket is provided...
Page 438 1-7. Safety information Regular Cab models with separated type seat Anchor bracket (for top tether strap) Anchor bracket is provided for passenger seat. Access Cab models Anchor bracket (for top tether strap) Anchor bracket is provided for each rear seat.
Page 439 1-7. Safety information Double Cab models Anchor bracket (for top tether strap) Anchor bracket is provided for each rear seat.
Page 440 1-7. Safety information Installation with LATCH system (Access Cab models) Type A Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor.
Page 441 1-7. Safety information Type B Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a lower connector system.
Page 442 1-7. Safety information Installation with LATCH system (Double Cab models) Type A Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
Page 443 1-7. Safety information Type B Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a...
Page 444 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
Page 445 1-7. Safety information Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode.
Page 446 1-7. Safety information ■ Booster seat Place the booster seat on the seat facing the front of the vehi- cle. Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle.
Page 447 1-7. Safety information Child restraint systems with a top tether strap (Regular Cab models) ■ Bench type seat Remove the head restraint. Installing position: Right side passenger seat Center passenger seat Swing the seatback forward slightly ( P. 50) and remove the anchor bracket covers.
Page 448 1-7. Safety information Center passenger seat Route the top tether strap through the routing device as shown in the illustration. Make sure the top tether strap is not twisted. Latch the hook onto the anchor bracket. Return the seatback to its orig- inal position.
Page 449 1-7. Safety information ■ Separated type seat Remove the head restraint. Swing the seatback forward slightly ( P. 50) and remove the anchor bracket cover. Store the removed cover in a safe place such as the glove box. Route the top tether strap through the routing device as shown in the illustration.
Page 450 1-7. Safety information Replace the head restraint. Child restraint systems with a top tether strap (Access Cab models) Remove the anchor bracket cov- ers. Store the removed covers in a safe place such as the glove box. Secure the child restraint using a seat belt or lower anchors. Route the top tether strap through the routing device as shown in the illustration.
Page 451 1-7. Safety information Child restraint systems with a top tether strap (Double Cab models) Remove the head restraint. Installing position: Outside passenger seat Center passenger seat Outside passenger seat Swing the seatback forward slightly. ( P. 55) Latch the hook onto the anchor bracket.
Page 452 1-7. Safety information Secure the child restraint using a seat belt or lower anchors, and tighten the top tether strap. Make sure the top tether strap is securely latched. Replace the head restraint. Installing position: Outside passenger seat Center passenger seat ■...
Page 453 1-7. Safety information CAUTION ■ When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. ( P. 65) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
Page 454 1-7. Safety information CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
Page 455 2 -1 . Driving proc e dure s Driving t he ve hicle The following procedures should be observed to ensure safe driv- ing. Starting the engine ■ P. 143 ■ Driving Automatic transmission With the brake pedal depressed, shift the shift lever to D. ( P.
Page 456 2-1. Driving procedures Parking the vehicle ■ Automatic transmission With the shift lever in D, depress the brake pedal. Set the parking brake. ( P. 154) Shift the shift lever to P. ( P. 146) When parking on a hill, if necessary, block the wheels. Turn the engine switch to the LOCK position to stop the engine.
Page 457 Breaking in your new Toyota ■ To extend the life of the vehicle, the following precautions are recommended to observe: ●...
Page 458 Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. On vehicles with an automatic transmission, do not shift the shift lever to P ●...
Page 459 2-1. Driving procedures CAUTION ■ When driving the vehicle ● Do not shift the shift lever to R while the vehicle is moving forward. Doing so can damage the transmission and may result in a loss of vehicle control. ● Do not shift the shift lever to D (vehicles with an automatic transmission) or 1 (vehicles with a manual transmission) while the vehicle is moving back- ward.
Page 460 2-1. Driving procedures CAUTION ■ When driving the vehicle ● Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires.
Page 461 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● If the vehicle is stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed. ●...
Page 462 Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. Toyota does not recommend occupying the rear cargo area when it is fitted ● with a slide-in camper, camper shell or other type cover while the engine is running.
Page 463 2-1. Driving procedures CAUTION ■ When braking the vehicle ● Do not pump the brake pedal if the engine stalls. Each push on the brake pedal uses up the reserve for the power-assisted brakes. ● The brake system consists of 2 individual hydraulic systems: If one of the systems fails, the other will still operate.
Page 464 If you hear a squealing or scraping noise while driving (brake pad wear limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed.
Page 465 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ● Brake function ●...
Page 466 2 -1 . Driving proc e dure s Engine (ignit ion) sw it ch Engine switch ■ LOCK The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in P.) Some electrical components such as the audio system can...
Page 467 2-1. Driving procedures ■ Turning the key from ACC to LOCK Shift the shift lever to P (auto- matic transmission) or N (man- ual transmission). ( P. 146 150) Push in the key and turn to the LOCK position. Steering lock release ■...
Page 468 2-1. Driving procedures CAUTION ■ Caution while driving Do not turn the engine switch to the LOCK position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the ACC position. NOTICE ■...
Page 469 2 -1 . Driving proc e dure s Aut om at ic t ra nsm ission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever 5-speed models While the engine switch is on, depress the brake pedal and move the shift lever.
Page 470 2-1. Driving procedures 4-speed models While the engine switch is on, depress the brake pedal and move the shift lever. Shift position uses ■ Function Shift position 5-speed models 4-speed models Parking the vehicle or starting the engine Reversing Neutral Normal driving Position for engine brak- —...
Page 471 2-1. Driving procedures ■ Downshifting restrictions The shift lever cannot be downshifted if the following speeds are exceeded. 2WD models mph (km/h) Maximum speed Downshifting 5-speed models 4-speed models 81 (130) — 56 (90) 71 (115) 22 (35) 34 (55) 4WD models mph (km/h) Maximum speed...
Page 472 2-1. Driving procedures ■ When driving with the cruise control system (if equipped) The engine brake will not operate when downshifting from D to 4 (5-speed models) or 3 (4-speed models). ( P. 174) ■ If the shift lever cannot be shifted from P P.
Page 473 2 -1 . Driving proc e dure s M a nua l t ra nsm ission Shifting the shift lever ■ 6-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly. 5-speed models Fully depress the clutch pedal before operating the shift lever, and then release it slowly.
Page 474 2-1. Driving procedures ■ Maximum allowable speed Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. 2WD models except PreRunner mph (km/h) Maximum speed Shift position 6-speed models 5-speed models 32 (52) 33 (53) 61 (99) 63 (101) 91 (146)
Page 475 2-1. Driving procedures 4WD models mph (km/h) Maximum speed Shift position Transfer position 6-speed models 5-speed models H2 and H4 30 (49) 30 (48) 11 (19) 11 (18) H2 and H4 58 (93) 57 (92) 22 (36) 22 (36) H2 and H4 85 (137) 82 (133) 33 (53)
Page 476 2 -1 . Driving proc e dure s Tur n signa l leve r Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 477 2 -1 . Driving proc e dure s Pa rk ing bra ke Lever type ● Sets the parking brake Fully set the parking brake U.S.A. Canada while depressing the brake pedal. At this time, the indicator will come on. ●...
Page 478 2-1. Driving procedures ■ Parking brake engaged warning buzzer The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reach a speed of 3 mph [5 km/h]). Usage in winter time ■ See “Winter driving tips” for parking brake usage in winter time. ( P. 219) NOTICE ■...
Page 479 2 -1 . Driving proc e dure s H or n To sound the horn, press on or close to the mark. After adjusting the steering wheel ■ Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. ( P.
Page 480 2 -2 . Ga uge s a nd m e t e rs Ga uge s a nd m e t e rs The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute.
Page 481 2-2. Gauges and meters Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.
Page 482 2-2. Gauges and meters NOTICE ■ To prevent damage to the engine and its components ● Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. ● The engine may be overheating if the engine coolant temperature gauge is in the red zone (H).
Page 483 2 -2 . Ga uge s a nd m e t e rs I ndic at ors a nd w a r ning light s The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.
Page 484 2-2. Gauges and meters Indicators ■ The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Slip indicator ( P. 153) ( P. 190, 192, 201) Headlight high beam VSC OFF indicator indicator ( P. 165) ( P.
Page 485 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
Page 486 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 487 2 -3 . Ope ra t ing t he light s a nd w ipe rs H e a dlight sw it ch The headlights can be operated manually. Turning the end of the lever turns on the lights as follows: Type A Vehicles with day- time...
Page 488 2-3. Operating the lights and wipers Type B Vehicles with day- time running light system: The daytime running lights turn side marker, parking, tail, license plate, daytime run- Canada U.S.A. ning lights equipped) and instru- ment panel lights turn The headlights and all lights listed above (except daytime run- ning lights) turn on.
Page 489 2-3. Operating the lights and wipers ■ Daytime running light system (if equipped) To make your vehicle more visible to other drivers, the front turn signal ● lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night.
Page 490 2 -3 . Ope ra t ing t he light s a nd w ipe rs Fog light sw it ch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. On/off The fog lights can be turned on only when ■...
Page 491 2 -3 . Ope ra t ing t he light s a nd w ipe rs Windshie ld w ipe rs a nd w a she r Without intermittent type ■ Type A speed wind- shield wiper opera- tion High speed wind- shield wiper opera-...
Page 492 2-3. Operating the lights and wipers Type B speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation Washer operation...
Page 493 2-3. Operating the lights and wipers Intermittent wiper with interval adjuster ■ Wiper intervals can be adjusted for intermittent operation (when is selected). Type A Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 494 2-3. Operating the lights and wipers Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. Type B Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 495 2-3. Operating the lights and wipers Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency STY23AF020 Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. ■ The windshield wiper and washer can be operated when The engine switch must be in the ON position.
Page 496 2-3. Operating the lights and wipers NOTICE ■ When the windshield is dry Do not use the wipers, as they may damage the windshield. When there is no washer fluid spray from the nozzle ■ Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.
Page 497 2 -4 . U sing ot he r driving syst e m s Cruise c ont rol Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicator Cruise control switch Setting the vehicle speed ■ Press the ON-OFF button to activate the cruise control.
Page 498 2-4. Using other driving systems Adjusting the set speed ■ To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
Page 499 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
Page 500 2-4. Using other driving systems CAUTION ■ To avoid operating the cruise control by mistake Switch the cruise control off using the ON-OFF button when not in use. Situations unsuitable for cruise control ■ Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
Page 501 2 -4 . U sing ot he r driving syst e m s Rear view monitor system (vehicles with auto anti-glare inside rear view mirror) The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen.
Page 502 2-4. Using other driving systems ■ The rear view monitor system can be operated when The shift lever is in R and engine switch is ON. ■ Switching the screen on/off mode The rear view monitor display on the inside rear view mirror can be turned on/off.
Page 503 2-4. Using other driving systems ■ Displayed area The area covered by the camera is lim- ited. Objects that are close to either corner of the bumper or under the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.
Page 504 2-4. Using other driving systems ■ Driving precautions When the grade behind the vehicle slopes up sharply, objects appear to be farther away than they actually are. When the grade behind the vehicle slopes down sharply, objects appear to be closer than they actually are.
Page 505 2-4. Using other driving systems The distance that appears on the screen Approx. 1.5 ft. (0.5 m) between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as follows. In reality, C = A < B (C and A are equally far away;...
Page 506 2-4. Using other driving systems ■ Rear view monitor system camera The rear view monitor system camera is located on the tailgate as shown in the illustration. In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly.
Page 507 ■ ● If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer. ● Rapid temperature changes, such as when hot water is poured on the vehicle in cold weather, may cause the system to function abnormally.
Page 508 2-4. Using other driving systems NOTICE ■ Handling of the camera ● As the camera has a water proof construction, do not detach, disassemble or modify it. This may cause incorrect operation. ● If the camera lens becomes dirty, it cannot transmit a clear image. If water droplets, snow, or mud adhere to the lens, rinse with water and wipe with a soft cloth.
Page 509 2 -4 . U sing ot he r driving syst e m s Four-w he e l drive syst e m Use the front-wheel drive control switch to select the following transfer modes. H2 (high speed position, two-wheel drive) Use this for normal driving on dry hard-surfaced roads.
Page 510 2-4. Using other driving systems Shifting between H4 and L4 ■ Shifting from H4 to L4 Automatic transmission Stop the vehicle completely with brake pedal help down. Shift the shift lever to N. Push and turn the front-wheel drive control switch fully clock- wise.
Page 511 If the indicator light continues to blink even if doing so, contact your Toyota dealer as soon as possible. There may be a trouble in the four-wheel drive...
Page 512 2-4. Using other driving systems ■ Shifting to L4 VSC is automatically turned off. ■ Four-wheel drive usage frequency You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front-drive components are lubricated. CAUTION ■...
Page 513 2 -4 . U sing ot he r driving syst e m s Ac t ive t ra c t ion c ont rol syst e m The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces.
Page 514 2-4. Using other driving systems ■ When the rear differential is locked (vehicles with the rear differential lock system) The active traction control system is activated only when the vehicle speed is less than 3 mph (6 km/h). ■ Sounds and vibrations caused by the active traction control system ●...
Page 515 2 -4 . U sing ot he r driving syst e m s AU TO LSD syst e m The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin.
Page 516 2-4. Using other driving systems ■ If the engine is turned off and restarted The AUTO LSD system and the indicators are automatically turned off. ■ Reactivation of the VSC system linked to vehicle speed When the AUTO LSD system is turned on, the VSC system will turn on auto- matically if vehicle speed increases.
Page 517 2 -4 . U sing ot he r driving syst e m s Re a r diffe re nt ia l lock syst e m The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning.
Page 518 2-4. Using other driving systems Manual transmission 4WD models: Before using the rear differential lock system. Stop the vehicle or reduce your speed to less than 2 mph (3 km/h). Depress the clutch pedal and put the front-wheel drive control switch in the L4 position to see if this is sufficient. If this has no effect, additionally use the rear differential lock system.
Page 519 2-4. Using other driving systems ■ After unlocking the rear differential To check that the indicator goes off, turn the engine switch to the ON posi- tion, but do not start the engine. CAUTION ■ To avoid an accident ● Do not use the rear differential lock system except when wheel spinning occurs in a ditch or on a slippery or ragged surface.
Page 520 2 -4 . U sing ot he r driving syst e m s Dow nhill Assist Cont rol syst e m The downhill assist control system helps to prevent excessive speed on steep downhill descents. System operation ■ The system will operate when the vehicle is traveling under 15 mph (25 km/h) and the front-wheel drive control switch is in the L4 position.
Page 521 ● The downhill assist control system indicator does not come on when the DAC switch is pressed. In the above cases have your vehicle checked by your Toyota dealer. CAUTION Do not rely excessively on the downhill assist control system ■...
Page 522 2 -4 . U sing ot he r driving syst e m s Clut ch st a r t c a nc e l sw it ch The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged. Never use the switch for normal engine starting.
Page 523 2 -4 . U sing ot he r driving syst e m s Driving a ssist syst e m s To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle.
Page 524 2-4. Using other driving systems When the VSC/Trailer Sway Control/TRAC/hill-start assist control systems are operating If the vehicle is in danger of slip- ping or rolling backward when starting on an incline, or if any of the drive wheels spins, the slip indicator light flashes to indicate that the VSC/Trailer Sway Con- trol/TRAC/hill-start assist control...
Page 525 2-4. Using other driving systems To disable VSC, Trailer Sway Control and TRAC (2WD models and 2WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and TRAC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it.
Page 526 2-4. Using other driving systems To disable VSC, Trailer Sway Control and/or TRAC (4WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and TRAC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it.
Page 527 When the TRAC OFF indicator light comes on even if the VSC OFF switch has not been pressed TRAC, hill-start assist control, downhill assist control system cannot be oper- ated. Contact your Toyota dealer. ■ Reactivation of the TRAC, VSC and Trailer Sway Control systems after...
Page 528 2-4. Using other driving systems ■ Hill-start assist control will not operate when (if equipped) The shift lever is in the P, R or N positions. ● ● The rear differential is locked. ■ If the brake system overheats TRAC and hill-start control will cease operation and a buzzer will sound to alert the driver.
Page 529 The ABS, VSC, TRAC and Trailer Sway Control will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. Handling of tires and suspension ■...
Page 530 2 -5 . Driving inform a t ion Off-road precautions (4WD models and PreRunner) This vehicle has higher ground clearance and narrower tread in rela- tion to the height of its center of gravity to make it capable of per- forming in a wide variety of off-road applications.
Page 531 2-5. Driving information CAUTION ■ Off-road vehicle precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 532 2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
Page 533 2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to minimize the risk of serious injury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places. Do not grip the steering wheel spokes when driving off-road.
Page 534 2-5. Driving information NOTICE ■ To prevent the water damage ● Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ●...
Page 535 ● For better fuel economy, do not carry unnecessary weight. ■ Deck rails Headboard rail Side rails To use the deck rails, you must install genuine Toyota accessories or their equiva- lent for the deck rails. Follow manufacturer’s instructions and precautions...
Page 536 2-5. Driving information CAUTION When you secure cargo with the deck rails ■ Spread out tie-down/support locations evenly along the length of the ● rails. Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail. ●...
Page 537 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Example on your vehicle Cargo capacity Total load capacity...
Page 538 2-5. Driving information CAUTION Things that must not be carried in the luggage compartment ■ The following things may cause a fire if loaded in the luggage compart- ment. Receptacles containing gasoline ● Aerosol cans ● Storage precautions ■ Observe the following precautions. Failing to do so may result in death or serious injury.
Page 539 2-5. Driving information CAUTION Capacity and distribution ■ Do not exceed the maximum axle weight rating or the total vehicle ● weight rating. Even if the total load of occupant’s weight and the cargo load is less ● than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.
Page 540 2 -5 . Driving inform a t ion Ve hicle loa d lim it s Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. Total load capacity: ( P. 549) ■ Total load capacity means the combined weight of occupants, cargo and luggage.
Page 541 2-5. Driving information CAUTION Overloading the vehicle ■ Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
Page 542 2 -5 . Driving inform a t ion Wint e r driving t ips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■...
Page 543 2-5. Driving information When driving the vehicle ■ Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. When parking the vehicle ■ Park the vehicle and move the shift lever to P (automatic trans- mission) or 1 or R (manual transmission) without setting the parking brake.
Page 544 2-5. Driving information ■ Snow chain installation Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the rear tires only. Do not install tire chains on the front tires.
Page 545 NOTICE Repairing or replacing snow tires ■ Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 546 To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional...
Page 547 2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
Page 548 2-5. Driving information ■ GAWR (Gross Axle Weight Rating) The maximum allowable gross Front GAWR axle weight. The gross axle weight is the load placed on each axle (front and rear). Rear GAWR ■ TWR (Trailer Weight Rating) The maximum allowable gross (With brakes) trailer weight.
Page 549 2-5. Driving information ■ Unbraked TWR (Unbraked Trailer Weight Rating) The trailer weight rating for tow- (Without brakes) ing a trailer without a trailer ser- vice brake system. Tongue Weight ■ The load placed on the trailer hitch ball. ( P. 232)
Page 550 2-5. Driving information Weight limits ● The gross trailer weight must never exceed the TWR described in the table. ( P. 228, 551) ● The gross combination weight must never exceed the GCWR described in the table. ( P. 228) Regular Cab models and Double Cab models ●...
Page 551 2-5. Driving information GCWR, TWR, Unbraked TWR, Fifth wheel and Gooseneck towing TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR and TWR Regular Cab models Driving Model code...
Page 552 2-5. Driving information Access Cab models Driving Model code Engine GCWR system TRN225L- 7440 lb. CRMDKA (3370 kg) TRN225L- 7470 lb. (3385 kg) CRPDKA 2.7 L TRN245L- 4-cylinder 7850 lb. 3500 lb. CRMDKA (2TR-FE) (3560 kg) (1585 kg) engine TRN245L- 7870 lb.
Page 553 2-5. Driving information Double Cab models Driving Model code Engine GCWR system TRN225L- 7450 lb. 3400 lb. 2.7 L PRPDKA (3375 kg) (1540 kg) 4-cylinder (2TR-FE) TRN265L- 7710 lb. 3500 lb. engine PRPDKA (3495 kg) (1585 kg) 8040 lb. 3500 lb. (3645 kg) (1585 kg) GRN245L-...
Page 554 : With towing package ■ Unbraked TWR 1000 lb. (450 kg) Fifth wheel and gooseneck towing TWR ■ Toyota does not recommend fifth wheel and gooseneck towing. : These models meet the tow-vehicle trailering requirement of SAE International per SAE J2807.
Page 555 2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. •...
Page 556 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
Page 557 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
Page 558 2-5. Driving information Positions for towing hitch receiver and hitch ball Weight carrying ball position: 56.1 in. (1425 mm) Hitch receiver pin hole posi- tion: 44.2 in. (1123 mm) Connecting trailer lights Vehicles with 7 pin connector Use the wire harness stored in the rear end under the vehicle body.
Page 559 ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
Page 560 2-5. Driving information ● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right.
Page 561 2-5. Driving information ● Instability happens more frequently when descending steep or long downhill grades. Before descending, slow down and downshift. Do not make sudden downshifts while descending steep or long down- hill grades. ● Avoid holding the brake pedal down too long or applying the brakes too frequently.
Page 562 2-5. Driving information Release the parking brake (and also the brake pedal on vehi- cles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks. ■ Matching trailer ball height to trailer coupler height No matter which class of tow hitch applies, for a more safe trailer hookup,...
Page 563 Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
Page 564 2-5. Driving information ● After the trailer swaying has stopped: • Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer. Make sure the load has not shifted.
Page 565 2-5. Driving information CAUTION ■ To avoid accident or injury ● Do not exceed 65 mph (104 km/h), the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Slow down sufficiently before making a turn, in cross winds, on wet or slippery surface, etc.
Page 566 NOTICE When installing a trailer hitch ■ Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ■ Do not directly splice trailer lights Do not directly splice trailer lights.
Page 567 2 -5 . Driving inform a t ion Dinghy t ow ing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
Page 568 2-5. Driving information...
Page 569 3 -1 . U sing t he a ir c ondit ioning syst e m a nd de fogge r Air c ondit ioning syst e m Temperature control dial Air outlet selection dial Fan speed control dial Outside air or recirculated Air conditioning air mode switch ON/OFF switch...
Page 570 3-1. Using the air conditioning system and defogger ■ Selecting the air outlets Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment. When the dial is set to , air flows to the upper body.
Page 571 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the feet and the wind- shield defogger operates. The air intake selector is automat- ically set to outside air mode. To return the recirculated air mode, press Double Cab models only When the dial is set to...
Page 572 3-1. Using the air conditioning system and defogger ■ If the ambient temperature drops while using the recirculated air mode The air intake mode automatically changes from recirculated air mode to outside air mode after a few minutes. To cancel this function: Press and hold for longer than 2 seconds.
Page 573 3-1. Using the air conditioning system and defogger Right and left side outlets Direct air flow to the left or right, up or down. Opening and closing the air outlets Center outlets Open the vent. Close the vent.
Page 574 3-1. Using the air conditioning system and defogger Right and left side outlets Open the vent. Close the vent. For quick clearing of the windshield and side windows ■ Press to turn the air conditioning on. ■ Using the system in recirculated air mode The windows will fog up more easily if the recirculated air mode is used for an extended period.
Page 575 3-1. Using the air conditioning system and defogger CAUTION ■ To prevent the windshield from fogging up Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.
Page 576 3 -2 . U sing t he a udio syst e m Audio syst e m t ype s With Display Audio system Owners of models equipped with a Display Audio system should refer to the “Display Audio System Owner’s Manual”. Without Display Audio system...
Page 577 3-2. Using the audio system Type B: CD player with changer controller and AM/FM radio Title Page Using the radio P. 260 Using the CD player P. 267 Playing MP3 and WMA discs P. 273 Operating an iPod P. 280 Operating a USB memory P.
Page 578 3-2. Using the audio system Language settings Vehicles with Display Audio system Refer to “Display Audio System Owner’s Manual”. Vehicles without Display Audio system (type B only) The language used for all voice guidance, voice recognition and mes- sages may be changed. Press Press (MORE).
Page 579 3-2. Using the audio system ® ■ About Bluetooth (vehicles with Display Audio system) Bluetooth is a registered trademark of Bluetooth SIG. Inc. The Bluetooth wordmark and logo are owned by Bluetooth SIG. and permission has been granted to use the trademark of...
Page 580 3-2. Using the audio system CAUTION Vehicles with Display Audio system Properly shielded a grounded cables and connectors must be used for connection to host computer and/or peripherals in order to meet FCC emission limits. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Page 581 3 -2 . U sing t he a udio syst e m U sing t he ra dio Type A Power Volume Adjusting the Station selector frequency (AM, FM mode) or channel (SAT mode) Seeking Changing the frequency the channel Scanning for AM SAT/FM Displaying radio...
Page 582 3-2. Using the audio system ® Setting station presets (excluding XM Satellite Radio) Search for desired stations by turning pressing “ ” or “ ” on Press and hold a button (from ) until you hear a beep. Type B only: Each time is pressed, station pages are changed.
Page 583 3-2. Using the audio system ■ Displaying radio text messages (FM mode only) When a new radio text message is received, “MSG” is shown on the display. To display the message, press If the text continues past the end of the display, “ ”...
Page 584 3-2. Using the audio system ® ■ Scanning XM Satellite Radio channels ● Scanning channels in the current category Press When the desired channel is reached, press again. ● Scanning the preset channels Press and hold until you hear a beep. When the desired channel is reached, press again.
Page 585 3-2. Using the audio system ■ Reception sensitivity Type B only: Cargo loaded on the roof luggage carrier, especially metal ● ® objects, may adversely affect the reception of XM Satellite Radio. Maintaining perfect radio reception at all times is difficult due to the con- ●...
Page 586 CHECK ANTENNA There is a short-circuit in the antenna or the sur- rounding antenna cable. See a Toyota certified dealer. ® You have not subscribed to XM Satellite Radio. The radio is being updated with the latest encryp- ®...
Page 587 3-2. Using the audio system The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. ® Contact the XM Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 209-0079 (Canada) ■...
Page 588 3 -2 . U sing t he a udio syst e m U sing t he CD pla ye r Type A Power Volume Selector buttons CD eject Selecting a track Fast-forwarding and reversing/ Displaying text Selecting a track Searching messages Playback playback...
Page 589 3-2. Using the audio system Loading CD Insert a CD. Ejecting CD Press and remove the CD. Selecting a track Turn or press “ ” or “ ” on to select the desired track. Fast-forwarding and reversing tracks Press and hold “ ” or “ ” on Scanning tracks Press The first 10 seconds of each track will be played.
Page 590 3-2. Using the audio system Random playback Type A: Press (RAND). Songs are played in random order. To cancel, press the button again. Type B: Press (RDM). Songs are played in random order. To cancel, press the button again. Repeat play Type A: Press (RPT).
Page 591 The CD may be dirty, damaged or inserted up-side down. “PLEASE WAIT”: Operation has stopped due to a high temperature inside the player. Wait for a while and then press Contact your Toyota dealer if the CD still cannot be played back. ■ Discs that can be used Discs with the marks shown below can be used.
Page 592 3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or Dual Discs. Doing so may damage the CD player and/or the CD insert/eject function. ●...
Page 593 3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ●...
Page 594 3 -2 . U sing t he a udio syst e m Pla ying M P3 a nd WM A disc s Type A Power Volume Selector buttons CD eject Selecting a file Fast-forwarding Selecting a folder and reversing/ Selecting a file Displaying text Searching Playback...
Page 595 3-2. Using the audio system Loading and ejecting MP3 and WMA discs P. 268 Selecting and scanning a folder Selecting folders one at a time ■ Press “ ” or “ ” on to select the desired folder. ■ Scanning the first file of all the folders Press and hold until you hear a beep.
Page 596 3-2. Using the audio system Playing and pausing files (type B only) Press Random playback Type A: Press (RAND). To cancel, press the button again. Type B: Press (RDM). To cancel, press the button again. Repeat play ■ Repeating a file Type A: Press (RPT).
Page 597 “PLEASE WAIT”: Operation has stopped due to a high temperature inside the player. Wait for a while and then press . Con- tact your Toyota dealer if the CD still cannot be played. Discs that can be used ■ P. 270 ■...
Page 598 3-2. Using the audio system ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. ® WMA (Windows Media Audio) is a Microsoft audio compression format.
Page 599 3-2. Using the audio system ● Compatible disc formats The following disc formats can be used. • Disc formats: CD-ROM Mode 1 and Mode 2 CD-ROM XA Mode 2, Form 1 and Form 2 • File formats: ISO9660 Level 1, Level 2, (Romeo, Joliet) MP3 and WMA files written in any format other than those listed above may not play correctly, and their file names and folder names may not be displayed correctly.
Page 600 3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers.
Page 601 3 -2 . U sing t he a udio syst e m Ope rat ing a n iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. Connecting an iPod ■ Open the cover and connect an iPod using an iPod cable. Turn on the power of the iPod if it is not turned on.
Page 602: Control Panel
3-2. Using the audio system Control panel ■ Power Volume Selector buttons Selector knob Fast-forwarding and reversing/ Selecting a song Playback Displaying text Playback/ messages pause...
Page 603 3-2. Using the audio system Selecting a play mode Press (BROWSE) to select iPod menu mode. Press as that corresponds to the desired play mode. Press (MORE) to change to the second selection list. Play mode list ■ First Second Third Fourth Play mode...
Page 604 3-2. Using the audio system ■ Selecting a list Turn to display the first selection list. Press to select the desired item. Pressing that corresponds to “MORE” changes to the second selection list. Repeat the same procedure to select the desired song name. To return to the previous selection list, press Selecting songs from a song list Press...
Page 605 3-2. Using the audio system Playing and pausing songs Press Fast-forwarding and reversing songs Press and hold “ ” or “ ” on Shuffle playback ■ Playing songs from one playlist or album in random order Press (RDM). To cancel, press the button twice. ■...
Page 606 3-2. Using the audio system ■ About iPod Apple is not responsible for the operation of this device or its compliance ● with safety and regulatory standards. iPod is a trademark of Apple Inc., registered in the U.S. and other coun- ●...
Page 607 3-2. Using the audio system ■ Compatible models Model Generation Software version iPod 5th generation Ver. 1.2.0 or higher iPod nano 1st generation Ver. 1.3.0 or higher 2nd generation Ver. 1.1.2 or higher 3rd generation Ver. 1.0.0 or higher iPod touch 1st generation Ver.
Page 608 3-2. Using the audio system NOTICE ■ To prevent damage to iPod ● Do not leave iPod in the vehicle. The temperature inside the vehicle may become high, resulting in damage to the player. ● Do not push down on or apply unnecessary pressure to the iPod while it is connected as this may damage the iPod or its terminal.
Page 609 3 -2 . U sing t he a udio syst e m Ope rat ing a U SB m e m or y Connecting a USB memory enables you to enjoy music from the vehicle speakers. Connecting a USB memory ■...
Page 610 3-2. Using the audio system Control panel ■ Power Volume Selector buttons Selecting a file Fast-forwarding Selecting a folder and reversing/ Playback Selecting a file Searching Displaying text Playback/ playback messages pause Selecting and scanning a folder ■ Selecting a folder Press “...
Page 611 3-2. Using the audio system Selecting and scanning files ■ Selecting a file Turn or press “ ” or “ ” on to select the desired file. ■ Scanning the files in a folder Press The first 10 seconds of each file will be played. To cancel, press again.
Page 612 3-2. Using the audio system Repeat play ■ Repeating a file Press (RPT). To cancel, press the button twice. ■ Repeating all the files in a folder Press (RPT) twice. To cancel, press the button again. Switching the display Press Each time is pressed, the display changes in the following order: Track title...
Page 613 3-2. Using the audio system ■ USB memory Compatible device ● USB memory that can be used for MP3 and WMA playback. Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: •...
Page 614 3-2. Using the audio system ● MP3 file compatibility • Compatible standards MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, III, MPEG2.5) • Compatible sampling frequencies MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz) MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz) MPEG2.5: 8, 11.025, 12 (kHz) •...
Page 615 3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers.
Page 616 3 -2 . U sing t he a udio syst e m Opt im a l use of t he a udio syst e m Type A Adjusting the sound quality and ASL Type B Selector buttons Selector knob Menu button...
Page 617 3-2. Using the audio system Using the audio control function ■ Changing sound quality modes Type A: Pressing selects the mode to be changed in the following order: “BAS” “TRE” “FAD” “BAL” “ASL” Type B: Press Press as corresponds to the desired mode. “BASS”, “TREB”, “FADE”, or “BAL”...
Page 618 3-2. Using the audio system ■ Adjusting sound quality Type A: Turning adjusts the level. Mode Sound qual- Turn to the Turn to the Level displayed ity mode left right Bass* -5 to 5 High Treble* -5 to 5 Front/rear Shifts to volume F7 to R7...
Page 619 3-2. Using the audio system Type B: Turning adjusts the level. Mode Sound qual- Turn to the Turn to the Level displayed ity mode left right BASS Bass* -5 to 5 High TREB Treble* -5 to 5 Front/rear Shifts to FADE volume F7 to R7...
Page 620 3-2. Using the audio system Type B: Press Press (MORE). Press (ASL). Press as corresponds to the desired mode (OFF, LOW, MID, or HIGH). ASL automatically adjusts the volume and tone quality according to vehicle speed. ■ Setting the number of preset pages (type B only) The number of preset pages desired can be set from 1 to 6.
Page 621 3 -2 . U sing t he a udio syst e m Operating the sub w oofer (on some Access Cab models) LIGHT ON The sub woofer illumination turns on. In this position, the sub woofer operates.
Page 622 3 -2 . U sing t he a udio syst e m U sing t he AU X por t This adapter can be used to connect a portable audio device and lis- ten to it through the vehicle’s speakers. Open the cover and connect the portable audio device.
Page 623 3-2. Using the audio system Type B Press ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle’s audio controls. All other adjustments must be made on the portable audio device itself. ■...
Page 624 3 -2 . U sing t he a udio syst e m U sing t he st e e ring w he e l a udio sw it che s Some audio features can be controlled using the switches on the steering wheel.
Page 625 3-2. Using the audio system Turning the power on Press when the audio system is turned off. The audio system can be turned off by holding the switch down until you hear a beep. Changing the audio source Press when the audio system is turned on. The audio source changes as follows each time the switch is pressed.
Page 626 3-2. Using the audio system Selecting a track/file or song Press to select the CD, iPod, USB memory or Blue- ® tooth audio mode. Press “ ” or “ ” on to select the desired track/file or song. Selecting a folder or album ®...
Page 627 3 -2 . U sing t he a udio syst e m De t a cha ble pole a nt e nna The antenna can be removed. ■ Removing the antenna Place the included wrench around the antenna. When not in use, the wrench is stored in glove box.
Page 628 3-2. Using the audio system Installing the antenna ■ Tighten the antenna by one hand until it will not turn any more. Using the wrench, tighten the antenna an additional 1/8th turn (20 to 45 degrees) to secure it in place. After tightening the antenna, remove the wrench.
Page 629 3-2. Using the audio system NOTICE ■ To avoid damaging the antenna Remove the antenna in the following situations. When using an automatic carwash. ● ● When the antenna will touch the ceiling of a garage, etc. ● When covering the vehicle with a car cover. ■...
Page 630 ® 3 -3 . U sing t he Blue t oot h a udio syst e m ® Blue t oot h a udio syst e m ® The Bluetooth audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication.
Page 631 ® 3-3. Using the Bluetooth audio system ® ■ About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG. Inc. ■ Compatible models ® Bluetooth specifications: ● Ver. 1.2 Following Profiles: ● • A2DP (Advanced Audio Distribution Profile) Ver. 1.0 •...
Page 632 ® 3-3. Using the Bluetooth audio system CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio frequency exposure. This device is approved for Mobile Application only and, to comply with applicable FCC radio frequency exposure regula- tions, must be used with a distance of at least 7.9 in.
Page 633 ® 3 -3 . U sing t he Blue t oot h a udio syst e m ® U sing t he Blue t oot h a udio syst e m Audio unit ■ Display A message, name, number, etc. is displayed. Lower-case characters and special characters cannot be displayed.
Page 634 ® 3-3. Using the Bluetooth audio system Microphone ■...
Page 635 ® 3-3. Using the Bluetooth audio system Operating the system using voice commands By following voice guidance instructions output from the speaker, ® voice commands enable the operation of the Bluetooth audio sys- tem without the need to check the display or operate ■...
Page 636 ® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system for the first time ® Before using the Bluetooth audio system, it is necessary to register ® a Bluetooth enabled portable player in the system. Follow the proce- dure below to register (pair) a portable player: Press until “BT AUDIO”...
Page 637 ® 3-3. Using the Bluetooth audio system ® Menu list of the Bluetooth audio system ■ Normal operation Second First menu Third menu Operation detail menu “Pair Audio Registering a portable player Player” “Select Audio Selecting a portable player to Player”...
Page 638 ® 3-3. Using the Bluetooth audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ Situations that the system may not recognize your voice When driving on rough roads ●...
Page 639 ® 3 -3 . U sing t he Blue t oot h a udio syst e m ® Ope rat ing a Blue t oot h e na ble d port a ble pla ye r Power Volume Selector buttons Selecting a track Selecting an album...
Page 640 ® 3-3. Using the Bluetooth audio system Fast-forwarding and reversing tracks Press and hold “ ” or “ ” on Switching the display Press Each time is pressed, the display changes in the following order: Track title Track title/Artist name Track title/Album name Track title/Elapsed time...
Page 641 ® 3 -3 . U sing t he Blue t oot h a udio syst e m ® Se t t ing up a Blue t oot h e na ble d port a ble pla ye r ® Registering a portable player in the Bluetooth audio system allows the system to function.
Page 642 ® 3-3. Using the Bluetooth audio system Registering a portable player Select “Pair Audio Player” using a voice command or , and per- form the procedure for registering a portable player. ( P. 315) Selecting a portable player to be used Select “Select Audio Player”...
Page 643 ® 3-3. Using the Bluetooth audio system Changing the registered name of a portable player Select “Change Name” using a voice command or Select the name of the portable player to be changed by either of the following methods, and select “Confirm” using a voice command or a.
Page 644 ® 3-3. Using the Bluetooth audio system Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players will be read aloud. When listing is complete, the system returns to “BT• A Setup”. Pressing the talk switch while the name of a portable player is being read aloud selects the portable player, and the following functions will become available:...
Page 645 ® 3-3. Using the Bluetooth audio system Deleting a registered portable player Select “Delete Audio Player” using a voice command or Select the portable player to be deleted by either of the follow- ing methods and select “Confirm” using a voice command or a.
Page 646 ® 3 -3 . U sing t he Blue t oot h a udio syst e m ® Blue t oot h a udio syst e m se t up System setup items and operation procedures ■ ● Setting voice guidance volume 1.
Page 647 3 -4 . U sing t he ha nds-fre e phone syst e m (for c e llula r phone ) H a nds-fre e phone syst e m fe at ure s ® This system supports Bluetooth , which allows you to make or receive calls without using cables to connect a cellular phone and the system, and without operating the cellular phone.
Page 648 3-4. Using the hands-free phone system (for cellular phone) Title Page Using the hands-free phone system ■ Operating the system by using a voice command ■ Using the hands-free phone system for P. 330 the first time ■ Menu list of the hands-free phone sys- Making a phone call ■...
Page 649 ● OPP (Object Push Profile) Ver. 1.1 For detailed information about Hands-free Phone System ■ For assistance with pairing and operating your cell phone, go to the website www.toyota.letstalk.com. ® ■ About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG. Inc.
Page 650 3-4. Using the hands-free phone system (for cellular phone) CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio frequency exposure. This device is approved for Mobile Application only and, to comply with applicable FCC radio frequency exposure regula- tions, must be used with a distance of at least 7.9 in.
Page 651 3 -4 . U sing t he ha nds-fre e phone syst e m (for c e llula r phone ) U sing t he ha nds-fre e phone syst e m Audio unit ■ Display A message, name, phone number, etc.
Page 652 3-4. Using the hands-free phone system (for cellular phone) Steering wheel ■ Volume The voice guidance volume cannot be adjusted using this button. Off-hook switch Turns the hands-free sys- tem on/starts a call On-hook switch Turns the hands-free sys- tem off/ends a call/refuses a call Talk switch Turns the voice command...
Page 653 3-4. Using the hands-free phone system (for cellular phone) Microphone ■...
Page 654 3-4. Using the hands-free phone system (for cellular phone) Operating the system by using a voice command By following voice guidance instructions output from the speaker, voice commands enable the operation of the hands-free phone sys- tem without the need to check the display or operate ■...
Page 655 3-4. Using the hands-free phone system (for cellular phone) Register a phone name by either of the following methods. a. Select “Record Name” by using , and say a name to be registered. b. Press the talk switch and say a name to be registered. A voice guidance instruction to confirm the input is heard.
Page 656 3-4. Using the hands-free phone system (for cellular phone) Menu list of the hands-free phone system ■ Normal operation Second First menu Third menu Operation detail menu Dialing a number stored in “Callback” the incoming call history memory Dialing a number stored in “Redial”...
Page 657 3-4. Using the hands-free phone system (for cellular phone) Second First menu Third menu Operation detail menu “Set PIN” Setting a PIN code “Phonebook Locking the phone book “Security” Lock” “Phonebook Unlocking the phone book Unlock” Registering the cellular phone “Pair Phone”...
Page 658 3-4. Using the hands-free phone system (for cellular phone) ■ Using a short cut key First menu Second menu Operation detail Dialing a number registered “Dial XXX (name)” in the phone book “Dial XXX (number)” Dialing the input numbers “Phone book add Adding a new number entry”...
Page 659 3-4. Using the hands-free phone system (for cellular phone) ■ Automatic volume adjustment When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less. ■...
Page 660 3 -4 . U sing t he ha nds-fre e phone syst e m (for c e llula r phone ) M a k ing a phone c a ll Making a phone call ■ ● Dialing by inputting a number “Dial by number”...
Page 661 3-4. Using the hands-free phone system (for cellular phone) Dialing by inputting a number Press the talk switch and say “Dial by number”. Press the talk switch and say the phone number. Dial by one of the following methods: a. Press the off-hook switch. b.
Page 662 3-4. Using the hands-free phone system (for cellular phone) When receiving a phone call ■ Answering the phone Press the off-hook switch. Refusing the call ■ Press the on-hook switch. Transferring a call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call.
Page 663 3-4. Using the hands-free phone system (for cellular phone) Using the call history memory Follow the procedure below to use a number stored in the call history memory: Press the talk switch and say “Redial” (when using a number stored in the outgoing call history memory) or “Call back” (when using a number stored in the incoming call history memory).
Page 664 3-4. Using the hands-free phone system (for cellular phone) ■ Call history Up to 5 numbers can be stored in each of the outgoing and incoming call his- tory memories. When talking on the phone ■ ● Do not talk simultaneously with the other party. ●...
Page 665 3 -4 . U sing t he ha nds-fre e phone syst e m (for c e llula r phone ) Se t t ing a c e llula r phone Registering a cellular phone in the hands-free phone system allows the system to function.
Page 666 3-4. Using the hands-free phone system (for cellular phone) Registering a cellular phone Select “Pair Phone” by using a voice command or , and do the procedure for registering a cellular phone. ( P. 333) Selecting the cellular phone to be used Select “Select Phone”...
Page 667 3-4. Using the hands-free phone system (for cellular phone) Changing a registered name Select “Change Name” by using a voice command or Select the name of the cellular phone to be changed by either of the following methods: a. Press the talk switch and say the desired phone name, and select “Confirm”...
Page 668 3-4. Using the hands-free phone system (for cellular phone) Listing the registered cellular phones Selecting “List Phones” by using a voice command or causes the list of registered cellular phones to be read aloud. When listing is complete, the system returns to “Phone Setup”. Pressing the talk switch while the name of a cellular phone is being read selects the cellular phone, and the following functions will be available:...
Page 669 3-4. Using the hands-free phone system (for cellular phone) Changing the passkey Select “Set Passkey” by using a voice command or Press the talk switch, say a 4 to 8-digit number, and select “Confirm” by using a voice command or The number should be input 1 digit at a time.
Page 670 3-4. Using the hands-free phone system (for cellular phone) ■ Turning on the automatic connection Select “Handsfree Power” by using a voice command or Select “Turn on” by using a voice command or ■ The number of cellular phones that can be registered Up to 6 cellular phones can be registered in the system.
Page 671 3 -4 . U sing t he ha nds-fre e phone syst e m (for c e llula r phone ) Se c urit y a nd syst e m se t up To enter the menu of each setting, follow the steps below: Security setting items and operation procedure ■...
Page 672 3-4. Using the hands-free phone system (for cellular phone) Setting or changing the PIN ■ Setting a PIN Select “Set PIN” by using a voice command or Enter a PIN by using a voice command or When using , input the code 1 digit at a time. ■...
Page 673 3-4. Using the hands-free phone system (for cellular phone) Locking or unlocking the phone book Select “Phonebook lock” or “Phonebook unlock” by using a voice command or Input the PIN by either of the following methods and select “Confirm” by using a voice command or a.
Page 674 3-4. Using the hands-free phone system (for cellular phone) ® Displaying the Bluetooth device address and name Select “Device Name” using ® Turn to display the Bluetooth device address and name. Select “Go Back” using to return to “System Setup”. Initialization Select “Initialize”...
Page 675 3-4. Using the hands-free phone system (for cellular phone) ■ Initialization The following data in the system can be initialized: ● • Phone book • Outgoing and incoming call history • Speed dials • Registered cellular phone data • Security code Once the initialization has been completed, the data cannot be restored ●...
Page 676 3 -4 . U sing t he ha nds-fre e phone syst e m (for c e llula r phone ) U sing t he phone book To enter the menu of each setting, follow the steps below: ● Adding a new phone number 1.
Page 677 3-4. Using the hands-free phone system (for cellular phone) ■ Adding procedure Select “Add Entry” by using a voice command or Use one of the following methods to input a telephone num- ber: Inputting a telephone number by using a voice command STEP2-1 Select “By Voice”...
Page 678 3-4. Using the hands-free phone system (for cellular phone) Inputting a phone number by using STEP2-1 Select “Manual Input” by using STEP2-2 Input a phone number by using , and press once again. Input the phone number 1 digit at a time. Selecting a phone number from outgoing or incoming call history STEP2-1 Select “Call History”...
Page 679 3-4. Using the hands-free phone system (for cellular phone) Select the name to be registered by either of the following methods, and select “Confirm” by using a voice command or a. Press the talk switch and say the desired name. b.
Page 680 3-4. Using the hands-free phone system (for cellular phone) Setting speed dials Select “Set Speed Dial (Speed Dial)” by using a voice com- mand or Select the data to be registered as a speed dial by either of the following methods: a.
Page 681 3-4. Using the hands-free phone system (for cellular phone) Changing a registered name Select “Change Name” by using a voice command or Select the name to be changed by either of the following methods. a. Press the talk switch, say desired name, and select “Confirm”...
Page 682 3-4. Using the hands-free phone system (for cellular phone) Deleting registered data Select “Delete Entry” by using a voice command or Select the data to be deleted by either of the following meth- ods, and select “Confirm” by using a voice command or a.
Page 683 3-4. Using the hands-free phone system (for cellular phone) Listing the registered data Selecting “List names” by using a voice command causes a list of the registered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch while the desired data is being read aloud selects the data, and the following functions will be available.
Page 684 3 -5 . U sing t he int e rior light s I nt e rior light s list Interior light ( P. 364) Personal lights (Access Cab and Double Cab models) ( P. 364) ■ Illuminated entry system When the interior light switch is in the DOOR position, the interior light auto- matically turns on/off according to whether the doors are locked/unlocked and whether the doors are open/closed.
Page 685 3-5. Using the interior lights Interior light and personal lights Interior light DOOR position Personal lights (Access Cab and Double Cab models) On/off...
Page 686 3 -6 . U sing t he st ora ge fe a t ure s List of st ora ge fe at ure s Glove box Overhead console (Access Cab and Double Cab models) Bottle holders Auxiliary boxes Front console box (separated type front seat only) Cup holders CAUTION ■...
Page 687 3-6. Using the storage features Glove box and front console box Glove box Pull up the lever. CAUTION ■ Caution while driving Keep the glove box closed. Injuries may result in the event of an accident or sudden braking. Front console box (Separated type front seat only) Push the button.
Page 688 3-6. Using the storage features Cup holders Cup holders Type A (Bench type front seat) Type B (Separated type front seats with an automatic transmis- sion) Type C (Separated type front seats with a manual transmission)
Page 689 3-6. Using the storage features Cup holders ■ Removing the cup holder Type A (Bench type front seat) Pull the cup holder up. Type B (Separated type front seats with an automatic transmission) Pull the cup holder up. CAUTION Items unsuitable for the cup holder ■...
Page 690 3-6. Using the storage features Bottle holders Bottle holders Front Front console box (Separated type front seat) Rear (Double Cab models) ■ Bottle holders Depending on their size or shape, some bottles may not fit in the holders.
Page 691 3-6. Using the storage features Bottle holders and auxiliary boxes NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
Page 692 3-6. Using the storage features Auxiliary boxes Turn the knob counterclockwise. Open the lid. Press the lid against the bot- tom of the lower cushion until it is supported by the hook- and-loop fastener. Make sure that the lid is sup- ported to prevent it from closing unexpectedly.
Page 693 3-6. Using the storage features Auxiliary boxes and overhead console CAUTION ■ Caution while driving Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking. Overhead console (Access Cab and Double Cab models) The overhead console is useful for temporarily storing sunglasses and similar small items.
Page 694 3 -7 . Ot he r int e rior fe a t ure s Sun visors Type A Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Type B Forward position: Flip down. Side position: Flip down, unhook, and swing to the side.
Page 695 3 -7 . Ot he r int e rior fe a t ure s Va nit y m irrors Vehicles without vanity light Vehicles with vanity light Slide the cover. The light turns on when the cover is opened.
Page 696 3 -7 . Ot he r int e rior fe a t ure s Clock Adjusts the hours Adjusts the minutes ■ The clock is displayed when The engine switch is in the ACC or ON position. ■ When disconnecting and reconnecting battery terminals The time display will automatically be set to 1:00.
Page 697 3 -7 . Ot he r int e rior fe a t ure s Outside temperature display (vehicles with auto anti-glare inside rear view mirror) The temperature display shows temperatures within the ranges of -40° F (-40° C) an d 122° F (50° C). Outside temperature display ■...
Page 698 3-7. Other interior features Changing the display The outside temperature display on the inside rear view mirror can be turned on/off and the display units can be changed. Turning the outside temperature display on/off ■ Type A: Press and hold to display “Custom Settings Menu”.
Page 699 3-7. Other interior features ■ Changing display units Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Menu”. Type A: Press and select “Outside Temperature”, then press and hold Type B: Press and select “Outside Temperature”, then press...
Page 700 3-7. Other interior features Setting the ice advisory indicator The ice advisory indicator on the inside rear view mirror can be turned on/off. Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Menu”. Type A: Press and select “Ice Advisory”.
Page 701 When “– –” or “– – –” is displayed ■ The system may be malfunctioning. Take your vehicle to your Toyota dealer. ■ Customization that can be configured for the inside rear view mirror display Settings (e.g.
Page 702 3 -7 . Ot he r int e rior fe a t ure s Pow e r out le t s (1 2 V DC) The power outlets can be used for 12V accessories that run on less than 10A. ■...
Page 703 3 -7 . Ot he r int e rior fe a t ure s Pow e r out le t (1 2 0 V AC) The power outlet can be used for electrical appliances. Main switch To use the power outlet, turn on the main switch. The power supply starts a few seconds after the main switch is pressed.
Page 704 3-7. Other interior features • The shift lever is in N and the clutch pedal is not depressed. (manual transmission) A maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again under condi- tion described above.
Page 705 When the cabin temperature is high, open the windows to cool the tempera- ture down. Once it reaches the normal temperature, turn the power outlet main switch on again. If the power supply is not resumed even after performing the above proce- dure, have the vehicle inspected by a Toyota dealer.
Page 706 Do not modify, disassemble or repair the power outlet or its inverter, in any ● way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs. ■...
Page 707 3-7. Other interior features NOTICE ■ To avoid damaging the power outlet and the plug ● Close the power outlet lid when not in use. Foreign objects or liquids that enter the power outlet may cause a short ● circuit. ●...
Page 708 If the power outlet is loose when an electrical appliance plug is con- nected Replace the outlet. Contact a Toyota dealer for any necessary replacements. If the power outlet gets dirty ■ Turn the main switch off and use a soft, clean cloth to wipe it gently.
Page 709 3 -7 . Ot he r int e rior fe a t ure s Se at ba ck t a ble Front passenger’s seatback can be used as a temporary table only when the vehicle is stopped. Fold down the front passen- ger’s seat to use the seatback table.
Page 710 3 -7 . Ot he r int e rior fe a t ure s Floor m at Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.
Page 711 ■ ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver’s seat. Always install the floor mat securely using the retaining hooks (clips) pro- ●...
Page 712 3 -7 . Ot he r int e rior fe a t ure s Lugga ge c om pa r t m e nt fe at ure s Behind the rear seat (Double Cab models only) Cargo net hooks (vehicles with sub woofer) Grocery bag hooks Flashlight holder Storage boxes...
Page 713 3-7. Other interior features Auxiliary boxes Left side Turn the knob counterclock- wise. Open the lid. Right side (vehicles without 120V power outlet) Turn the knob counterclock- wise. Open the lid. Right side (vehicles with 120V power outlet) Turn the knob counterclock- wise.
Page 714 3-7. Other interior features CAUTION ■ Caution while driving Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking. Deck hooks Deck hooks are provided for securing loose items. CAUTION ■ When not in use Keep the deck hooks folded.
Page 715 3-7. Other interior features Tie-down cleats The deck rail system enables you to insert and move tie-down cleats to their best location along deck rails to secure a load. Locking plate Thumb wheel Tie-down cleat ■ Installing the tie-down cleat Loosen the thumb wheel in a counterclockwise motion, and depress the wheel so that the...
Page 716 3-7. Other interior features Insert the locking plate into the deck rail, rotate the tie-down cleat 90° , and release the thumb wheel. Slide the cleat to the closest detent in the rail system. You will feel that the locking plate snaps into a detent.
Page 717 3-7. Other interior features CAUTION ■ Tie-down cleat precautions ● Properly install and tighten the tie-down cleats into the deck rail system. Failure to properly install and tighten the tie-down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehi- cle is in motion.
Page 718 3-7. Other interior features Left side Removing the separator ■ Remove the separator. It can be installed in various positions as required. Flashlight holder (Double Cab models only) Flashlight holder is designed to hold the flashlight securely.
Page 719 3-7. Other interior features ■ Removing the flashlight holder Remove the flashlight holder. It can be installed in various positions as required. Grocery bag hooks (Double Cab models only) Grocery bag hook is designed to hang things like grocery bag. NOTICE Grocery bag hook weight capacity ■...
Page 720 3-7. Other interior features Cargo net hooks (Double Cab models with sub woofer) Cargo net hooks are designed to hang the factory-supplied cargo net. NOTICE ■ To prevent damage to the cargo net hook Do not hang items other than the cargo net.
Page 721 3 -7 . Ot he r int e rior fe a t ure s Ga ra ge door ope ne r The garage door opener can be trained to operate garage doors, gates, entry doors, door locks, home lighting systems, security sys- tems, and other devices.
Page 722 3-7. Other interior features ® ■ Training the HomeLink Point the remote control trans- mitter for the device 1 to 3 in. (25 ® to 75 mm) from the HomeLink control buttons. Keep indicator ® HomeLink in view while training. Press and hold down one of the ®...
Page 723 3-7. Other interior features Test operation ® HomeLink pressing newly trained button. If training a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the Rolling Code type.
Page 724 3-7. Other interior features ■ Training a Rolling Code system (for U.S. owners) If your device is Rolling Code equipped, follow the steps under the ® heading “Training the HomeLink ” before proceeding with the steps listed below. Locate the learn button on the ceiling mounted garage door opener motor.
Page 725 HomeLink buttons. ■ Training other devices To train other devices such as home security systems, home door locks and lighting, contact your Toyota dealer for assistance. Retraining a button ■ ® The individual HomeLink buttons cannot be erased but can be ®...
Page 726 3-7. Other interior features ® Operating HomeLink ® ® Press the appropriate HomeLink button. The HomeLink indicator light should come on. ® The HomeLink compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed. ®...
Page 727 3-7. Other interior features ■ Before training Install a new battery in the remote control transmitter. ● ● The battery side of the remote control transmitter must be pointed away ® from the HomeLink button. ■ Certification for the garage door opener FCC ID: NZLGHSHL4 For vehicles sold in the U.S.A.
Page 728 3-7. Other interior features ■ If the following message is displayed This message appears when training procedures have not been performed correctly. Follow the instructions on the screen to complete or cancel train- ing. Pattern A Pattern B ■ When support is necessary Visit on the web at www.homelink.com or call 1-800-355-3515.
Page 729 3-7. Other interior features CAUTION ■ When training a garage door or other remote control devices The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm. ■ Conforming to federal safety standards ®...
Page 730 3 -7 . Ot he r int e rior fe a t ure s Compass (vehicles w ith auto anti-glare inside rear view mirror) The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. Location ■...
Page 731 3-7. Other interior features Displays and directions ■ Display Direction North Northeast East Southeast South Southwest West Northwest...
Page 732 3-7. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies depending on the geographic position of the vehicle. If you cross over one of the map boundaries shown in the illustration, the compass will deviate.
Page 733 3-7. Other interior features Type A: Press and select “Compass”, then press and hold Type B: Press and select “Compass”, then press Type A: Press and select “Compass Display”. Type B: Press and select “Compass Display”. Type A: Press and hold and select display on/off.
Page 734 3-7. Other interior features Type A: Press and select “Zone”, then press and hold Type B: Press and select “Zone”, then press Type A: The selected country changes each time is pressed. Select the country, then press and hold confirm. Type B: The selected country changes each...
Page 735 3-7. Other interior features Circling calibration If “C” appears on the display, circling calibration needs to be per- formed. Stop the vehicle in a place where it is safe to drive in a circle. Type A: Press and hold to display “Custom Settings Menu”.
Page 736 3-7. Other interior features Drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed. If there is not enough space to drive in a circle, drive around the block until a direction is dis- played.
Page 737 3-7. Other interior features CAUTION ■ While driving the vehicle Do not adjust the display. Adjust the display only when the vehicle is stopped. ■ When doing the circling calibration Secure a wide space, and watch out for people and vehicles in the vicinity. Do not violate any local traffic rules while performing circling calibration.
Page 738 4 -1 . M a int e na nc e a nd c a re Cle a ning a nd prot e c t ing t he ve hicle ex t e rior Perform the following to protect the vehicle and maintain it in prime condition.
Page 739 4-1. Maintenance and care ■ Aluminum or chrome cladded wheels (if equipped) Remove any dirt immediately by using a neutral detergent. Do not use ● hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint. Do not use detergent on the wheels when they are hot, for example after ●...
Page 740 4-1. Maintenance and care NOTICE ● Clean the drainage hole of the deck regularly. If the drainage hole is stopped up, the water will not be able to flow, and it will cause rust. Cleaning the exterior lights ■ ● Wash carefully.
Page 741 ● Allow the solution to soak in for a few minutes. Remove the dirt and wipe off the solution with a clean, damp cloth. ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.
Page 742 4-1. Maintenance and care ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained when keeping the carpet as dry as possible.
Page 743 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. ●...
Page 744 Repair and replacement ■ It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the war-...
Page 745 4-2. Maintenance ■ Allow inspection and repairs to be performed by a Toyota dealer Toyota technicians are well-trained specialists and are kept up to date ● with the latest service information. They are well informed about the operations of all systems on your vehicle.
Page 746 “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
Page 747 4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be hold securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 748 4-2. Maintenance Items Check points • Moves smoothly? Steering wheel • Has correct free play? • No strange noises? Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? •...
Page 749 If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
Page 750 • FMVSS No.116 DOT 3 or SAE Brake fluid level ( P. 444) J1703 brake fluid • Rag or paper towel • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 751 4-3. Do-it-yourself maintenance Items Parts and tools • Bulb with same number and watt- age rating as original Light bulbs ( P. 484) • Phillips-head screwdriver • Conventional wrench • Automatic transmission fluid Power steering fluid level ® DEXRON II or III ( P.
Page 752 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothing, and tools away from the moving fan and engine drive belt.
Page 753 4-3. Do-it-yourself maintenance NOTICE ■ If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment. ■...
Page 754 4 -3 . Do-it -yourse lf m a int e na nc e H ood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. The hood will pop up slightly. Pull up the hood catch lever and lift the hood.
Page 755 4-3. Do-it-yourself maintenance Hold the hood open by insert- ing the supporting rod into the slot. CAUTION ■ Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
Page 756 4 -3 . Do-it -yourse lf m a int e na nc e Engine c om pa r t m e nt 2.7 L 4-cylinder (2TR-FE) engine Washer fluid tank ( P. 450) Engine oil level dipstick ( P. 438) Radiator cap Brake fluid reservoir Engine coolant reservoir...
Page 757 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Washer fluid tank ( P. 450) Engine oil filler cap ( P. 439) Power steering fluid reservoir ( P. 446) Brake fluid reservoir ( P. 444) Radiator cap Fuse box ( P. 474) Engine oil level dipstick ( P.
Page 758 4-3. Do-it-yourself maintenance Engine oil Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil ■ Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Page 759 4-3. Do-it-yourself maintenance 2.7 L 4-cylinder (2TR-FE) engine Full 4.0 L V6 (1GR-FE) engine Full ■ Adding engine oil 2.7 L 4-cylinder (2TR-FE) engine If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Page 760 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Make sure to check the oil type and prepare the items needed before adding oil. Engine oil selection P. 556 Items Clean funnel Remove the oil filler cap, turning it counterclockwise. Add engine oil slowly. Checking the dipstick.
Page 761 ● If you consume more than 1.1 qt. (1.0 L, 0.9 lmp.qt.) every 600 miles (1000 km), contact your Toyota dealer. After changing the engine oil (U.S.A. only) ■ The engine oil maintenance data should be reset. Perform the following pro- cedures: Switch the display to the trip meter A when the engine is running.
Page 762 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 763 If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system. Coolant selection ■...
Page 764 Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION ■...
Page 765 4-3. Do-it-yourself maintenance Type B MAX line MIN line Adding fluid ■ Make sure to check the fluid type and prepare the necessary items. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Rag or paper towel Type B only Turn the engine off.
Page 766 4-3. Do-it-yourself maintenance CAUTION ■ When filling the reservoir Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately.
Page 767 4-3. Do-it-yourself maintenance Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures. (Fluid temperature, 104° F - 175° F [40° C - 80° C]) Cold: Engine has not been run for about 5 hours. (Room tem- perature, 32°...
Page 768 4-3. Do-it-yourself maintenance CAUTION ■ Checking the fluid level Take care, as the reservoir may be hot. NOTICE When adding fluid ■ Avoid overfilling, or the power steering may be damaged. After replacing the reservoir cap ■ Check the steering box case, vane pump and hose connections for leaks or damage.
Page 769 4-3. Do-it-yourself maintenance ■ Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: If recharging with the battery installed on the vehicle, be sure to discon- ● nect the ground cable. ● Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
Page 770 4-3. Do-it-yourself maintenance CAUTION ■ Emergency measures regarding electrolyte ● If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
Page 771 4-3. Do-it-yourself maintenance Add washer fluid. CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE Do not use any fluid other than washer fluid ■...
Page 772 ■ The tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. ( P. 508)
Page 773 Have tire pressure warning valve and trans- mitter ID codes registered by your Toyota dealer. ( P. 454) Initializing the tire pressure warning system The tire pressure warning system must be initialized in the fol- ■...
Page 774 The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.
Page 775 A tire goes flat repeatedly or cannot be properly repaired due to the ● size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. Replacing tires and wheels ■ If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
Page 776 4-3. Do-it-yourself maintenance Access Cab models Tire types ■ 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 777 If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. When operating the tire pressure warning reset switch, the tire pres- ●...
Page 778 4-3. Do-it-yourself maintenance Tire pressure warning system certification ■ FCC ID: PAXPMV107J PAXPMV108J FCC ID: HYQ13BCX For vehicles sold in U.S.A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 779 Do not mix tires of different makes, models or tread patterns. ● Also, do not mix tires of remarkably different treadwear. Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply ●...
Page 780 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 781 4 -3 . Do-it -yourse lf m a int e na nc e T ire inflat ion pre ssure Tire inflation pressure ■ The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. ( P. 564) Regular Cab and Double Cab models...
Page 782 4-3. Do-it-yourself maintenance Access Cab models...
Page 783 4-3. Do-it-yourself maintenance Inspection and adjustment procedure ■ Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.
Page 784 Reduced safety ● Damage to the drive train ● If a tire needs frequent refilling, have it checked by your Toyota dealer. Instructions for checking tire inflation pressure ■ When checking tire inflation pressure, observe the following: Check only when the tires are cold.
Page 785 4-3. Do-it-yourself maintenance CAUTION Proper inflation is critical to save tire performance ■ Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. Excessive wear ● Uneven wear ● Poor handling ●...
Page 786 ● Bent wheels that have been straightened Wheel precautions ■ ● Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).
Page 787 When replacing wheels ■ The wheels of your Toyota are equipped with tire pressure warning valves and transmitters (except for spare tire) that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure.
Page 788 Because tire repair or replacement may affect the tire pressure warn- ● ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 789 4 -3 . Do-it -yourse lf m a int e na nc e Air c ondit ioning filt e r The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method ■ Turn the engine switch to the LOCK position. Open the glove box.
Page 790 4-3. Do-it-yourself maintenance Open the filter door. Remove the filter. Replacement method ■ Remove the air conditioning filter and replace it with a new one. When installing the filter, follow the instructions indicated on the label.
Page 791 4-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) ■...
Page 792 4 -3 . Do-it -yourse lf m a int e na nc e Wire le ss re m ot e c ont rol bat t e r y Replace the battery with a new one if it is discharged. ■ You will need the following items: Lithium battery CR2032 ■...
Page 793 ● The operational range is reduced. Use a CR2032 lithium battery ■ ● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. ● Replace only with the same or equivalent type recommended by your Toyota dealer. ●...
Page 794 4 -3 . Do-it -yourse lf m a int e na nc e Che ck ing a nd re pla c ing fuse s If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch to the LOCK position.
Page 795 4-3. Do-it-yourself maintenance After a system failure, see “Fuse layout and amperage ratings” ( P. 477) for details about which fuse to check. Remove the fuse with the pull- out tool. Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 796 4-3. Do-it-yourself maintenance Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type C Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 797 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment Type A Type B...
Page 798 4-3. Do-it-yourself maintenance Fuse Ampere Circuit 10 A Air conditioning system TOWING TAIL 30 A Trailer lights (tail lights) FR FOG 15 A Front fog lights Stop lights, high mounted stop- light, vehicle stability control sys- tem, anti-lock brake system, shift STOP 10 A lock system, multiport fuel injection...
Page 799 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiport fuel injection system/ 20 A sequential multiport fuel injection system HORN 10 A Horn Multiport fuel injection system/ A/F HEATER 15 A sequential multiport fuel injection system Wireless remote control system, air conditioning system, multiplex communication system, meter and ECU-B 7.5 A...
Page 800 4-3. Do-it-yourself maintenance Fuse Ampere Circuit IGN and GAUGE fuses, multiport 30 A fuel injection system/sequential multiport fuel injection system Multiport fuel injection system/ A/PUMP 50 A sequential multiport fuel injection system Anti-lock brake system, vehicle sta- ABS NO.2 30 A bility control system AC SKT 100 A...
Page 801 4-3. Do-it-yourself maintenance ■ Under the instrument panel Fuse Ampere Circuit Multiport fuel injection system/ sequential multiport fuel injection system, anti-lock brake system, 15 A traction control system, vehicle sta- bility control system, SRS airbag system, front passenger occupant classification system Meter and gauge, emergency GAUGE 7.5 A...
Page 802 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Anti-lock brake system, vehicle sta- bility control system, stop lights, charging system, multiport fuel injection system/sequential multi- port fuel injection system, air condi- IG1 NO.2 10 A tioning system, instrument panel light control, anti-glare inside rear view mirror, back monitor, clutch start cancel switch, rear differential lock system, power outlets, tire...
Page 803 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. ● Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.
Page 804 You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 805 4-3. Do-it-yourself maintenance Rear bulb locations ■ High mounted stoplight Rear turn signal lights Stop/tail and rear side Back-up lights marker lights (bulb type only) License plate lights Replacing light bulbs ■ Headlights Unplug the connector.
Page 806 4-3. Do-it-yourself maintenance Remove the rubber cover. Release bulb retaining spring. Remove the bulb. To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole.
Page 807 4-3. Do-it-yourself maintenance ■ Front fog lights (if equipped) Unplug the connector while pull- ing the lock release. Turn the bulb counterclockwise.
Page 808 4-3. Do-it-yourself maintenance ■ Front side marker lights Turn the bulb base counterclock- wise. Remove the light bulb.
Page 809 4-3. Do-it-yourself maintenance ■ Front turn signal lights/parking lights/daytime running lights (if equipped) Turn the bulb base counterclock- wise. Remove the light bulb.
Page 810 4-3. Do-it-yourself maintenance ■ Stop/tail lights, rear side marker lights (bulb type only), back- up lights and rear turn signal lights Remove the bolts and rear com- bination assembly. Unplug connector while depressing the lock release. Turn the bulb bases counter- clockwise.
Page 811 4-3. Do-it-yourself maintenance ■ High mounted stoplight Remove the screws and cover. Remove the light bulbs.
Page 812 4-3. Do-it-yourself maintenance ■ License plate lights Remove the screw and light unit. Turn the bulb base counterclock- wise. Remove the light bulb.
Page 813 Rear side marker lights (LED type) Condensation build-up on the inside of the lens ■ Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction.
Page 814 4-3. Do-it-yourself maintenance...
Page 815 5 -1 . Esse nt ia l inform a t ion Em e rge ncy fla she rs Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again.
Page 816 I f your ve hicle ne e ds t o be t ow e d If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck.
Page 817 5-1. Essential information Type B Towing hook Emergency towing procedure ■ The engine switch must be in the ACC (engine off) or the ON (engine running) position. 4WD models: Put the front-wheel drive control switch in H2. Put the shift lever in N. Release the parking brake.
Page 818 5-1. Essential information NOTICE ■ Emergency towing eyelet/hook precautions ● Before emergency towing, check that the eyelet/hook is not broken or damaged. ● Fasten the towing cable or chain securely to the eyelet/hook. ● Do not jerk the eyelet/hook. Apply steady and even force. ●...
Page 819 5-1. Essential information Towing with a wheel lift-type truck from the front Vehicles with an automatic trans- mission: Use a towing dolly under the rear wheels. 2WD models with a manual transmission: We recommend to use a towing dolly under the rear wheels.
Page 820 5-1. Essential information Towing with a wheel lift-type truck from the rear 2WD models Turn the engine switch to the ACC position. 4WD models We recommend to use a towing dolly under the front wheels. When not using a towing dolly, turn the engine switch to the ACC position, shift the shift lever to N and put the front-wheel drive con-...
Page 821 5-1. Essential information Using a flat bed truck If your Toyota is transported by a Front flat bed truck, it should be tied down at the locations shown in the illustration. If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45 .
Page 822 5 -1 . Esse nt ia l inform a t ion I f you t hink som e t hing is w rong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■...
Page 823 5 -1 . Esse nt ia l inform a t ion Fue l pum p shut off syst e m To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine.
Page 824 Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer)* •...
Page 825 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: •...
Page 826 5-2. Steps to take in an emergency Warning light Warning light/Details SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; • The seat belt pretensioner system. ABS warning light (U.S.A.) Indicates a malfunction in: •...
Page 827 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light Check that all doors Indicates that a door is are closed.
Page 828 Toyota dealer. • When the light stays on Have the system after blinking for 1 checked by your minute: Malfunction in Toyota dealer.
Page 829 Is the fuel tank cap loose? If it is, tighten it securely. The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible. ■...
Page 830 If there is a lot of snow or ice on the vehicle, in particular around the ● wheels or wheel housings. If non-genuine Toyota wheels are used. (Even if you use Toyota ● wheels, the tire pressure warning system may not work properly with some types of tires.)
Page 831 After changing the engine oil (U.S.A. only) Make sure to reset the oil maintenance data. ( P. 441) ■ Customization that can be configured at Toyota dealer The vehicle speed linked seat belt reminder buzzer can be disabled. (Customizable features P.
Page 832 5-2. Steps to take in an emergency CAUTION Maintenance of the tire ■ As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS-tire pressure warning system) that illuminates a low tire pressure telltale (tire pressure warning light) when one or more of your tires is significantly under-inflated.
Page 833 5-2. Steps to take in an emergency NOTICE Precaution when installing a different tire ■ When a tire of a different specification or maker is installed, the tire pres- sure warning system may not operate properly.
Page 834 5 -2 . St e ps t o t a k e in a n e m e rge nc y I f you have a flat t ire Remove the flat tire and replace it with the spare provided. ■...
Page 835 5-2. Steps to take in an emergency Access Cab models Tool bag Jack Double Cab models Tool bag Jack Taking out the jack and tool bag Regular Cab models with bench type seat Pull the lever and fold down the seatback.
Page 836 5-2. Steps to take in an emergency Regular Cab models with separated type seat Pull the lever and fold down the seatback. Unhook the strap and remove the tool bag. Loosen and remove the jack. Loosen Tighten...
Page 837 5-2. Steps to take in an emergency Access Cab models Pull up the lever. Raise the bottom cushion up. Turn the knob counterclockwise. Open the lid. Press the lid against the bot- tom of the lower cushion until it is supported by the hook- and-loop fastener.
Page 838 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Double Cab models Swing the bottom cushion up by pulling the lock release strap. Turn the knob counterclock- wise. Open the lid. Unhook the strap and remove the tool bag.
Page 839 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Assemble the jack handle (in the tool bag) Assemble the jack handle exten- sion as shown. Taking out the spare tire Insert the end of the jack handle extension into lowering...
Page 840 5-2. Steps to take in an emergency After the tire is lowered com- pletely to the ground, remove the holding bracket. Replacing a flat tire Chock the tires. Wheel Flat tire chock positions Behind the Left- rear right- hand hand side side tire Front...
Page 841 5-2. Steps to take in an emergency Remove the wheel ornament using the wheel nut wrench as shown. To protect the wheel and wheel ornament, place a rag between the wrench and the wheel ornament, as shown in the illustration. Type A Type B Type C...
Page 842 5-2. Steps to take in an emergency Slightly loosen the wheel nuts (one turn). Assemble the jack handle exten- sion as shown. Position the jack at the correct jack point as shown. Front Rear Make sure the jack is positioned on a level and solid place.
Page 843 5-2. Steps to take in an emergency Remove all the wheel nuts and the tire. When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface. Installing the tire Remove any dirt or foreign mat- ter from the wheel contact sur- face.
Page 844 5-2. Steps to take in an emergency Replacing an aluminum wheel with a steel wheel Tighten the nuts until the tapered Tapered portion portion comes into loose contact with the disc wheel sheet. Disc wheel sheet Replacing an aluminum wheel with an aluminum wheel Tighten the nuts until the washer Washer of the nut comes into loose con-...
Page 845 5-2. Steps to take in an emergency Firmly tighten each nut two or three times in the order shown in the illustration. Tightening torque: 83 ft·lbf (113 N·m, 11.5 kgf·m) 2WD models except PreRunner 4WD models and PreRunner Stowing the flat tire, jack and all tools Lay down the tire with the outer side facing up, and install the holding bracket.
Page 846 5-2. Steps to take in an emergency 4WD models only: Fasten the claws of the holding bracket into the wheel holes as shown in the illustration. Holding bracket Claw Then secure the tire, taking care that the tire goes straight up without catching on any other part, to prevent it from flying for- ward during a collision or sudden braking.
Page 847 5-2. Steps to take in an emergency CAUTION Using the jack ■ Improper use of the jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. Do not use the jack for any purpose other than replacing tires or install- ●...
Page 848 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • Do not attach a heavily damaged wh eel ornament, as it may fly off the wheel while the vehicle is moving.
Page 849 5-2. Steps to take in an emergency CAUTION Speed limit when using the temporary spare tire ■ Do not drive at speeds in excess of 50 mph (80 km/h) when a temporary spare tire is installed on the vehicle. The temporary spare tire is not designed for driving at high speeds. Fail- ing to observe this precaution may lead to an accident causing death or serious injury.
Page 850 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 851 One of the following may be the cause of the problem. ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. ( P. 535) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
Page 852 (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 853 5 -2 . St e ps t o t a k e in a n e m e rge nc y I f you lose your ke ys New genuine Toyota keys can be made by your Toyota dealer using the other key and the key number stamped on your key number...
Page 854 You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. Connect the jumper cables.
Page 855 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.
Page 856 5-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged (vehicles with an automatic transmission) The engine cannot be started by push-starting. Avoiding a discharged battery ■ ● Turn off the headlights and the audio system while the engine is turned off.
Page 857 5-2. Steps to take in an emergency CAUTION ■ Battery precautions The battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following pre- cautions when handling the battery. ● When working with the battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.
Page 858 If the fan is operating: Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine. If the fan is not operating: Stop the engine immediately and call your local Toyota dealer.
Page 859 Note that water draining from the air conditioning is normal if it has been used. Add engine coolant if required. Water can be used in an emer- gency if engine coolant is unavailable. ( P. 559) Have the vehicle checked at your nearest Toyota dealer as soon as possible.
Page 860 5-2. Steps to take in an emergency ■ Overheating If you observe the following, your vehicle may be overheating. ● The engine coolant temperature gauge enters the red zone or a loss of power is experienced. ● Steam is coming from under the hood. CAUTION ■...
Page 861 5 -2 . St e ps t o t a k e in a n e m e rge nc y I f t he ve hicle be c om e s st uck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow.
Page 862 5-2. Steps to take in an emergency NOTICE ■ To avoid damaging the transmission and other components ● Avoid spinning the wheels and do not rev the engine. If the vehicle remains stuck after trying these procedures, the vehicle may ●...
Page 863 5 -2 . St e ps t o t a k e in a n e m e rge nc y If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmly...
Page 864 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 865 5-2. Steps to take in an emergency...
Page 866 5-2. Steps to take in an emergency...
Page 867 6 -1 . Spe c ific a t ions M a int e na nc e dat a (fue l, oil leve l, e t c .) Dimensions 2WD models except PreRunner Access Cab Cab type Regular Cab Double Cab Except X-Runner X-Runner...
Page 868 2.7 L 4-cylinder Double Cab 950 lb. (430 kg) (2TR-FE) engine : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your Toyota dealer about the weight of accessory parts.
Page 869 (1GR-FE) engine Long deck : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your Toyota dealer about the weight of accessory parts. 4WD models Vehicle capacity Cab type Engine...
Page 870 6-1. Specifications TWR (Trailer Weight Rating) Regular Cab models Driving Model code Engine system TRN220L-TRMDKA TRN220L-TRPDKA 2.7 L 4-cylinder 3500 lb. (1585 kg) (2TR-FE) engine TRN240L-TRMDKA TRN240L-TRPDKA Access Cab models Driving Model code Engine system TRN225L-CRMDKA TRN225L-CRPDKA 2.7 L 4-cylinder TRN245L-CRMDKA 3500 lb.
Page 871 6-1. Specifications Double Cab models Driving Model code Engine system TRN225L-PRPDKA 3400 lb. (1540 kg) 2.7 L 4-cylinder (2TR-FE) engine TRN265L-PRPDKA 3500 lb. (1585 kg) 3500 lb. (1585 kg) GRN245L-PRADKA 6500 lb. (2945 kg) 3500 lb. (1585 kg) GRN245L-PRFDKA 6500 lb. (2945 kg) 3500 lb.
Page 872 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 873 6-1. Specifications ■ Engine number The engine number is stamped on the engine block as shown. 2.7 L 4-cylinder (2TR-FE) engine 4.0 L V6 (1GR-FE) engine...
Page 874 6-1. Specifications Engine 2.7 L 4-cylinder (2TR-FE) engine Model 2TR-FE Type 4-cylinder in line, 4-cycle, gasoline Bore and stroke 3.74 3.74 in. (95.0 95.0 mm) Displacement 164.3 cu.in. (2694 cm Drive belt tension Automatic adjustment Valve clearance (engine cold) Intake Automatic adjustment Exhaust 4.0 L V6 (1GR-FE) engine...
Page 875 6-1. Specifications Lubrication system Oil capacity (Drain and refill - reference Without filter 2.7 L 4-cylinder (2TR-FE) engine 5.4 qt. (5.1 L, 4.5 Imp.qt.) 4.0 L V6 (1GR-FE) engine 2WD models except PreRunner: 4.4 qt. (4.2 L, 3.7 Imp.qt.) 4WD models and PreRunner: 5.2 qt.
Page 876 6-1. Specifications ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC multigrade engine oil Recommended viscosity: 2.7 L 4-cylinder (2TR-FE) engine...
Page 877 6-1. Specifications 4.0 L V6 (1GR-FE) engine SAE 5W-30 SAE 5W-30 is the best choice for good fuel economy and good starting in cold weather. If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced Outside temperature with SAE 5W-30 at the next oil change.
Page 878 10.1 qt. (9.6 L, 8.4 Imp.qt.) Vehicles with a manual transmission 10.3 qt. (9.7 L, 8.5 Imp.qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 879 Oil type and viscosity 75W-85 GL-5 or equivalent Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent oil of matching quality to satisfy the above specification.
Page 880 : The fluid capacity is the quantity of reference. If replacement is necessary, contact your Toyota dealer. NOTICE ■ Automatic transmission fluid type (4-speed models) Using automatic transmission fluid other than “Toyota Genuine ATF Type T-IV” may cause deterioration in shift quality, locking up of your transmission accompanied vibration, ultimately...
Page 881 6-1. Specifications Manual transmission Gear oil capacity (Reference) 2.7 L 4-cylinder (2TR-FE) engine 2WD models 2.7 qt. (2.6 L, 2.3 Imp.qt.) 4WD models 2.3 qt. (2.2 L, 1.9 Imp.qt.) 4.0 L V6 (1GR-FE) engine 1.9 qt. (1.8 L, 1.6 Imp.qt.) Gear oil type Gear oil API GL-4 or GL-5 Recommended gear oil viscosity...
Page 882 6-1. Specifications Brakes Pedal clearance 2WD models except 4.3 in. (110 mm) PreRunner PreRunner 4.2 in. (106 mm) 4WD models Without off-road package 4.2 in. (106 mm) With off-road package 3.4 in. (88 mm) Pedal free play 0.04 0.24 in. (1 6 mm) Brake pad wear limit 0.04 in.
Page 883 6-1. Specifications Steering Free play Less than 1.2 in. (30 mm) ® Automatic transmission fluid DEXRON II or Power steering fluid type Tires and wheels Type A Tire size P215/70R15 97S Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Rear tires: 33 psi (230 kPa, 2.3 kgf/cm or bar)
Page 884 6-1. Specifications Type B Tire size P245/75R16 109S Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Rear tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Spare tire: Tire inflation pressure 30 psi (210 kPa, 2.1 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 885 6-1. Specifications Type D Tire size P265/65R17 110S Front tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Rear tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Spare tire: Tire inflation pressure 29 psi (200 kPa, 2.0 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 886 6-1. Specifications Type F Tire size P265/60R18 109H Front tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Rear tires: 29 psi (200 kPa, 2.0 kgf/cm or bar) Spare tire: Tire inflation pressure 29 psi (200 kPa, 2.0 kgf/cm or bar) (Recommended cold tire Driving at high speeds above 100 mph inflation pressure)
Page 887 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights — 60/55 Front fog lights — Front side marker — lights Front turn signal lights/parking lights/ 4157 27/8 daytime running lights Exterior Rear turn signal lights 3157A 27/8 Stop/tail and rear side 3157KX 27/8 marker lights...
Page 888 ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. ■...
Page 889 10% ethanol). (85% ethanol) ● If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87. ● Toyota does not recommend the use of gasoline containing methanol.
Page 890 (Methylcyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.
Page 891 6 -1 . Spe c ific a t ions T ire infor m at ion Typical tire symbols Tire size ( P. 574) DOT and Tire Identification Number (TIN) ( P. 573) Location of treadwear indicators ( P. 452) Tire ply composition and materials Plies are layers of rubber-coated parallel cords.
Page 892 6-1. Specifications Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. Summer tire or all season tire ( P. 456) An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.
Page 893 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol...
Page 894 U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 895 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
Page 896 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Glossary of tire terminology Tire related term Meaning...
Page 897 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as Occupant distribution specified in the third column of Table 1 below The combined weight of installed regular production options weighing over 5 lb.
Page 898 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 899 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on Intended outboard the other sidewall of the tire, or sidewall...
Page 900 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between Ply separation adjacent plies A mechanical device made of rubber, chemicals, fabric and steel or other materials, Pneumatic tire that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that...
Page 901 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear designed to give a visual indication of the...
Page 902 Toyota dealership. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customizing inside rear view mirror features (vehicles with auto anti-glare inside rear view mirror)
Page 903 6-2. Customization Type A: Press and select “Layout”. Type B: Press and select “Layout”. Type A: Press and hold and choose whether outside temperature or compass display will appear on top. Type B: Press and choose whether outside tempera- ture or compass display will appear on top. To leave the “Custom Settings Menu”, select “Back to main menu”...
Page 904 6-2. Customization Type A: Each time is pressed and held, the display col- ors change in the following order: “Green” “White” “Orange” “Blue” Type B: Each time is pressed, the display colors change in the following order: “Green” “White” “Orange” “Blue”...
Page 905 6-2. Customization To leave the “Custom Settings Menu”, select “Back to main menu” to return to the starting screen, then either select “Exit” or wait several seconds without pressing any buttons. Customizable features Customized Item Function Default setting setting Wireless remote con- Operation signal trol...
Page 906 6 -2 . Cust om iza t ion I t e m s t o init ia lize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle.
Page 907 6-2. Customization...
Page 908 If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 909 Seat belt instructions for Canadian ow ners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.
Page 911 SRS airbag instructions for Canadian ow ners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English.
Page 913 For owners...
Page 915 For owners...
Page 917 For owners...
Page 919 For owners...
Page 921 For owners...
Page 922 National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchas- ers and/or prospective purchasers of Toyota vehicles with infor- mation on truck-camper loading. Your Toyota dealer will help answer any questions you may have as you read this informa- tion.
Page 923 CAUTION Loading precaution ■ If a load is too far back, it can cause dangerous handling. If it is too far forward, the front axle may be overloaded. Cargo weight rating and proper matching When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the manufacturer’s camper weight figure, the weight of installed additional camper equipment not included in the manufacturer’s camper weight figure, the weight of camper cargo,...
Page 924 Access Cab models 2 people, 2TR-FE engine, 2WD except PreRunner: 750 lb. (340 kg) 4 people, 2TR-FE engine, 2WD except PreRunner: 450 lb. (204 kg) 2 people, 2TR-FE engine, PreRunner: 1000 lb. (453 kg) 4 people, 2TR-FE engine, PreRunner: 700 lb. (317 kg) 2 people, 1GR-FE engine, PreRunner: 950 lb.
Page 925 Gross axle and vehicle weight ratings Secure loose items to prevent weight shifts that could affect the bal- ance of your vehicle. When the truck camper is loaded, drive to a scale and weigh on the front and on the rear wheels separately to determine axle loads.
Page 926 GAWR ■ GAWR Front Rear 2WD models except PreRun- 2380 lb. (1075 kg) 2650 lb. (1200 kg) Regular Cab models 3000 lb. (1360 kg) 4WD models and 2755 lb. (1245 kg) Access Cab and PreRunner Double Cab models 3110 lb. (1410 kg) GVWR ■...
Page 927 PreRunner Cab type GVWR Vehicles with 2.7 L 4-cylinder (2TR-FE) Access Cab engine 5250 lb. (2380 kg) Vehicles with 4.0 L V6 (1GR-FE) engine Double Cab 5400 lb. (2445 kg) 4WD models Cab type GVWR Regular Cab 5100 lb. (2310 kg) Vehicles with 2.7 L 4-cylinder (2TR-FE) engine 5350 lb.
Page 929 Abbre via t ion list Abbreviat ion/Ac ronym list ABBREVIATIONS MEANING Two Wheel Drive Four Wheel Drive Anti-Lock Brake System Accessory Automatic Locking Retractor A-TRAC Active Traction Control AUTO LSD Automatic Limited Slip Differential Child Restraint System Downhill assist control Electronic Control Unit Event Data Recorder Emergency Locking Retractor...
Page 930 Abbreviation list ABBREVIATIONS MEANING Tire Identification Number TPMS Tire Pressure Warning System TRAC Traction Control Treadwear indicators Trailer Weight Rating Vehicle Identification Number Vehicle Stability Control...
Page 931 Alpha be t ic a l inde x Alpha be t ic a l index A/C..........248 Audio remote controls .... 303 ABS ...........200 Audio system Access doors ......43 Antenna....264, 418, 420 Active traction control Audio input .... 280, 288, 301 system ........190 AUX port .......
Page 932 Alphabetical index ® Bluetooth audio..... 309 Child safety ® Bluetooth phone ....326 Airbag precautions ....97 Bottle holders ....365, 369 Battery precautions ..449, 538 Brake assist ......200 Child restraint system....108 Brakes Child-protectors.......41 Brake system warning buzzer How your child should wear ...
Page 933 Alphabetical index Daytime running light Emergency, in case of system ........166 Blown fuse ......474 Deck If the engine will not start ..532 Auxiliary boxes ......392 If the shift lever cannot be Deck ........391 shifted from P ..... 533 Deck hooks ......393 If the vehicle battery is Deck rails ......212...
Page 934 Alphabetical index Engine coolant Front passenger’s seat belt Capacity ....... 559 reminder light......508 Checking ......443 Front passenger’s seat belt Preparing and checking warning buzzer ......508 before winter ...... 219 Front seats Temperature gauge....157 Adjustment ......49 Engine coolant temperature Front side marker lights gauge ........
Page 935 Alphabetical index Hands-free system Interior lights (for cellular phone) ....326 Interior lights ......364 Hazard lights Personal lights ...... 364 Switch........496 Switch ........364 Head restraints Wattage......... 568 Adjusting ........58 Instrument panel light Headlights control ........158 Replacing light bulbs .....485 Switch........164 Jack Wattage.........568...
Page 936 Alphabetical index Lights Noise from under vehicle ..27 Automatic light off system ..166 Emergency flashers switch... 496 Odometer ........158 Fog light switch..... 167 Off-road precautions Hazard light switch ....496 Driving ........209 Headlights switch ....164 Vehicle ........207 Instrument panel light control dial......
Page 937 Alphabetical index Radiator ......436, 444 Seat belts Radio .........260 Adjustment ......63 Rear seat ALR .........65 Adjustment ......54 Automatic Locking Folding down......55 Retractor.......65 Raising the bottom Child restraint system cushion .........54 installation......112 Rear side marker lights Cleaning and maintaining ..422 Replacing light bulbs ..490, 493 ELR .........65 Switch........164...
Page 938 Alphabetical index Seatback table ......388 Storage feature......365 Service reminder Storage precautions ....215 indicators ......160 Stuck Shift lever If the vehicle becomes Automatic transmission ..146 stuck ........542 If the shift lever cannot be Sun visors.........373 shifted from P..... 533 Switch Manual transmission ....
Page 939 Alphabetical index Tachometer.......157 Tools ......... 515 Tailgate Total load capacity ....217 Removing the tailgate .....44 Towing Tailgate ........44 Bumper towing ...... 233 Tail lights Dinghy towing ....... 244 Replacing light bulbs ..490, 493 Emergency towing ....497 Switch........164 Fifth wheel trailer....231 Wattage.........568 Trailer towing ......
Page 940 Alphabetical index Warning buzzers Washing and waxing ....418 Key reminder ......510 Weight Brake system......505 Cargo capacity ......212 Seat belt reminder ....508 Cargo weight rating ....605 Warning lights Gross axle weight rating..607 ABS ........506 Gross combination weight Airbag system.......
Page 941 Wha t t o do if... What t o do if... If you have a flat tire P. 515 A tire punctures P. 532 If the engine will not start The engine does not start P. 84 Engine immobilizer system P.
Page 942 What to do if... Instrument cluster ■ Center panel ■...
Page 943 What to do if... ■Warning lights Brake system warning Slip indicator* light P. 507 Cruise control indicator light* P. 505 P. 507 Automatic transmission Charging system warning fluid temperature light warning light P. 506 P. 507 Open door warning light Low engine oil pressure warning light P.
Page 944 M e m o...
Page 945 Cold tire inflation P. 564 pressure Engine oil capacity (Drain and refill P. 556 -reference) Toyota Genuine Motor Oil or equivalent Oil grade: P. 556 ILSAC multigrade engine oil Engine oil type Recommended oil viscosity: SAE 0W-20 (2.7 L 4-cylinder [2TR-FE] engine)

Toyota Display Audio system Owner's Manual

1 Before Driving

Quick Links

CONFIRMING DISPLAY AUDIO MODEL

EXISTENCE OF NAVIGATION CAPABILITIES

Related Manuals for Toyota Display Audio system

Summary of Contents for Toyota Display Audio system

Table of Contents