Related Manuals for Toyota GENUINE AUDIO AVENSIS T25
Summary of Contents for Toyota GENUINE AUDIO AVENSIS T25
- Page 1 AUDIO TOYOTA GENUINE AUDIO NOTICE EXPLICATIVE DE L’INSTALLATION Avensis FÜR-FOR-POUR ** T25 * R Binder Volume 4 Manual Ref.no A4RT25/J-0-0...
- Page 2 Avensis (T25) TOYOTA GENUINE AUDIO 1. TABLE OF CONTENTS 1. Application Chart .................................... 2. System Layout ....................................3. In-dash 6 CD-Changer Installation ..............................4. Hide-away 6 CD-changer installation .............................. Avensis (RHD) - 3 10-02...
- Page 3 p. 1/1 Audio Design Unique...
- Page 4 Avensis (T25) TOYOTA GENUINE AUDIO 2. SYSTEM LAYOUT THE HIDE-AWAY 6 CD-CHANGER NOTE: The installation position of the hide-away 6 CD-changer in under the driver seat. Avensis (RHD) - 5 10-02...
-
Page 5: In-Dash 6 Cd-Changer Installation
Avensis (T25) TOYOTA GENUINE AUDIO 3. IN-DASH 6 CD-CHANGER INSTALLATION Remove the shift knob and shift cover using a nylon pry tool. : Clip (4x) : Nail (4x) Fig. 1 Remove the panel : Clip (5x) Fig. 2 Attach the protection tape Fig. - Page 6 Avensis (T25) TOYOTA GENUINE AUDIO Remove the audio unit : Bolt (4x) Fig. 4 Remove the glove compartment Remove the hooks : Hook (2x) Remove the stoppers by pulling them inside. Fig. 5 Remove the switch Remove the bulb Remove the connector by moving it upward.
- Page 7 Avensis (T25) TOYOTA GENUINE AUDIO Cut the tape into 10 equal pieces. Fig. 7 Relocate the vehicle connector position from location “A” to location“B” and attach the connector to the har- ness using tape and a wire tie : Wire tie (1x) “A”...
- Page 8 Avensis (T25) TOYOTA GENUINE AUDIO Route and attach the changer wire using wire ties : Wire tie (3x) Wire of changer unit Connect Fig. 9 10. Route the changer wire using wire ties and wrap the connectors using tape : Tape 2x (3x)
- Page 9 Avensis (T25) TOYOTA GENUINE AUDIO 11. Cut the template (312N) (see page 22, 23) using scissors. Fig. 11 12. Mark the dashboard using the template Hole fit (312N) Corner fits Corner fits Marking Fig. 12 13. Use protection tape in order not to Drill a hole of 10mm damage the surface of the dashboard.
- Page 10 Avensis (T25) TOYOTA GENUINE AUDIO 14. Cut the marked position on the dash- board using a saw. Fig. 14 15. Cut the marked position on the dash- board using a saw. Fig. 15 16. Temporary attach the screws in the Existing holes existing holes.
- Page 11 Avensis (T25) TOYOTA GENUINE AUDIO 17. Fit the side bracket (L) and (R) onto the changer unit : Bolt (M5x8) (4x) Fig. 17 Fit the switch Fit the in-dash changer unit Connector : Screw (M6x12) (2x) : Screw (M6x14) (2x) Fig.
- Page 12 Avensis (T25) TOYOTA GENUINE AUDIO 20. Fit the glove compartment : Hook (2x) Fig. 20 21. Cut the panel Fig. 22 Avensis (RHD) - 13 10-02...
- Page 13 Avensis (T25) TOYOTA GENUINE AUDIO 22. Fit the panel Fig. 23 Avensis (RHD) - 14 10-02...
- Page 14 Avensis (T25) TOYOTA GENUINE AUDIO 3. HIDE-AWAY 6 CD-CHANGER INSTALLATION Remove the shift knob and shift cover using a nylon pry tool. : Clip (4x) : Nail (4x) Fig. 24 Remove the panel : Clip (5x) Fig. 25 Attach the protection tape Fig.
- Page 15 Avensis (T25) TOYOTA GENUINE AUDIO Remove the audio unit : Bolt (4x) Fig. 28 Remove the cover : Screw (2x) Remove the centre console : Screw (4x) : Bolt (4x) Fig. 29 Avensis (RHD) - 16 10-02...
- Page 16 Avensis (T25) TOYOTA GENUINE AUDIO Remove the front door scuff plate (R). : Nail (5x) Remove the kick panel (R). : Nut (1x) Fig. 30 Remove the driver seat : Bolt w/washer (4x) : Cover (2x) CAUTION Fasten the bolt with specified torque when reassembling.
- Page 17 Avensis (T25) TOYOTA GENUINE AUDIO Route the changer wire and wrap the connectors using tape : Tape (2x3) Vehicle Harness WITH POP UP DISPLAY Do not connect To audio AVC-LAN wire harness WITHOUT POP UP DISPLAY Do not connect To audio...
- Page 18 Avensis (T25) TOYOTA GENUINE AUDIO Route the changer wire along the cross member and attach using tape (4x). Attach the excess wire of the changer wire onto the cross member using tape (6x). Vehicle harness Excess wire Fig. 35 12. Cut the carpet at the changer unit attachment position on the driver side.
- Page 19 Avensis (T25) TOYOTA GENUINE AUDIO 13. Attach the adhesive tapes and the spacers ( ) to the base brack- using screws : Spacer (w/o nut) : Spacer (w/nut) : Tape (1x) * : Tape (cut to size 67mmx50mm) (1x) : Screw (M5x16) (2x) Fig.
- Page 20 Avensis (T25) TOYOTA GENUINE AUDIO 15. Mount the side brackets (2x) to the changer unit : Bolt (M5x8) (4x) CAUTION CAUTION Loosen the screws before moving Screw them. Tighten up after the position is changed. Hole position on the left side Hole position on the right side Fig.
- Page 21 Avensis (T25) Cut line precisely Cut a long hole Cut line Avensis (RHD) - 22 10-02...
- Page 22 TOYOTA GENUINE AUDIO 312N TEMPLATE precisely Cut line Avensis (RHD) - 23 10-02...
- Page 23 TOYOTA MOTOR CORPORATION...