Changing The Fuses; Beam Setting; Bulbs - MOTO GUZZI Norge 1200 Use & Maintenance Book

2
3
4
u Clean the switch if caked with dirt or

CHANGING THE FUSES

mud. The pin must move freely and
C a r e f u l l y
return automatically to its initial position.
(MAINTENANCE).
Make sure that the cables are connected
u
correctly.
Do not repair faulty fuses.
Never use a fuse of a rating other than
specified.
This could damage the electric system
or cause a short circuit, with the risk of
fire.
NOTE
If a fuse blows repeatedly, there
might be a short circuit or an overload in
the electric system.
4
3
Check as follows: NOTE
When you use one of the spare
fuses, remember to add a new spare fuse
u Set the ignition switch to " " to avoid
an accidental short circuit. into the proper seat.
u Remove the rider seat, see page 31
u Repeat the above operations for the
(UNLOCKING/LOCKING THE SEAT).
main fuses.
u Open the auxiliary fuses (2) carrier (1)
NOTE
Removing the 30A fuses resets
cover.
the following functions: digital clock, trip
u Extract and check the fuses one by one -
info and lap times.
a divided link bar (5) means that the fuse
is blown.
To re-set these functions, see page 18
u Before replacing a fuse, identify the
(MULTIFUNCTION LCD DISPLAY).
cause of the failure if possible.
u Replace the blown fuse with a new one
with equal current rating.
86
use and maintenance Norge 1200
1
In this case it is advisable to contact a
Moto Guzzi Authorised Dealer.
r e a d p a g e 6 2
Checking the fuses is recommended
whenever an electric component fails to
operate or is malfunctioning, or when the
CAUTION
engine does not start.
First check auxiliary fuses (2), ABS fuses
(3) and then main fuses (4).
use and maintenance Norge 1200
5
f e d c b a
ARRANGEMENT OF AUXILIARY FUSES
a) Stop, horn, HAZARD button light, light
relay coil (15A).
b) Parking lights, starter relay coil, passing
(15A).
c) Fuel pump, coils, injectors (20A).
d) Lambda burner, secondary injection
relay coil, starter relay coil, speed
sensor power (15A).
e) Permanent positive, ECU power (3A).
f) ABS (10A) .
NOTE
There are three spare fuses (3,
15, 20 A).
i
4
g
h
LAYOUT OF THE ABS FUSES
g) ABS (40A) .
h) ABS (25A) .
85
2
1
BEAM VERTICAL ADJUSTMENT
u Place the vehicle upright.
Move aside the dash panel, see page
u
48 (LIFTING THE DASH PANEL).
Adjust headlight beam, turn screw (1).
u
When finished:
WARNING
Check beam correct horizontal setting
and install the dash panel.
88
use and maintenance Norge 1200
i
l
l
ARRANGEMENT OF MAIN FUSES

BEAM SETTING

i) From battery to voltage regulator (30A). NOTE
j) From battery to key and C and D fuses
vary from country to country. Observe the
(30A).
law in force in the country of the user.
NOTE
There is one spare fuse.
For a quick beam inspection, place the
vehicle on level ground, ten metres away
from a vertical wall.
Switch on the low beam, sit astride the
vehicle and make sure that the light spot
on the wall is just below the horizontal line
of the headlight (about nine/tenths of
overall height).
BEAM HORIZONTAL ADJUSTMENT
u Place the vehicle on the stand, see page
60 (PUTTING THE VEHICLE ON THE
STAND).
u Move aside the dash panel, see page
48 (LIFTING THE DASH PANEL).
u Turn screw (2) to adjust the beam
direction.
When finished:
WARNING
Check beam correct vertical setting and
install the dash panel.

BULBS

C a r e f u l l y
(MAINTENANCE).
Fire hazard.
K e e p f u e l a n d o t h e r f l a m m a b l e
s u b s t a n c e s a w a y f r o m e l e c t r i c
components.
Beam inspection procedures may
use and maintenance Norge 1200 87
r e a d p a g e 6 2
WARNING