System Menu - ADJ X-move LED plus User Instructions

SYSTEM MENU

System Menu: When making adjustments you can press ENTER to confirm your setup or you can wait
8 seconds for automatic setup. To exit without making any adjustments press the MENU button.
ADDR
- DMX Address Setting.
1. Tap the either the MENU, UP, or DOWN buttons until "ADDR" is displayed, press ENTER.
2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired
address. Press ENTER to set your desired DMX address.
SHND
- This will let you choose one of the four preprogrammed shows. See show descriptions
below.
1. Tap the either the MENU button until "SHND" is displayed, press ENTER. Either "SH 1", "SH 2", "SH 3" or
"SH 4" will be displayed.
2. Tap the UP or DOWN buttons to find you desired show and then press ENTER to confirm and exit.
SHOWS:
Show 1 - For fixtures placed on the floor, the tilt movement angle is 210°
Show 2 - For fixtures fixed to the ceiling or truss, the tilt movement angle is 90° .
Show 3 - For fixtures placed on a table or stage. The beam is projected at the audience's direction; i.e. in front
of the stage. Pan movement angle (left to right to left) is 160° . Tilt movement angle is 90° .
Show 4 - For fixtures fixed to the ceiling. The beam is projected at the audience's direction; i.e. in front of the
stage. Pan movement angle (left to right to left) is 160° . Tilt movement angle is 90° .
SLND
- This will let you set unit as a master or slave in a master/slave configuration.
1. Tap the MENU button until "SLND" is displayed, press ENTER. Either "SL 1" or "SL 2" will be displayed.
2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to confirm.
Note: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to "SL 2",
the fixtures will now have contrast movement to each other.
SOUN
- Sound Active mode.
1. Tap the MENU button until "SOUN" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select "ON" to activate sound
active mode, or "OFF" to deactivate sound active mode.
3. Press ENTER to confirm.
BLND
- Blackout or Stand by mode.
1. Tap the MENU button until "BLND" is displayed, press ENTER. Either Yes or No will be displayed.
2. To activate Blackout tap the UP or DOWN buttons until "Yes" is displayed, press ENTER to confirm. The
fixture will now be in Blackout mode. To deactivate Blackout mode, select "No" and press Enter.
I PAN
- Pan Inversion
1. Tap the MENU button until "I PAN" is displayed, press ENTER. Either NO or 1 will be displayed.
2. To activate the Pan inversion tap the UP or DOWN buttons until I is displayed, press ENTER to
confirm. To deactivate Pan inversion, select No and press Enter.
I TLT
- Tilt Inversion
1. Tap the MENU button until "I TLT" is displayed, press ENTER. Either NO or 1 will be displayed.
2. To activate the Tilt inversion tap the UP or DOWN buttons until I is displayed, press ENTER to confirm. To
deactivate Tilt inversion, select No and press Enter.
LED
- With this function you can have the LED display turn off after 10 seconds.
1. Tap the MENU button until "LED" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select "ON" to keep the LED
display on at all times, or "OFF" to switch to have the LED display switch off after 10 seconds.
3. Press ENTER to confirm.
DISP
- This function will reverse the display 180º.
A.D.J. Supply Europe B.V. – www.americandj.eu – X-Move LED Plus™ Instruction Manual Page 8