Table of Contents
Advertisement
Quick Links
CAUTION
READ THESE INSTRUCTIONS BEFORE USING THIS MACHINE
TORNADO INDUSTRIES, LLC
333 CHARLES COURT
WEST CHICAGO, IL 60185
(630)-818-1300 FAX (630)-818-1301
WWW.TORNADOVAC.COM
Operations & Maintenance Manual
For Commercial Use Only
BD 26/27 RIDE ON SCRUBBER
MODEL NO: 99770
Form No. L3456A
©Tornado INDUSTRIES, LLC. All rights reserved
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tornado BD 26
Summary of Contents for Tornado BD 26
- Page 1 READ THESE INSTRUCTIONS BEFORE USING THIS MACHINE TORNADO INDUSTRIES, LLC 333 CHARLES COURT WEST CHICAGO, IL 60185 (630)-818-1300 FAX (630)-818-1301 WWW.TORNADOVAC.COM Operations & Maintenance Manual For Commercial Use Only BD 26/27 RIDE ON SCRUBBER MODEL NO: 99770 Form No. L3456A ©Tornado INDUSTRIES, LLC. All rights reserved...
-
Page 2: Table Of Contents
Working in manual mode SUMMARY Working adjustments LEGEND PANEL OF CONTROLS Flow adjustment of the detergent solution LEGEND MACHINE Brush pressure adjustment TECHNICAL DESCRIPTION Electric protection INTRODUCTION Overflow device GENERAL RULES OF SECURITY STOPPING THE MACHINE AFTER CLEANING SYMBOLS DAILY MAINTENANCE BEFORE USE Emptying and cleaning the recovery tank Handling packed machine... -
Page 3: Legend Panel Of Controls
LEGEND PANEL OF CONTROLS 1. Display 15. Signal Lamp For Parking Brake On 2. Signal Lamp Manual Mode On 16. Signal Lamp Brushes Raise/Lower 3. Push Button For Manual Mode 17. Push Button Raise/Lower Brushes 4. Signal Lamp Mode Break Washing On 18. -
Page 4: Technical Description
TECHNICAL DESCRIPTION BD26/27 Cleaning width Squeegee width 38.5 Working capacity, up to sqm/h 35,521 Brush diameter 2 x 13.5 Brush speed Brush pressure Brush motor 650 (27 A) Traction motor 500 (25 A) Vacuum motor 580 (24 A) Suction vacuum Water lift Type of drive Auto... -
Page 5: Introduction
INTRODUCTION - Do not strike shelving or scaffoldings, Indicates the solution valve that adjusts the flow of Thank you for choosing our machine. where there is danger of falling solution detergent. This floor cleaning machine is used objects. for industrial and commercial cleaning - Adapt the machine speed to the and is able to clean any type of floor. -
Page 6: Before Use
Indicates the direction of operation: forwards/backwards. Indicates the brake. Light indicates the brake is on. Indicates the parking brake. BATTERY INSTALLATION 4. Keep the pallet and the brackets for future transport. The machine is equipped batteries connected in series for a total of 24 ACCESS TO THE BATTERY Indicates the operator has Volts, placed in its appropriate... -
Page 7: Battery Charging
1. Disconnect the connector of the BATTERY CHARGING battery charger from the battery 1. Plug the battery connector (3) of connector (1). the battery charger into the battery 2. Reconnect the battery connector to connector (1). the machine connector (2). 2. -
Page 8: Hour Meter
4. The writing GE24 appears flashing. Both wheels must be adjusted to the 5. When the writing stops flashing, the same height. setting is modified. To change the setting from gel batteries to lead batteries, repeat the procedure pressing button (3) instead of button (6). -
Page 9: Assembling The Brushes
inclination of the bristles causes excessive motor overload or troublesome vibrations. ATTENTION: ASSEMBLING THE BRUSHES Use only brushes supplied with the ATTENTION: machine or ones indicated in the To assemble the brushes it is Always use a low foaming detergent. paragraph RECOMMENDED necessary that the brushes base is in To avoid foaming, before starting the... -
Page 10: Forward And Backward Movement
II. to separately activate only the that the fast drive is selected, while controls relative to the washing signal lamp (23) indicates that the function with the brushes (see under slow drive is selected. paragraph WORKING IN MANUAL 9. When moving in reverse, an MODE ). -
Page 11: Working In Manual Mode
solenoid valve opens to permit the TO CARRY OUT THE WASHING detergent solution to flow down onto WITH ONLY THE BRUSHES: the brushes and the vacuum system 1. Check that the knob of the solution is activated to recover the dirty water valve (27) is in the position of from the floor. -
Page 12: Electric Protection
ATTENTION: functions have to be re-established In order not to overload the brush manually. motor, reduce the brush pressure going from smooth floors to rough ones (ex. concrete). STOPPING THE MACHINE AFTER CLEANING IN AUTOMATIC OR MANUAL DAILY MAINTENANCE WORKING MODE: 1. -
Page 13: Cleaning The Vacuum Filter
3. Turn the rubber to a new side or replace it. To reassemble the squeegee repeat inversely the operations mentioned above, inserting the rubber on the guides and blocking it with the rubber holder blade. CLEANING THE SQUEEGEE CLEANING THE VACUUM FILTER Keeping the squeegee clean 1. -
Page 14: Two-Monthly Maintenance
6. Reassemble all parts. Pour some water into the tank to clean it. Reassemble the fitting onto NOTE: if required it is possible to the solution tank. wash only the components of the outer solution filter by closing the solution valve adjustment (see under paragraph FLOW ADJUSTMENT OF THE DETERGENT SOLUTION ), so that the detergent solution remains in... -
Page 15: The Water Does Not Come Down Onto The Brushes Or Is Insufficient
4. Check that the parking brake signal 5. Clean the vacuum filter (see under lamp (15) is not on and release it if paragraph CLEANING THE necessary (see under paragraph VACUUM MOTOR ). EMERGENCY-PARKING BRAKE ). 6. Clean the squeegee hose (see 5. -
Page 16: Programmed Maintenance
PROGRAMMED MAINTENANCE 1000 HOURS IINTERVAL DAILY 20 HOURS * 200 HOURS * · RECOVERY TANK CLEANING · VACUUM FILTER CLEANING · SOLUTION TANK FILTER CLEANING · BRUSH CLEANING · BRUSH DISASSEMBLY AND CLEANING · SQUEEGEE CLEANING · FRONT SQUEEGEE BLADE REPLACEMENT ·...
Need help?
Do you have a question about the BD 26 and is the answer not in the manual?
Questions and answers