Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Belling GHU60-70 AU
Summary of Contents for Belling GHU60-70 AU
- Page 1 Users Guide & Installation Handbook Belling Built in Gas Hobs GHU60-70 AU...
- Page 2 our warranty Should you need it ..Inside the paperwork which has come with this appliance, there is a leaflet and card explaining the terms of our extended warranty and guarantee. In order to apply for our five year guarantee, simply fill in the details on the card and post it off, this will register your appliance.
-
Page 3: Table Of Contents
Contents Introduction ..........Safety and Ignition . -
Page 4: Introduction
To fulfil the conditions of your guaran- Thank you fo r buyi ng thi s Brit ish built tee, this appliance must be correctly appliance from Belling, this look is installed and operated, in accordance intended to assist you with the... - Page 5 Be safe - not sorry Caution: This appliance is for cooking purposes only. It must not be used for other purposes, for example room heating Auto ignition (if fitted):Push in and hold down the controlknob, and turn to the full WARNING! -Accesible parts may become on position(large fl ame s ymbol).
- Page 6 Do not use griddle plates on this Using the hob appliance, as this may be haz- Adjust the burner flame so that it does ardous. not extend over the pan base. Material and size of pan, as well as quantity and type of food to be cooked, can affect cooking times.
-
Page 7: Pan Supports
Pan supports Note Always make sure the pan supports Extra care should be taken when cook- are replaced correctly , located in the ing food in salted water. Some foods hob spil lage w ell, and that all ru bber are corrosive - eg;... -
Page 8: Care And Cleaning
Any brownish coloured marks o n the Care & Cleaning burners are carbon deposits or fat stains, Caution: Any cleaning agent which can be r emoved by gently rub- used incorrectly may damage bing with a soapy pad. the hob. The berner Important: caps and... -
Page 9: Control Knobs
Sharp objects can mark the surface of Control knobs stainless s teel, b ut m arks wi ll b ecome use hot soapy water. Only less noticeable with time. When cleaning the f ascia are a, ca re To maintain the finish of stainless steel, must be taken on symbols / markings. - Page 10 InstallatIon InstructIons - gas products Before you start: Please read the Ventilation requirements instructions. Planning your installation will Ventilation must be as specified by save you time and effort. AS 5601 Installation code. The room Prior to installation, ensure that the local conatining the appliance should have an distribution conditions (nature of the gas air supply.
-
Page 11: Installation
Installation Failure to comply with these This appliance must be installed in Regulations is a criminal accordance with the regulations in offence. force, and only i n a well ventilated Where reg ulations or standards h ave space. Read the instructions before been revised since this handbook was using or installing this appliance. -
Page 12: Clearance And Dimensions
Clearances & dimensions We recommend ceramic tiling for the rear wall directly behind the hob. The room should have good light and ventilation but be free from draughts. No shelf or overhang of combustible material should be closer than 650mm The worktop should be at least above the hob. -
Page 13: Important Information
Important Information Failure to follow these instructions can It is important when installing front lead to exessive force being applied control gas hobs, that the work top to the basetray, which results in the cut out is the same as is quoted in clearence between the control knob this installation manual. - Page 14 Fit the hob into the cutout & secure to worktop Place the hob into the cutout and secure in place using the four brackets and screws provided. The brackets should be orientated to suit the worktop thickness as shown, then inserted into the four slots (two on the front edge and two on the rear) and screwed into the underside of the worktop using the woodscrews provid-...
- Page 15 lternative clamp positions If the front and rear clamp positions are problematic, alternative positions can be used o n the s ides of the hob, dependant on the particular installa- tion. These positions will r equire clearance from any cabinet sides and may effect how tightly the hob will meet the work- top.
- Page 16 Installation advice - cabinetry Any modifications must ensure that Dealing with sides, cross- rails the strength of the cabinet is main- and back-panels in cabinetry tained. Depending on the cabinets, the wor k- Back-panel top thickness and the hob positioning, Interference with clamp brackets it is possible for the hob base, the clamp brackets and/or the gas con -...
- Page 17 adjacent heat source, such as an oven grill or hob. Ensure that all pipe work is of the InstallatIon InstructIons - gas products correct rating for both size and temperature. Means of isolation shall be provided connect to the gas supply at the shut off point by either an Means of isolation shall be provided at the after installation, make sure all connections...
-
Page 18: Troubleshooting
Troubleshooting Before you call Customer Care, please check the following points: Burner fails to ignite: • Check the electricity supply is on. • Check the fuse. There is a spark t o t he bu rner but it fails to ignite: Check that the flame ho les i n the •... - Page 19 Technical Data This in formation is Natural gas @ 1.0kPa for the following appliances: Propane gas @ 2.75kPa Belling Hobs GHU60/70 front & side control - NG & LPG Countries of destination (AUS & NZ) Data badge Underside of the hob...
- Page 20 Glen Dimplex Australia, Unit 2, 205 Abbotts Road, Dandenong South, Victoria 3175 Australia Glen Dimplex Australia, Unit 2, 205 Abbotts Road, Dandenong, e-mail: sales@glendimplex.com.au web: www.glendimplex.com.au South Victoria 3175, Australia e-mail: sales@glendimplex.com.au Model Names: web: www.glendimplex.com.au Model names: Belling GHU 60 - 70 GAS HOB 08 27521 00a 05.2010...