Advertisement
Advertisement
Table of Contents
Related Manuals for Belling GTG 60 LPG Series
Summary of Contents for Belling GTG 60 LPG Series
- Page 1 Belling GTG / GHU 60 & 75 LPG Date: 17/04/20...
- Page 2 PL - Poland NZ - New Zealand AU - Australia ES - Spain NL - Netherlands To contact Belling about your appliance, please call: Warranty Registration Customer Care Helpline 0344 815 3746 0800 952 1068 In case of difficulty within the UK...
- Page 3 INTRODUCTION This user guide book is designed to help you through each step of owning your new product. Please read it carefully before you start using your appliance, as we have endeavored to answer as many questions as possible, and provide you with as much support as we can. General information, spares and service information is available from our website.
- Page 4 SAFETY WARNING • Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Page 5 • Do not modify this appliance. • Do not place articles on or against the appliance. • Servicing should be carried out only by authorised personnel. • Always switch off your appliance and allow it to cool down before you clean any part of it. •...
- Page 6 If you have an electrical fire in the kitchen and consider it is safe to do so: • Pull the plug out, or switch off the power at the fuse box - this may be enough to stop the fire immediately.
-
Page 7: Using Your Appliance
USING YOUR APPLIANCE Getting to know your product Note: Your appliance layout may differ depending on the model. BEL GTG600C LPG Blk BEL GTG75C LPG Blk Rapid Semi Rapid Semi Auxiliary Semi Auxiliary Semi BEL GHU602C LPG Sta BEL GHU75C LPG Sta Semi Rapid Semi - Rapid... - Page 8 Control panel GTG600C / GHU602C Cook zones Control panel GTG75C Cook zones Control panel GHU75C Cook zones...
- Page 9 The following symbols will appear on the control knob, next to each other: Ignition position • The minimum setting is at the end of the anti-clockwise rotation of the control handle. • All operation positions must be selected between the maximum and minimum position. •...
- Page 10 Pan sizes required Pans Burners min. max. 200mm 260mm Rapid 180mm 220mm Semi-Rapid 180mm 200mm Auxiliary 120mm 180mm Warning: Do not allow cooking vessels to overlap cooking zones. Not adhering to the maximum recommended pan sizes may result in the control knobs becoming excessively hot during use and they may become heat damaged over time.
-
Page 11: Troubleshooting
Trouble shooting • Repairs should be performed by a licensed technician only. Improper repair may result in considerable danger to you and others. • However, some minor problems can be resolved as follows: Problem Probable cause Solution No Spark. Check the electricity supply. The burner caps and skirts are not No ignition Assemble them correctly. -
Page 12: Cleaning Your Appliance
CLEANING YOUR APPLIANCE Note: Always switch off your appliance and allow it to cool down before you clean any part of it. Note: Please take extra care when cleaning over the symbols on the control panel, as this can lead to them fading. -
Page 13: Gas Installation
Gas Installation • It is the law that all gas appliances are installed by competent persons in accordance with the current edition of the Gas Safety Installation and Use Regulations. • It is in your interest and that of safety to ensure compliance with the law. •... - Page 14 The room containing the appliance should have an air supply in accordance with BS5440: Part 2 • All rooms require an openable window, or equivalent, and some rooms will require a permanent vent as well. • For room volumes up to 5m an air vent of 100cm is required.
-
Page 15: Installing The Appliance
Installing the appliance This appliance is to be built into a worktop 600mm deep providing the following minimum dis- tances are maintained; • The edges of the hob must be a minimum distance of 50mm from rear wall and 200mm from side wall and this area should be free of any combustible materials. - Page 16 With Steel hob To prevent leakage of liquid between the frame of the hob and the worktop, put the insulating seal provided in position before assembly. 1. Install the product into the worktop cut-out and use a pencil to draw a line along the product outer edges. 2.
- Page 17 Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the appliance from the aperture in future, particularly if it needs to be serviced. (A) SEALING STRIP (C) SCREW (B) BRACKET 2.
-
Page 18: Gas Connection
Gas Connection • This appliance must be installed and connected in accordance with installation regulations in force in the country in which the appliance is to be used. • This appliance is supplied to run on LPG and natural gas. Conversion for use on LPG and natural gases must only be undertaken by a qualified person. -
Page 20: Technical Data
TECHNICAL DATA Gas hob Burner Rapid Semi-Rapid Auxiliary Category Gas Type Rated Power 1.75 (kW) Rated Flow (g/h) G30/G31 28-30/37 mbar Injector 0.96 0.87 0.66 0.50 Diameter(mm) Natural Gas Injector I2H/I2E/I2E+ 1.44 1.30 1.00 0.78 20 mbar Diameter(mm) G30/G31 Injector 0.96 0.87 0.66...