Installing Software; Required Computer Environment; Installing Software (Including Printer, Scanner And Other Drivers) - Panasonic KX-MB2100 series Operating Instructions Manual

2. Installation and Preparation
1
Mt/MENUN A MBNM5NM8NM3N A MOK/SETN
R The PIN code of the unit is displayed.
2
Register the PIN code to your wireless access point.
3
MOK/SETN
R Perform step 3 within 1 minute of performing step
2.
R "CONNECTING....." blinks while connecting.
When the connection is complete,
"CONNECTED" will be displayed.
R If the unit enters standby mode during the
process, repeat from step 1 (the PIN code will be
renewed).
2.7.3 WPS incompatible access point
Important:
R Make sure the LAN mode setting is set to
"WIRELESS" beforehand (feature #580).
R The following setting information for your
wireless access point is required:
– Network name (SSID)
– Network key (WEP / WPA key)
– Connection type
– Network authentication type
– Data encryption type
*1 If your wireless access point is equipped with
several network keys, use only the first
network key (this unit is equipped with a
single network key).
R If your wireless access point is configured to not
show the network name (SSID), enter the network
name (SSID) manually (feature #585).
1
Mt/MENUN A MBNM5NM8NM4N A MOK/SETN
2
MCDN: Display the desired network name (SSID).
A MOK/SETN
R Depending on the settings for your wireless
access point, it may be necessary to select
WEP64 or WEP128. Select the desired item, and
then press MOK/SETN.
3
Enter the network key. A MOK/SETN
R Depending on the settings for your wireless
access point, this step can be omitted if
encryption is not used.
R "CONNECTING....." blinks while connecting.
When the connection is complete,
"CONNECTED" will be displayed.
Setting up your wireless access point manually
1. Mt/MENUN A MBNM5NM8NM5N A MOK/SETN
2. Enter the network name (SSID). A MOK/SETN
3. MCDN: Display the desired connection type. A MOK/
SETN
4. MCDN: Display the desired network authentication
type. A MOK/SETN
22
5. MCDN: Display the desired data encryption type. A
6. Enter the network key. A MOK/SETN
2.7.4 Setting up using Windows
If you use a Windows computer, it is possible to configure
wireless LAN settings during the installation of
Multi-Function Station. For details, see "2.9 Installing
software (including printer, scanner and other drivers)"
(page 22).
2.8 Required computer
environment
*1 Important:
R When using Windows Server
R With Mac OS X, only the printer driver, scanner
To use Multi-Function Station on your computer, the
following are required:
Operating System:
Windows XP/Windows Vista/Windows 7/Windows 8
CPU:
Complies with Operating System recommendations
RAM:
Complies with Operating System recommendations
Other Hardware:
CD-ROM drive
Hard disk drive with at least 600 MB of available space
Web browser (recommendation):
Windows Internet Explorer
Windows Internet Explorer 10/11 (with compatible mode
recommended)
2.9 Installing software (including
printer, scanner and other
drivers)
Panasonic Multi-Function Station software enables the
unit to carry out the following functions:
– Printing on plain paper, thin and thick paper, labels
MOK/SETN
R Depending on the settings for your wireless
access point, this step can be omitted if
encryption is not used.
R "CONNECTING....." blinks while connecting.
When the connection is complete,
"CONNECTED" will be displayed.
Server 2012, only the printer driver can be
supported. Install the printer driver using the Add
Printer feature of Windows.
driver (TWAIN/ICA) and PC fax (transmission) are
supported. See the setup guide for Mac OS X for
details.
®
and envelope
®
Installer
®
2008/Windows
8/9