Sime superior 40 Ci Installation And Service Instructions Manual
  1. Manuals
  2. Brands
  3. Sime Manuals
  4. Boiler
  5. superior 40 Ci
  6. Installation and service instructions manual
Sime superior 40 Ci Installation And Service Instructions Manual

Sime superior 40 Ci Installation And Service Instructions Manual

Hide thumbs

Advertisement

Table of Contents

PLEASE LEAVE THIS INSTRUCTION
WITH THE USER
GB
Superior Ci
Installation & Servicing
Instructions
Supplied By www.heating spares.co Tel. 0161 620 6677

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the superior 40 Ci and is the answer not in the manual?

Questions and answers

Related Manuals for Sime superior 40 Ci

Summary of Contents for Sime superior 40 Ci

  • Page 1 PLEASE LEAVE THIS INSTRUCTION WITH THE USER Superior Ci Installation & Servicing Instructions Supplied By www.heating spares.co Tel. 0161 620 6677...

  • Page 2: Table Of Contents

    EXPLODED VIEWS ................20 Superior 40 Ci:...

  • Page 3: Technical Features And Dimensions

    TECHNICAL FEATURES AND DIMENSIONS 1. 1 INTRODUCTION flue length of 3 m [118 in]. The combined flue and air duct can exit the boiler from either The Sime “SUPERIOR Ci” is a range of wall mounted cast iron side or from the rear of the appliance. boilers.
  • Page 4 GENERAL DATA TABLE 3a - Nominal boiler ratings (2 minutes after lighting) for Superior 40 Ci MODE OUTPUT INPUT (N.C.V.) INPUT (G.C.V.) BURNER PRESSURE Btu/h Btu/h mbar inwg CENTRAL HEATING RANGE 30,000 10.0 11. 1 37,800 9. 1 31,000 10.3 11.4...
  • Page 5 TABLE 4 - General specifications 40 Ci 50 Ci 60 Ci 80 Ci Burner Injector ø mm 3.25 3.25 3.55 4. 1 0 Max. gas consumpt. 1,38 1,69 2,05 2,75 System Press 0. 1 2 0. 1 2 0. 1 2 0.

  • Page 6: General Requirements For Installation

    GENERAL REQUIREMENTS FOR INSTALLATION 2. 1 STATUTORY REQUIREMENTS – A compartment used to enclose the appliance MUST be designed and constructed specifically for this purpose. An GAS SAFETY [INSTALLATION AND USE REGULATIONS [as existing cupboard, or compartment, may be used provided amended].
  • Page 7 VENTILATION REQUIREMENTS The domestic hot water cylinder must be of the indirect type with a separate feed and vent pipes. Single feed cylinders Detailed recommendations for air supply are given in must not be used. B55440: 2. The pump, including isolation valves, should be fitted in the The following notes are for general guidance: heating flow pipe from the appliance.
  • Page 8 ALTERNATIVE METHODS OF FILLING A SEALED SYSTEM Fig. 4 priate to one of these methods. The system pressure must a range of 0 to 5 bar, or similar, is suitable. not be less than the static head of the system. A suitable expansion vessel must be fitted to the system.
  • Page 9 TYPICAL SYSTEM DESIGN, FULLY PUMPED, OPEN VENTED. Fig. 6 2.8.6 Combined pumped C.H. & Gravity D.H.W. systems ter and be connected to each of the 22 mm connections on the flow and return manifolds. A gravity system requires a When this option of system is chosen: minimum circulating head of 1 m assuming there is no hori- The gravity hot water pipes to the indirect hot water cylinder zontal pipe run.

  • Page 10: Installing The Boiler

    INSTALLING THE BOILER Appliance package: – Boiler (appliance + mounting frame) – Installation, servicing and User instructions – Wall template MOUNTING – Fixing screws with wall plugs and washers BRACKET – 2x28 mm olives part no. 6100204 – 2x22 mm olives part no. 6100203 3.
  • Page 11 Horizontal coaxial duct lenght (Z fig. 10-13) from 380 to 580 mm from 580 to 1500 mm from 1500 to 3000 mm Standard diaphragm Optional diaphragm Diaphragm Superior 40 Ci Ø 79 Ø 84 (Code 6028622) Superior 50 Ci Ø 81 Ø...
  • Page 12 – Remove the six fixing screws securing the sealed chamber GAS CONNECTIONS front panel then remove the panel. – Place the gasket (G) under the flange of the elbow and fit The gas service cock is located at the bottom right hand side the elbow onto the top of the appliance, taking care to of the appliance.
  • Page 13 Fully pumped or combined pumped and gravity operation installed within a combined pumped and gravity system, the The appliance is supplied ready for installation within a fully switch on the rear of the control box should be set to gravity pumped heating/hot water system.
  • Page 14 FULLY PUMPED SYSTEM USING TWO ZONE VALVES Fig. 18 FULLY PUMPED SYSTEM USING MID POSITION ZONE VALVE Fig. 19 Supplied By www.heating spares.co Tel. 0161 620 6677...

  • Page 15: Commissioning And Testing

    COMMISSIONING AND TESTING SIME SUPPORT THE BENCHMARK INITIATIVE to maximum and a final check completed. – Turn off the system and drain for the final time. All relevant sections of the logbook must be filled in at the – Refill and vent the system completely.

  • Page 16: Routine Servicing Instructions

    ROUTINE SERVICING INSTRUCTIONS To ensure continued efficient operation of the appliance, it is – Unscrew the 2 screws securing the combustion chamber recommended that it is checked and serviced as necessary front panel and remove the panel, taking care not to dama- at regular intervals.

  • Page 17: Fault Finding

    FAULT FINDING When any service or replacement of electrical components necting and checking each component] is required to trace which has required the breaking and re-making of electrical the faulty component. connections has taken place, the following tests must be repeated: It is possible that a fault could occur as a result of local bur- –...
  • Page 18 FAULT FINDING 3) Turn ON external gas and electricity supplies. 4) Ensure there is 230 V at the permanent live “PHASE” on Before proceeding through this fault finding guide: the installation terminal block. 1) ensure all connections to the electronic circuit board 5) Ensure there is 230 V at the switched live “HEAT and the 12 way connector to the ignition device are cor- DEMAND”...

  • Page 19: Internal Wiring Diagrams

    WIRING DIAGRAM AND INTERNAL VIEW 7. 1 FUNCTIONAL FLOW WIRING DIAGRAM Fig. 23 Supplied By www.heating spares.co Tel. 0161 620 6677...

  • Page 20: Replacement Of Parts

    REPLACEMENT OF PARTS Before commencing any service operation, ISOLATE the CONTROL TEMPERATURE SENSOR mains electrical supply, and TURN OFF the gas supply at the main service cock. It is the law that any service work must be – Remove the casing by unscrewing the retaining screws at carried out by registered person [C.O.R.G.I.].
  • Page 21 box, taking note of their respective position. screws at bottom rear of the appliance and pulling the – Slide the burner forwards and at the same time feed the panel forwards, lifting it off the two pins at the top two two wires through the grommet in the sealed chamber.

  • Page 22: Exploded Views

    EXPLODED VIEWS 9. 1 COMBUSTION CIRCUIT 40 41 19 13 Fig. 26 Position Code Description Model Position Code Description Model 6266050 Sealed chamber rear panel 40-50-60 6229101 Smoke pressure switch bracket 6266052 Sealed chamber rear panel • 6225713 Air pressure switch 40-50 •...
  • Page 23 HYDRAULIC CIRCUIT 31 24 78 79 Fig. 26/a Position Code Description Model Position Code Description Model 6286102 Cast iron exchanger 6291400 Manifold flange 40-50-60 6291300 Flow manifold 40-50-60 68 A 6291401 Manifold flange 21 A 6291301 Flow manifold 6289723 Lower inlet pipe 6291320 Return manifold 40-50-60 6289722 Upper inlet pipe...
  • Page 24 Sime Ltd Unit D2 Enterprise Way, Bradford Road, Bradford, West Yorkshire, BD10 8EW Tel. 0870 9911114 - Fax 0870 9911115 www.sime.ltd.uk - e-mail: enquiries@sime.ltd.uk Supplied By www.heating spares.co Tel. 0161 620 6677...

This manual is also suitable for:

Superior 60 ciSuperior 50 ciSuperior 80 ci

Table of Contents