Yunca Gas LEEDZ Installation & Operation Manual page 9

LEEDZ INFRA-RED REMOTE CONTROL with AUTO TIMER.
POWER ON/OFF:
First check that two fresh AAA batteries are inserted. If the remote appears faulty,
please try replacing the batteries. At first the remote may appear to be on, but it is likely that is not so.
To turn on the remote control (it is protected with a "kiddy lock"), press and hold the POWER button for
about 2 seconds until "off" disappears from the screen, then release to unlock the safety feature. One
short press of the POWER button will turn on power to the remote control, and also start the fire on the
MANUAL - HIGH setting. Current mode / settings will be displayed. The fire will always start in manual
operating mode on a high setting. (Also refer to the next page for further information). There is an audible
beep when the fire receives a signal from the remote, range is approximately 5 metres.
CLOCK SETTING: Press the CLOCK button once ("clock" in the display
will start flashing). Press
WEEK to set the week day, press HOUR to set the hour, taking care to check if on a.m. or p.m. Press
MIN to set the minute (holding the button down will advance the minutes quicker). Press CLOCK to save
the setting.
MANUAL "FLAME" OPERATING MODE h
as three settings: High, Medium and Low. Heat output is
fixed to the setting and needs to be adjusted manually by pressing the TEMP " – " and " + " buttons.
"FUZZY LOGIC" OPERATING MODE r
eplaces the traditional thermostat operation with six "comfort
levels". Press MODE to switch between Manual and Fuzzy Logic, and use the TEMP " – " and " + "
buttons. Choose the comfort level that best suits your needs. Every now and then the fire will give a short
boost of heat and then return to your chosen setting. This is the most economical way to operate your
Yunca Fuzzy Logic control fire.
HINT: The two speed fan is designed to quickly transfer heat around the room and ensures the most
economic gas use. The three-position switch (HIGH / OFF / LOW) is located on the right side plinth.
AUTO FUNCTION:
To set this feature you will need to ensure the remote control is on (as advised
above), and ensure the CLOCK time and day are correctly set. PLEASE NOTE: If a key is not pressed for
7 seconds, the programming will "time out" and you will need to re-start the process.
Set times to Start and/or Stop the fire with a choice of up to two daily programme settings (PROG1 and
PROG2). You can choose to use only PROG1 if only one setting is needed. Heat output on Auto is
initially run in manual control, and once the fire is operating you can then switch to the more economical
Fuzzy Logic.
EXAMPLE: Set PROG1 to start at 6:00 am, stop at 8.00am. Set PROG2 to start at 4.30pm, stop at
10.30pm Monday to Friday. Both PROG1 and PROG2 may have different settings programmed for the
weekend if required.
TO SET: Press PROG1 to set the "timer on" setting (Mon-Fri). Now choose the desired heat output (High,
Med or Low) Press HOUR button, making sure you have chosen the correct a.m. or p.m. time, then press
MIN button (increases in 10 minute steps) to set the start time. Press PROG1 again and use the HOUR /
MIN buttons to set the stop time. Press CANCEL at any time to clear the setting currently on screen
(i.e.either Start or Stop). If you are not setting weekend programming, just press PROG1 to save your
settings and exit the programming function.
If you wish PROG1 to operate on Saturday and Sunday, press WEEK button to set start time, using
HOUR and MIN buttons as described above. Then press PROG1 again to set the weekend stop time, and
press PROG1 once more to save your settings and exit the setting mode.
Continue as above using PROG2 if required. To check the programme settings press either Prog1 or
Prog2.
...Important Info
Continued on page 10...
Revised 04-08-10 YUNCA Leedz FS Fuzzy Feb 2010 Page 9 of 19