Everglades 275 CC Owner's Manual
  1. Manuals
  2. Brands
  3. Everglades Manuals
  4. Boat
  5. 275 CC
  6. Owner's manual

Everglades 275 CC Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

2012
Owner's Manual
275 cc
295 cc
325 cc

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 275 CC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Everglades 275 CC

Summary of Contents for Everglades 275 CC

  • Page 1 2012 Owner’s Manual 275 cc 295 cc 325 cc...
  • Page 2 Revision 1 10/24/2011...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS ......................3 SAFETY INFORMATION ......................7 BOAT INFORMATION ......................8 SPECIFICATIONS ........................ 9 CERTIFICATIONS & SPECIFICATIONS ...................12 INTRODUCTION & IMPORTANT INFORMATION ...............15 OWNER / OPERATOR INFORMATION ..................17 Chapter 1: SAFETY EQUIPMENT 1.1 General ........................19 1.2 Engine Alarms ......................19 1.3 Neutral Safety Switch ....................19 1.4 Engine Stop Switch .....................19...
  • Page 4 TABLE OF CONTENTS Chapter 4: HELM CONTROL SYSTEMS 4.1 General ........................47 4.2 Engine Throttle and Shift Controls .................47 4.3 Neutral Safety Switch ....................48 4.4 Engine Power Tilt and Trim ...................49 4.5 Engine Stop Switch .....................49 4.6 Steering System ......................50 4.7 Trim Tabs ........................50 4.8 Bow Thruster (Optional) ....................51 4.9 Control Systems Maintenance ..................52 Chapter 5:...
  • Page 5 TABLE OF CONTENTS Chapter 9: DRAINAGE SYSTEMS 9.1 General ........................81 9.2 Cockpit Sole Drains ....................81 9.3 Hardtop Drains ......................81 9.4 Bilge Drainage ......................81 9.5 Fishboxes, Baitwell and Storage Compartment Drains ............82 9.6 Cockpit and Water System Drains ..................83 9.7 Drainage System Maintenance ..................83 Chapter 10: VENTILATION SYSTEM 10.1 Cabin Ventilation .......................85...
  • Page 6 TABLE OF CONTENTS Chapter 14: SEASONAL MAINTENANCE 14.1 Storage and Lay-up ....................119 14.2 Winterizing ......................121 14.3 Recommissioning ....................123 Appendix A: SCHEMATICS 275/295 Center Console Wiring Diagram ................125 325 Center Console Wiring Diagram ...................126 Appendix B: GLOSSARY OF TERMS ......................127 Appendix C: MAINTENANCE LOG ......................131 Appendix D: BOATING ACCIDENT REPORT ....................137...

  • Page 7: Safety Information

    SAFETY INFORMATION Your Everglades owner’s manual has been written to include a number of safety instructions to assure the safe operation and maintenance of your boat. These instructions are in the form of DANGER, WARNING and CAUTION statements. The following definitions apply:...

  • Page 8: Boat Information

    BOAT INFORMATION Please fill out the following information section and leave it in your Everglades owner’s manual. This information will be important for you, your dealer and/or Everglades service personnel to know, if you may need to call them for technical assistance or service.

  • Page 9: Specifications

    SPECIFICATIONS 275 CC Specifications HULL LENGTH OVERALL W/ ENGINE _____________________________________________________ 29’ 3” BEAM ________________________________________________________________________________ 9’ 9” WEIGHT DRY - NO ENGINES ____________________________________________________________ 6,000 DEAD RISE _____________________________________________________________________________ 21 DRAFT WITH ENGINES UP _______________________________________________________________ 20” DRAFT WITH ENGINES DOWN _____________________________________________________________ 33” TRANSOM HEIGHT ______________________________________________________________________ 25”...
  • Page 10 SPECIFICATIONS 295 CC Specifications HULL LENGTH OVERALL W/ ENGINE _____________________________________________________ 31’ 3” BEAM ________________________________________________________________________________ 9’ 9” WEIGHT DRY - NO ENGINES ____________________________________________________________ 6,300 DEAD RISE _____________________________________________________________________________ 21 DRAFT WITH ENGINES UP _______________________________________________________________ 20” DRAFT WITH ENGINES DOWN _____________________________________________________________ 33” TRANSOM HEIGHT ______________________________________________________________________ 25” BRIDGE CLEARANCE TOP OF HARDTOP _____________________________________________________ 8’...
  • Page 11 SPECIFICATIONS 325 CC Specifications HULL LENGTH OVERALL W/ ENGINE _______________________________________________________ 35’ BEAM _______________________________________________________________________________ 10’ 8” WEIGHT DRY - NO ENGINES ____________________________________________________________ 9,000 DEAD RISE _____________________________________________________________________________ 25 DRAFT WITH ENGINES UP _______________________________________________________________ 24” DRAFT WITH ENGINES DOWN _____________________________________________________________ 36” TRANSOM HEIGHT ______________________________________________________________________ 30” BRIDGE CLEARANCE TOP OF HARDTOP ___________________________________________________8’...

  • Page 12: Certifications & Specifications

    To be in compliance with European directives for recreational boats as published by the International Organization for Standardization (ISO) in effect at the time this boat was manufactured, we are providing the following information. Manufacturer: Name Everglades Boats 544 Air Park Road Edgewater, FL Zip Code: 32132...
  • Page 13 To be in compliance with European directives for recreational boats as published by the International Organization for Standardization (ISO) in effect at the time this boat was manufactured, we are providing the following information. Manufacturer: Name Everglades Boats 544 Air Park Road Edgewater, FL Zip Code: 32132...
  • Page 14 To be in compliance with European directives for recreational boats as published by the International Organization for Standardization (ISO) in effect at the time this boat was manufactured, we are providing the following information. Manufacturer: Name Everglades Boats 544 Air Park Road Edgewater, FL Zip Code: 32132...

  • Page 15: Introduction & Important Information

    It has been written to be IMPORTANT: clearly stated and easily understood. If you have any The terms and conditions of the Everglades Boats questions after reading the warranty, please contact Limited Warranty are outlined in the warranty the Everglades Boats Customer Service Department statement included in this manual.
  • Page 16 INTRODUCTION & IMPORTANT INFORMATION Transferring the Limited Structural Warranty Service For a transfer fee, Everglades Boats will offer to All warranty repairs must be performed by an extend a Transferable Limited Structural Hull War- authorized Everglades Dealer. Should a problem ranty to subsequent owners of Everglades Boats.

  • Page 17: Owner / Operator Information

    OWNER / OPERATOR INFORMATION Registration and Numbering an accident. If you need additional information regarding accident reporting, please call the Boat- Federal law requires that all undocumented ves- ing Safety Hotline, 800-368-5647. sels equipped with propulsion machinery be regis- tered in the State of principal use. A certificate of Education number will be issued upon registering the boat.
  • Page 18 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 19: Safety Equipment

    Chapter 1: SAFETY EQUIPMENT 1.1 General Your boat and outboard engines have been equipped with safety equipment designed to en- hance the safe operation of the boat and to meet U.S. Coast Guard safety standards. The Coast Guard or state, county and municipal law enforce- ment agencies require certain additional accessory safety equipment on each boat.

  • Page 20: Required Safety Equipment

    Throwable devices must be immediately available for use. All Non-Pyrotechnic Devices Everglades boats must be equipped with at least Non-Pyrotechnic visual distress signals must be one Type I, II or III PFD for each person on board, in serviceable condition, readily accessible and plus one throwable device (Type IV).

  • Page 21: Navigation Lights

    Safety Equipment • Electric Distress Light (Night use only) • There is no obvious physical damage, corrosion, leakage or clogged nozzles. The electric distress light is accepted for night use only and must automatically flash Refer to the “Federal Requirements And Safety the international SOS distress signal.

  • Page 22: First Aid

    Safety Equipment 1.7 First Aid operated by the National Oceanic and Atmospheric Administration (NOAA) in the United States. The It is the operator’s re- EPIRB should be mounted and registered accord- sponsibility to be familiar ing to the instructions provided with the beacon, with the proper first-aid so that the beacon’s unique distress code can be procedures and be able...

  • Page 23: Caution And Warning Labels

    Safety Equipment 1.9 Caution and Warning Labels The caution and warning labels shown are examples of the labels that could be on your boat. The actual labels and their location could vary on your boat.
  • Page 24 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 25: Operation

    2.1 General the boat as well. Always modify the boat speed in accordance with the sea conditions, boat traffic Before you start the engines on your Everglades, and weather conditions. you should have become familiar with the various component systems and their operation and have Remember, it is the operator’s responsibility to...
  • Page 26 Operation Overtaking Situations When one motor boat is overtaking another mo- tor boat, the boat that is being passed has the right-of-way. The overtaking boat must make the adjustments necessary to provide clearance for a safe passage of the other vessel. The boats should sound the appropriate signals.
  • Page 27 Operation...

  • Page 28: Pre-Cruise Check

    Operation Notice: • Test the automatic and manual bilge pump Storms and wave action can cause buoys to switches to make sure the systems are working move. You should not rely on buoys alone properly. This is particularly important before to determine your position.

  • Page 29: Operating Your Boat

    • Alcohol makes it difficult to correctly judge • Your Everglades is a heavy boat that will speed and distance or track moving objects. produce a large wake at certain speeds. You are responsible for damage and injury caused •...

  • Page 30: Docking, Anchoring And Mooring

    Operation • As different types of engines are used to • Turn off all electrical equipment except the power the boat, have the dealer describe the automatic bilge pumps. operating procedures for your boat. For more • If you are going to leave the boat unattended, instructions on “How To Operate The Boat,”...
  • Page 31 Operation Maneuvering to the Dock Approach the dock slowly at a 30 to 40 degree angle. Whenever possible, approach against the wind or current. Turn the engines straight & shift to neutral when you feel you have enough mo- After Bow Spring Cleat mentum to reach the dock.

  • Page 32: Controls, Steering Or Propulsion System Failure

    Operation Leaving a Mooring WARNING Start the engines and let them warm up for sev- eral minutes before releasing the mooring line. NEVER ANCHOR THE bOAT bY THE STERN. THE STERN The boat will already be headed into the wind, OF THE bOAT IS VULNERAbLE TO SWAMPING FROM WAVE so move it forward enough to loosen the line and ACTION AND WIND AND CURRENT WILL PUT MORE STRESS...

  • Page 33: Flooding Or Capsizing

    It is much easier for the Coast Guard, aircraft or other boats to spot, than people THE MOORING CLEATS ON EVERGLADES bOATS ARE in the water. If your boat is equipped with an NOT DESIGNED OR INTENDED TO bE USED FOR TOWING EPIRB, make sure it is activated.

  • Page 34: Crow's Nest (Optional)

    Operation 2.11 Crow’s Nest (Optional) • Good common sense and judgment must be exercised at all times while someone is riding Your boat could be equipped with an optional in the Crow’s Nest. Crow’s Nest (observation tower). The Crow’s Nest is a powder coated, welded aluminum frame that •...

  • Page 35: Water Skiing And Wakeboarding

    Operation • Check the person for injuries and administer • Secure the ski tow rope to an appropriate device first aid if necessary. If the injuries are serious, intended for ski tow ropes. call for help. Refer to the Safety chapter for •...

  • Page 36: Teak Surfing

    Operation • Never leave a fallen skier alone in the water for any reason and have an observer display a skier down flag to alert other boaters that your skier has fallen. • Agree on hand signals to be used between the observer and skier to communicate.

  • Page 37: Trash Disposal

    Operation 2.15 Trash Disposal 2.16 Trailering Your Boat The discharge of plastic trash or trash mixed with If you trailer your boat, make sure that your tow plastic is illegal anywhere in the marine environ- vehicle is capable of towing the weight of the ment.
  • Page 38 Operation Important: Your Everglades is a heavy boat and care must be taken when selecting the trailer. We recommend that you use a bunk style trailer that incorporates a combination of heavy duty rollers or bunks, to support the keel and long bunks running under and parallel to the stringers to support the hull.
  • Page 39 Operation • The COUPLER MUST BE COMPLETELY OVER • Make sure the LIGHTS on the trailer function THE BALL and the LATCHING MECHANISM properly. LOCKED DOWN. • CHECK THE BRAKES. On a level parking area • Make sure the TRAILER IS LOADED EVENLY roll forward and apply the brakes several times from front to rear as well as side to side and at increasing speeds to determine if the brakes...
  • Page 40 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 41: Propulsion System

    Chapter 3: PROPULSION SYSTEM 3.1 General Your Everglades is designed to be powered with 4-cycle outboard motors. 4-cycle outboard en- gines do not use an oil injection system and are not equipped with remote oil tanks. They have an oil sump in the crankcase that must be kept full of the type of oil recommended by the engine manufacturer.

  • Page 42: Engine Lubrication

    The propellers convert the engine’s power into CAN CAUSE SEVERE DAMAGE TO THE ENGINE. CONTACT thrust. They come in a variety of styles, diameters YOUR EVERGLADES DEALER OR ENGINE MANUFACTURER and pitches. All boats powered by Yamaha engines FOR INFORMATION ON THE PROPER PAINTING PROCEDURES.
  • Page 43 Notice: Outboard engines can be damaged and the warranty void if the boat is not propped correctly. Always consult your Everglades Yamaha Propeller dealer or authorized engine service dealer when making changes to the propellers or if the boat does not run near the top recom- mended RPM.

  • Page 44: Engine Instrumentation

    (RPM). This speed is not the boat speed or necessarily the speed of Most Everglades boats are equipped with Yamaha the propeller. engines and Command Link® Plus LCD multi- function display. This system can be integrated...

  • Page 45: Fuel Gauge

    Propulsion System Speedometer Yamaha Command Link Plus speedometers can ® indicate boat speed via the engine pickup or an optional GPS or depth sounder triducer, if these options are installed in your boat. Refer to the engine gauge and electronics operating manuals for more information on the speedometer options available for your boat.
  • Page 46 Propulsion System Depth Gauge (Optional) Instrument Maintenance The depth gauge indicates the depth of the water Electrical protection for instruments and ignition below the bottom of the boat. circuitry is provided by a set of fuses or circuit breakers located on each engine. The ignition Compass switches should be sprayed periodically with a contact cleaner/lubricant.

  • Page 47: Helm Control Systems

    Chapter 4: HELM CONTROL SYSTEMS 4.1 General The helm controls consist of three systems: the engine throttle and shift controls, the steering system and the trim tab control switches. These systems provide the operator with the ability to control the direction and attitude of the boat from the helm station.

  • Page 48: Neutral Safety Switch

    See your • Station transfer that allows the operator to Everglades dealer for necessary control and cable transfer control from one station to another adjustments. with the push of a button on boats with two helm stations.

  • Page 49: Engine Power Tilt And Trim

    The maximum tilt angle on the Yamaha F350 engines is preset at the factory. If necessary, the maximum tilt angle can be adjusted by your Everglades or Yamaha CAUTION dealer by reprogramming the settings using the Yamaha engine diagnostic system.

  • Page 50: Steering System

    Helm Control Systems 4.6 Steering System Manual Hydraulic Steering (Standard) The steering system is hydraulic and made of three main components: the helm assembly, hydraulic hoses and the hydraulic cylinder. The helm unit acts as both a fluid reservoir and pump. Turning of the helm or steering wheel pumps the fluid in the hydraulic hoses and activates the hydraulic cylin- ders causing the motors to turn.

  • Page 51: Bow Thruster (Optional)

    Helm Control Systems tab operating manual for more information on the operation and programming of the trim tabs. Before leaving the dock, make sure that the tabs are in the full “UP” position. If they are not, press and hold the control in the bow up position for ten (10) seconds to fully retract the tabs.

  • Page 52: Control Systems Maintenance

    Control system adjustments may become neces- When new or after repairs, hydraulic steering sary. If adjustments become necessary, see your systems may need to have all air purged from Everglades dealer. the system. Only use hydraulic steering fluid recommended by the steering system manu- facturer.
  • Page 53 Bow Thruster Maintenance (Optional) Contact your authorized Everglades dealer or the bow thruster manufacturer for information regard- The bow thruster is mounted in the forward bilge ing the correct bottom paint and application.
  • Page 54 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 55: Fuel System

    Chapter 5: FUEL SYSTEM 5.1 General The gasoline fuel system used in Everglades boats is designed to meet or exceed the requirements of the U.S. Coast Guard, the Boating Industry As- sociation and the American Boat and Yacht Council in effect at the time of manufacture.

  • Page 56: Fuel System Maintenance

    325 CC and through the center access hatch in the splashwell on the 275 CC and 295 CC. The filters are the water separator type and should be serviced fre- quently to assure an adequate supply of clean, dry fuel to the engines.

  • Page 57: Fueling Instructions

    RESULT OF USE OF AN ALCOHOL bLEND IS NOT COVERED SPILLED FUEL IS DANGEROUS AND CAN YELLOW FIbERGLASS bY THE EVERGLADES WARRANTY. REFER TO THE ENGINE OR IGNITE. MAkE SURE YOU DO NOT SPILL ANY FUEL. IF FUEL MANUFACTURER OWNER’S MANUAL REGARDING FUEL IS SPILLED ON THE DECk, USE A CLOTH TO REMOVE THE FUEL REQUIREMENTS FOR YOUR ENGINES.

  • Page 58: Fuel System Maintenance

    Fuel System 5.4 Fuel System Maintenance The age of gasoline can effect engine performance. Chemical changes occur as the gasoline ages that Periodically inspect all primer bulbs, connections, can cause deposits and varnish in the fuel system clamps and hoses for leakage, damage or deterio- as well as reduce the octane rating of the fuel.

  • Page 59: Electrical System

    Your Everglades is equipped with 120 volt AC parallel, automatic float switches for bilge pumps and 12 volt DC electrical systems. The AC sys- and the shower sump float switch. Most 12 volt...
  • Page 60 Electrical System Battery and Parallel Switches 275/295 Models These batteries should be of the size and capac- ity recommended by the manufacturer of your engines. These specifications should be consid- ered to be the minimum size battery required. Consider increasing the capacity of the batteries if you will be trolling, drift fishing or have extensive electronics on board.
  • Page 61 Electrical System 325 Center Console Battery and 325 Center Console Voltage Sensitive Relays Emergency Parallel Switches Batteries and Battery Switches 325 CC knob on each battery switch that can be pressed to manually activate the switch or rotated to reac- The 325 CC has provision for four batteries tivate remote activation of the switch or to lockout mounted in fiberglass battery boxes in the systems...
  • Page 62 Electrical System each engine. The engine and house batteries are also charged by the battery charger whenever it is operating. The VSR battery isolator systems manage the charging current for the 12 volt system whenever the engines are running. The systems automati- cally sense the condition of each battery and direct the available current to the batteries that require charging.

  • Page 63: Dc System Switch And Circuit Breaker Panels

    Yamaha Command Link Plus Ignition ® Most Everglades boats are equipped with Yamaha engines and the Command Link Plus ignition key ® panels that offer the latest in technology and du- rability.
  • Page 64 Baitwell Recirc Activates the baitwell pump that recirculates the Reserved for additional DC accessories installed water in the baitwell. by you or your Everglades dealer.
  • Page 65 Electrical System House Remotely activates the House battery switch. A red LED light in each switch glows when the bat- tery switch it controls is activated. Slide the label down and press the top of the switch to activate the indicated battery switch. Slide the label up and press the bottom of the switch to turn the indicated battery switch off.
  • Page 66 Electrical System Dash LT Activates the lights above the helm area. Hardtop Light CTSY LT A three position switch that actives the overhead lights in the in the Hardtop liner. The center po- sition is OFF. Moving the switch in one direction will activate the white overhead lights.
  • Page 67 Electrical System The circuit breakers are labeled for the accessory circuit they protect. Circuit breakers labeled ACC are reserved for additional accessories not usually installed by the factory. If a breaker trips, the reset button pops out and is visible through the silicone protective cover. Press the button to reset the tripped breaker.
  • Page 68 Electrical System Notice: If a main circuit breaker trips, always make sure the problem that caused the breaker to trip is found and corrected before resetting the breaker. The following are the main circuits supplied and protected by heavy duty circuit breakers: Main Protects the circuit that supplies 12 volt current to the head compartment DC breaker Panel.

  • Page 69: Bonding System

    Electrical System Battery All Protects the circuits for the remote main battery switches located in the helm switch panel. Each battery switch is equipped with a manual override to enable the operator to activate the switch in the event that the remote circuit fails. A red LED light glows when the switch is activated.

  • Page 70: Ac Electrical System

    Electrical System 6.6 AC Electrical System DANGER TO REDUCE THE RISk OF ELECTRICAL SHOCk IN WET WEATHER, AVOID MAkING CONTACT WITH THE SHORE CAbLE OR MAkING A CONNECTION TO A LIVE SHORE OUTLET. NEVER SPRAY WATER ON ELECTRICAL CAbLES WHILE WASHING DOWN DECkS.

  • Page 71: Electrical System Maintenance

    Electrical System Battery Charger Operation AC electrical current is supplied directly to the automatic battery charger, located in the systems compartment, by the shore power cord and AC inlet plug near the transom door. The battery charger will charge and maintain the 12 volt bat- teries simultaneously when activated.
  • Page 72 Electrical System Your boat is equipped with batteries that are in- stalled by your dealer. Some marine batteries are maintenance free with cells that are sealed and do not require inspection or service. Standard marine batteries are the wet cell type that are not maintenance free.

  • Page 73: Fresh Water System

    PUMPS ARE NOT DESIGNED TO PUMP FUEL AND A FIRE OR ExPLOSION COULD RESULT. CONTACT YOUR DEALER Whenever the boat is left unattended, the Fresh OR THE EVERGLADES CUSTOMER SERVICE DEPARTMENT Water switch should be placed in the OFF position. FOR ASSISTANCE IN HAVING THE FUEL PROFESSIONALLY REMOVED AND COMPONENTS OF THE FRESH WATER SYSTEM REPLACED AS NECESSARY.

  • Page 74: Fresh Water System Maintenance

    Fresh Water System Head Sink and Shower (295/325 Models) The vanity sink faucet converts to a retractable hand-held shower head. To use the shower, pull the shower head out of faucet and the turn on the cold water valve. Make sure the Fresh Water switch in the helm switch panel is activated before using the shower.
  • Page 75 Fresh Water System • Add a commercially available potable water conditioner to the water tank to keep it fresh. Notice: The fresh water system must be properly winterized prior to winter lay-up. Refer to the section on winterizing for more informa- tion.
  • Page 76 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 77: Raw Water System

    If this procedure doesn’t work, contact your Everglades dealer. Closing the thru-hull valves before the boat is hauled from the water will help to eliminate air locks in raw water systems.

  • Page 78: Baitwell

    Raw Water System Washdown Hose Connector The raw water washdown hose connection is lo- cated on the port side of the cockpit below the gunnel and uses a standard garden hose connec- tor. It is equipped with a valve that allows the flow of water to be turned on or off.

  • Page 79: Raw Water System Maintenance

    Raw Water System To drain the baitwell, turn off the baitwell pump and remove the plug in the drain fitting. When the baitwell has completely drained, use the wash- down hose to flush the baitwell and drain of debris. The baitwell seacock valve should be closed when- ever the baitwell is not in use.
  • Page 80 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 81: Drainage Systems

    9.2 Cockpit Sole Drains Your Everglades has two scupper drains located in the rear of the cockpit. A flap built into the scup- per drain fitting on 275/295 models reduces the surge of seawater through the scupper and into the cockpit while maneuvering or in rough water.

  • Page 82: Fishboxes, Baitwell And Storage Compartment Drains

    Drainage Systems Notice: See Electrical Systems for additional infor- mation on bilge pump operation. When the boat is out of the water the bilge can be drained by a garboard drain located in the transom near the bottom of the hull. The plug should be removed whenever the boat is hauled out of the water and installed just prior to launching.

  • Page 83: Cockpit And Water System Drains

    Drainage Systems Monitor the water level as the pump drains the fishbox and turn it off immediately when draining is complete. The pump could be damaged if it is allowed to run dry for extended periods. Aft Fishbox (325 Center Console) The aft fishbox in the 325 Center Console drains by gravity to a thru-hull fitting in the hull.
  • Page 84 Drainage Systems • Flush all gravity drains with fresh water to keep Note: All drains and pumps must be properly winterized before winter lay-up. them clean and free flowing. • Clean fishbox pump out strainers after each CAUTION use to keep them clean and free flowing. •...

  • Page 85: Ventilation System

    Chapter 10: VENTILATION SYSTEM 10.1 Cabin Ventilation Cabin Door & Vents An opening panel and vents in the cabin door provide ventilation to the head compartment. The door itself is held in the open position by an automatic magnetic latch. Make sure the door is fully latched in the closed position before operat- ing the boat above idle speed.

  • Page 86: Windshield Ventilation

    Ventilation System 10.2 Windshield Ventilation The windshield can be lowered to provide ven- tilation at the helm and improved visibility. The windshield is raised and lowered by an hydraulic cylinders activated by an electric hydraulic pump in the head compartment. The system is controlled by the Windshield switch in the hardtop switch panel.

  • Page 87: Exterior Equipment

    The roper locker is drained by a thru-hull fitting in the hull side near the bottom of the locker. It EVERGLADES bOATS ARE NOT EQUIPPED WITH HARDWARE is very important to check the drain frequently to DESIGNED FOR TOWING PURPOSES. THE MOORING CLEATS make sure it is clean and free flowing.

  • Page 88: Center Console Rope Locker And Windlass

    Exterior Equipment The anchor is lowered by releasing the anchor from the chain binder on the roller assembly and operating a “DOWN” control at the helm. After the anchor is set, the windlass must not be left to take the entire force from the anchor line. Boats lying to their anchor in a high swell or heavy weather conditions will snub on the line.
  • Page 89 Exterior Equipment in slightly to relieve the tension on the binder, Periodically remove the anchor line from the rope then rotate the binder up to the full release posi- locker, rinse it with fresh water and allow it to dry tion.

  • Page 90: Hull

    Stern Boarding Ladder 11.4 Hull Engine Mounting System and Swim Platform Your Everglades is equipped with an engine mounting system that is integrated into the hull and stringer system that is designed to distribute the stresses of engine weight and thrust through- out the entire hull.

  • Page 91: Cockpit Features All Models

    Exterior Equipment 11.5 Cockpit Features All Models General Most hatches and doors in the cockpit are secured with special cam action, draw or automatic “push EMERGENCY to close” latches. Gas charged springs are used DRAIN PORT on most hatches that help raise the hatches and hold them in the open position.

  • Page 92: 275/295 Center Console Cockpit Equipment

    Exterior Equipment WARNING OPERATING THE bOAT UNDER POWER WITH THE TRANSOM DOOR OPEN MAY ALLOW PERSONS TO FALL OVERbOARD AND INTO bOAT PROPELLERS OR TO bE LOST IN OPEN WATER. ALWAYS CHECk TO MAkE SURE THE TRANSOM DOOR IS PROPERLY CLOSED AND LATCHED bEFORE STARTING THE ENGINES AND NEVER OPERATE THE bOAT UNDER POWER WITH THE TRANSOM DOOR OPEN.
  • Page 93 Exterior Equipment Notice: Periodically inspect the dive door hinges and hardware for wear, damage or loose fit. Any problems found should be corrected immediately. WARNING THE DIVE DOOR SHOULD bE CLOSED AND PROPERLY LATCHED WHENEVER THE ENGINES ARE RUNNING. NEVER OPEN THE DIVE DOOR WHILE UNDERWAY OR IN ROUGH SEA CONDITIONS.
  • Page 94 Exterior Equipment ting in the hull. The baitwell is supplied seawater by a raw water pump located in the stern bilge. Another pump can be activated by a switch in the helm panel to recirculate and aerate the water in the baitwell.
  • Page 95 Exterior Equipment Systems Compartment Access The aft seat assembly is also the access hatch for the systems compartment in the stern. The seat recess is hinged at the top and secured in the down position by two twist lock latches. Two gas springs help lift the seat/hatch assembly and hold it in the open and closed positions.
  • Page 96 Exterior Equipment seats to a leaning post style seat with a backrest, allowing the operator and passenger to sit or stand at the helm. To convert each seat to a leaning post, lift the front of the seat cushion to raise the bolster and push it back above the seat cushion.
  • Page 97 Exterior Equipment A molded recess located in the seat base below the seats is designed for fire extinguishers. The recessed mounting location keeps the fire extin- guishers out of the way and readily available. Bow Seats and Storage Compartments There are 2 storage compartments located in the bow below the seats that are secured with lockable “push to close”...

  • Page 98: Center Console Cockpit Equipment

    Exterior Equipment 11.7 325 Center Console Cockpit Equipment Dive Door and Boarding Ladder (Optional) A dive door in the port hull side is available as optional equipment. The door provides divers and swimmers easy, unobstructed access to the water and cockpit. It also makes boarding and exiting the boat much easier in many docking situations.
  • Page 99 Exterior Equipment secured in the ladder bracket by a spring loaded latch that prevents the ladder from floating off the bracket. To remove the ladder, push up on the release lever on the side of the ladder bracket to release the latch, then slide the ladder up and off the bracket.
  • Page 100 Exterior Equipment To use the seats, swing the bolster up, then pull the top of the seat toward the cockpit. The bottom of the seat slides in a track and two side supports move out with the seat as it folds out. The seat automatically locks into the seating position when the cushion reaches the full down position.
  • Page 101 Exterior Equipment door closed and secured with both latches before operating the boat. Seat Base and Helm Seats The helm and passenger seats are equipped with a flip up bolster to provide more room between the seats and the helm. The bolsters convert the seats to a leaning post style seat with a backrest, allow- ing the operator and passenger to sit or stand at the helm.

  • Page 102: Center Console And Helm

    There are also fuse panels that provide protection for equipment installed by Everglades or other equipment added by you or dealer. The rear of the helm is hinged at the bottom and opens to provide access to service control and steering system components.
  • Page 103 Exterior Equipment To open the helm station, make sure the engines are not running and hold the helm in the closed position while another person releases the latches that secure the helm inside the head compart- ment. Carefully lower the helm to the full open position.
  • Page 104 Console Windshield Closed The windshield wiper and washer is standard on your Everglades boat. A special lockout mecha- nism prevents the windshield wiper or washer from activating unless the windshield is in the full up (closed) position.

  • Page 105: Hardtop

    Exterior Equipment Head Compartment Door The head compartment door on the port side of the console is equipped with vents near the bot- tom of the door and an opening vent panel. A magnetic latch automatically secures the door in the open position and a lockable, push to close latch secures the door when it is closed.

  • Page 106: Crow's Nest (Optional)

    Crow’s Nest. you should contact Everglades Customer Service to make sure the equipment you would like to Do not overload the Crow’s Nest. It is designed...

  • Page 107: Interior Equipment

    Chapter 12: INTERIOR EQUIPMENT 12.1 275 Center Console Head Compartment The head compartment is equipped with a marine toilet and storage. The compartment drains to the bilge through a drain fitting in the floor. Daylight and ventilation is provided by an open- ing port window and an opening vent panel in the cabin door.

  • Page 108: 295/325 Center Console Head Compartment

    Interior Equipment 12.2 295/325 Center Console Head Compartment The head compartment is equipped with a fresh water sink and faucet that converts to a shower by pulling the faucet out of the base. The shower wa- ter drains to the sump system where it is pumped overboard.
  • Page 109 Interior Equipment A switch panel with a key activated lockout is lo- cated on the starboard side of the head compart- ment. The overboard macerator discharge pump and discharge valve is behind the starboard access panel in the head compartment. The pump dis- charges holding tank waste to a thru-hull fitting in the hull below the waterline.
  • Page 110 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 111: Routine Maintenance

    Chapter 13: ROUTINE MAINTENANCE 13.1 Exterior Hull and Deck CAUTION Hull Cleaning-Below The Water Line When the boat is removed from the water, clean bARRIER COATINGS AND bOTTOM PAINT SHOULD bE the outer bottom surface immediately. Algae, APPLIED ONLY bY QUALIFIED MARINE PROFESSIONALS grass, dirt and other marine growth is easier to IN A bOAT YARD OR DEALERSHIP THAT SPECIALIZES IN THEIR APPLICATION.
  • Page 112 Do not use abrasives, bleaches, ammonia, low quality anodes could be the problem. Contact acids or harsh detergents. See your dealer for your dealer or Everglades Customer Service for special marine formulations. Harsh abrasive the proper size and type of anodes to be used and and chemical cleaners are not recommended the specific installation procedure.
  • Page 113 Routine Maintenance • Stainless Steel can normally be cleaned and CAUTION protected by using a high quality boat or au- tomotive wax or a commercial metal cleaner ONE DRAWbACk TO METAL PROTECTORS IS THAT THEY CAN and protectant. MAkE THE METAL SLIPPERY. THEREFORE, THEY SHOULD bE NOT bE USED ON TOWER LADDERS, STEERING WHEELS AND Never do the following on Stainless Steel.

  • Page 114: Vinyl Upholstery

    Your dealer or the engine manufacturer can provide additional information on fuel degradation Notice: and fuel stabilizers recommended for your engine. You should contact Everglades Customer Service before making any modifications to In many states, most gasoline is blended with aluminum fabrications. Unauthorized modi- ethanol alcohol.
  • Page 115 Routine Maintenance and water. Any stain, spill or soiling should be will deteriorate the waterproofing in the fabric. cleaned up promptly to prevent the possibility of The underside can be brushed with a soft brush permanent staining. When cleaning, always rub and sprayed with a disinfectant to prevent the gently.

  • Page 116: Interior

    If you have any questions about extend the life of the curtains. the clear curtains used on your boat, please con- tact the Everglades Customer Service Department. Vinyl curtains should be stored either rolled or flat, without folds or creases. Folding the curtains...

  • Page 117: Bilge, Pumps And Components

    Routine Maintenance If you leave the boat for a long period of time, Periodically check the bilge pumps and alarms for put all cushions on their sides, open all interior proper operation and clean debris from the strain- cabin and locker doors and hang a commercially ers and float switches.
  • Page 118 Routine Maintenance • Operate the thru-hull valves once a month and • Clean the cockpit drains with a hose to remove service as required. debris that can block water drainage. • Run all overboard pumps briefly at least once • Clean the hardtop leg drain holes.

  • Page 119: Seasonal Maintenance

    For more recommendations properly support your boat and that it is rated for your specific area, check with your local to support the weight. Everglades dealer. • Make sure the trailer is on a level surface and •...
  • Page 120 FOR THE HULL. HULL DAMAGE RESULTING FROM IMPROPER Vacuum all carpets and dry clean drapes and CRADLE OR TRAILER SUPPORT IS NOT COVERED bY THE upholstery. EVERGLADES WARRANTY. • Remove cushions and open as many locker doors as possible. Leaving as many of these areas open as possible will improve the boat’s...

  • Page 121: Winterizing

    Seasonal Maintenance • Clean the exterior upholstery with a good the solution. Run the pumps one at a time until vinyl cleaner and dry thoroughly. Spray the the antifreeze solution is visible at all raw water weather covers and boat upholstery with a faucets and discharge fittings and drains.
  • Page 122 Do not store the boat Everglades dealer. in a damp storage enclosure. Excessive damp- ness can cause electrical problems, corrosion and Hardtop excessive mildew.

  • Page 123: Recommissioning

    Seasonal Maintenance 14.3 Recommissioning • Check all hose clamps for tightness. WARNING • Pump the antifreeze from the fresh and raw water systems and flush several times with fresh water. DO NOT OPERATE THE bOAT UNLESS IT IS COMPLETELY ASSEMbLED. kEEP ALL FASTENERS TIGHT.
  • Page 124 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 125: Appendix A: Schematics

    Appendix A: SCHEMATICS                                      ...

  • Page 126: Center Console Wiring Diagram

    Schematics                                        ...

  • Page 127: Appendix B: Glossary Of Terms

    Appendix B: GLOSSARY OF TERMS ft: In, near or toward the stern of a boat. Bow Rail: Knee high rails of solid tubing to aid in preventing people from falling overboard. Aground: A boat stuck on the bottom. Bridge: The area from which a boat is steered Amidships: In or toward the part of a boat midway and controlled.
  • Page 128 Glossary of Terms Grab Rail: Hand-hold fittings mounted on cabin eck: The floor-like platform of a boat that tops or sides for personal safety when moving covers the hull. around the boat, both on deck and below. Displacement: The volume of water displaced by Ground Tackle: A general term including anchors, the hull.
  • Page 129 Glossary of Terms Length On The Waterline (l.w.l.): A length mea- Pile or Piling: A long column driven into the bot- surement of a boat at the waterline from the stern tom to which a boat can be tied. to where the hull breaks the water near the bow. Pitching: The fore and aft rocking motion of a Limber Hole: A passage cut into the lower edges boat as the bow rises and falls.
  • Page 130 Glossary of Terms Scupper: An opening in the hull side or transom affrail: Rail around the rear of the cockpit. of the boat through which water on deck or in the cockpit is drained overboard. Thru-hull: A fitting used to pass fluids (usually Seacock: Safety valves installed just inside the water) through the hull surface, either above or below the waterline.

  • Page 131: Appendix C: Maintenance Log

    Appendix C: MAINTENANCE LOG Service/Repairs Date Dealer Hours...

  • Page 132: Maintenance Schedule And Log

    Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...
  • Page 133 Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...
  • Page 134 Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...
  • Page 135 Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...
  • Page 136 Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...

  • Page 137: Boating Accident Report

    BOATING ACCIDENT REPORT Appendix D:                                       ...
  • Page 138 Boating Accident Report                                      ...
  • Page 139 Boating Accident Report                                                  ...
  • Page 140 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 141: Appendix E: Float Plan

    Appendix E: FLOAT PLAN Everglades recommends filling out a float plan each time you use your boat for an off- shore day trip or a long cruise. Leave this information with a responsible person ashore, like a close friend or relative that you know well.
  • Page 142 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 143: Troubleshooting Guide

    Appendix F: TROUBLESHOOTING GUIDE PRObLEM CAUSE AND SOLUTION CONTROL SYSTEMS Hydraulic Steering is slow to respond & erratic. • Steering system is low on fluid. Fill and bleed system. • Steering system has air in it. Fill and bleed system. • A component in the steering system is binding. Check and adjust or repair binding component.

  • Page 144: Engine Problems

    Troubleshooting Guide PRObLEM CAUSE AND SOLUTION ENGINE PROBLEMS An engine is running too hot. • The engine raw water pick up strainer is clogged with marine growth. Clean pick up. • The engine raw water pump impeller is worn or damaged. Repair the pump.

  • Page 145: Accessory Problems

    Troubleshooting Guide PRObLEM CAUSE AND SOLUTION ACCESSORY PROBLEMS The baitwell pump runs, but does not pump water. • The strainer on the intake scoop is clogged preventing the water from getting to the pump. Put the boat in reverse to clean the strainer.
  • Page 146 Troubleshooting Guide PRObLEM CAUSE AND SOLUTION ACCESSORY PROBLEMS The automatic float switch on the bilge pump raises but • The circuit breaker or fuse for the automatic switch has does not activate the pump . tripped or blown. Reset the circuit breaker or replace the fuse.
  • Page 147 CAUSE AND SOLUTION...
  • Page 148 Everglades Boats 544 Air Park Road Edgewater, Florida 32132...

This manual is also suitable for:

295 cc325 cc2015 255 cc2015 275 cc2015 295 cc2015 325 cc ... Show all

Table of Contents

Save PDF