Table of Contents
Advertisement
Quick Links
WARNING:
Improper installation, adjustment, alteration, service or
maintenance can cause injury, property damage, or loss
of life. Refer to this manual. For assistance or additional
information consult an authorized installer, service agency
or the gas supplier.
FOR YOUR SAFETY:
Do not store or use gasoline or other fl ammable vapours and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by an authorized
installer, service agency or the gas supplier.
Tested by:
918-988
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
HZI234E Gas Insert
MODELS:
HZI234E-NG Natural Gas
Owners & Installation Manual
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
HZI234E-LP Propane
FOR YOUR SAFETY:
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you
cannot reach your gas
supplier, call the fi re department.
11/15/12
Advertisement
Table of Contents
Related Manuals for Regency HZI234E-NG
Summary of Contents for Regency HZI234E-NG
- Page 1 HZI234E Gas Insert MODELS: HZI234E-NG Natural Gas HZI234E-LP Propane Owners & Installation Manual WARNING: FOR YOUR SAFETY: Improper installation, adjustment, alteration, service or What to do if you smell gas: Do not try to light any appliance maintenance can cause injury, property damage, or loss ...
- Page 2 The HZI234E Direct Vent Gas Insert has been designed to provide you with all the warmth and charm of a fi replace, at the fl ick of a switch. The HZI234E-NG and HZI234E-LP have been approved by Warnock Hersey for both safety and effi ciency.
-
Page 3: Table Of Contents
886 S.I.T. Valve ............16 WARRANTY Description..............16 Conversion from NG to Lp ...........17 Warranty...............51 Glass Crystals or optional ceramic stones ....20 Installation On Burner ..........20 Optional Pebble / Crystal Installation......21 for Firebox Base ............21 ® Regency HZI234E Direct Vent Gas Insert... -
Page 4: Safety Label
Certified for / Certifiée pour: CANADA AND U.S.A. 4001172 is the correct one. NATURAL GAS FIREPLACE INSERT: MODEL HZI234E-NG Factory Equipped For Altitude 0-4500ft. (0-1370m) Min. Supply Pressure 5“ (1.25 kpa) Low Setting Man. -
Page 5: Requirements
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. ® Regency HZI234E Direct Vent Gas Insert... -
Page 6: Dimensions
2 " with screwhead + grommet 628mm for electrical cord 394mm 4 " 374mm 3" 3" [76mm] [76mm] 8 " 276mm 1" 26mm 8 " 20" 48mm 510mm 8 " 739mm 8 " 836mm ® Regency HZI234E Direct Vent Gas Insert... -
Page 7: Dimensions W/ Low Profi Le 4 Sided Faceplate
2 " with screwhead + grommet 628mm for electrical cord 394mm 4 " 374mm 3" 3" [76mm] [76mm] 8 " 276mm 1" 26mm 20" 8 " 510mm 48mm 8 " 739mm 8 " 836mm ® Regency HZI234E Direct Vent Gas Insert... -
Page 8: Dimensions W/ Contemporary And Contour Faceplate
DIMENSIONS W/ CONTEMPORARY AND CONTOUR FACEPLATE 27-1/2” (699mm) 27-3/4” (705mm) 19-1/2” (495mm) 19-1/2” (495mm) Contemporary Faceplate Contour Faceplate 24-3/4” (629mm) 11-3/4” (299mm) 3” (76mm) 14-3/4” (375mm) Contemporary Faceplate 60° 2-1/2” (64mm) Contour Faceplate 13” (330mm) ® Regency HZI234E Direct Vent Gas Insert... -
Page 9: Installation
YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE. CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPE- CIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. ® Regency HZI234E Direct Vent Gas Insert... -
Page 10: Important Message
fi replace. cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fi replace re-approved by the authority having jurisdiction." ® Regency HZI234E Direct Vent Gas Insert... -
Page 11: Installation Checklist
8) Test gas pressure, refer to the "Gas Pipe Pressure Testing" section. Check aeration system, refer to "Gas Insert Aeration Systems" section. 9) Install standard and optional features. Refer to the following sections where applicable: ® Regency HZI234E Direct Vent Gas Insert... -
Page 12: Minimum Clearances To Combustibles
12” Mantel * Alcove side wall must have a min. of 8" clearance. 24-1/2” 4” Mantel 1” Mantel 56” to ceiling 17-1/2” 15-1/2” Top of Door Frame 15-5/8” (397mm) to floor Diagram 1 ® Regency HZI234E Direct Vent Gas Insert... -
Page 13: Venting
Dura-Vent System (46dva-GK adapter and 46dva-VCH high-wind cap). The Air Intake pipe must be attached to the inlet air collar of the termination cap. *NOTE: Simpson Duravent can only be used with 3" and 3" liners. ® Regency HZI234E Direct Vent Gas Insert... -
Page 14: Converting From 3" & 3" Venting To 3" & 2
5) Once the vent restrictor plate is in the required position, secure using the 4 screws removed from step 3. 6) Re-install panels if removed. 7) Re-install glass door. Top Plate with 2" Collar shown on Unit ® Regency HZI234E Direct Vent Gas Insert... -
Page 15: Flue Liner Installation
Note: Aeration Adjustment should only be performed by an authorized to inlet and vent collars. FPI Installer at the time of installation or service. ® Regency HZI234E Direct Vent Gas Insert... -
Page 16: High Elevation
INSTALLATION PILOT ADJUSTMENT 886 S.I.T. VALVE HZI234E-NG SYSTEM DATA DESCRIPTION Min. Supply Pressure 5" WC (1.25 kpa) Periodically check the pilot fl ames. Correct fl ame Manifold Pressure 3.5" WC (0.87 kpa) pattern has two strong blue fl ames: 1 fl owing Orifi... -
Page 17: Conversion From Ng To Lp
Repeat for right side. b) Swing the door out 45 degrees and lift up and out. ® Regency HZI234E Direct Vent Gas Insert... - Page 18 Install the new Pressure Regulator using the 2x M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that the screw threads are cross threaded or stripped, replace the valve assembly. ® Regency HZI234E Direct Vent Gas Insert...
- Page 19 HZI234E: Reverse steps 12-1 on previ- ous pages.. Check for gas leaks. Check inlet and outlet pressures. Check operation of fl ame control. Installer Notice: These instructions must be left with the appliance. ® Regency HZI234E Direct Vent Gas Insert...
-
Page 20: Glass Crystals Or Optional Ceramic Stones
Optional Ceramic Spa Stones shown on burner. For units P33S, P33SE, L676S, U32S, U32SE, E33S only For units P33S,P33SE L676S, U32S, U32SE, E33S only Glass Crystals shown on Burner and Firebox Floor For Units HZI390E, HZI390EB, HZI540EB only ® Regency HZI234E Direct Vent Gas Insert... -
Page 21: Optional Pebble / Crystal Installation
Natural River Pebbles shown surrounding the a Horizon Burner River Pebbles shown surrounding a Sunrise Burner Glass Crystals shown surrounding the Burner ® Regency HZI234E Direct Vent Gas Insert... -
Page 22: Refl Ective Panel Installation
6) Reinstall glass door - reinstall faceplate. 4) Install the left side panel - secure in position with one panel clip and 7) Final installation one screw, as shown in the diagram below. ® Regency HZI234E Direct Vent Gas Insert... -
Page 23: Glass Door Removal / Installation
Place the spring hook through the glass door and screen door. Repeat for right side Spring Hook Spring Hook Top Mounting Bracket Top Mounting Bracket Spring Hook 2) To install the door - reverse steps. ® Regency HZI234E Direct Vent Gas Insert... -
Page 24: Low Profi Le Faceplate Installation
3) From the right side of the unit, remove the on/off switch box cover, one screw top and bottom. Connect the red female ON/OFF valve connec- tors to the ON/OFF switch located on the right faceplate panel. ® Regency HZI234E Direct Vent Gas Insert... - Page 25 12) Install the bottom louver by placing the louver tabs into the slots on the bottom of the unit - in locations shown below. Install logo in lower left hand corner of the front low profi le faceplate. Logo Bottom louver ® Regency HZI234E Direct Vent Gas Insert...
-
Page 26: Contour & Contemporary Faceplate
Tighten screws to secure. See diagram 2. Diagram 4 Faceplate shown on unit without left and right side panels to show keyhole mounting. Diagram 2 ® Regency HZI234E Direct Vent Gas Insert... - Page 27 9) Remove the grommet from the bracket on the left side of the unit. See diagram 7. NOTE: Ensure connectors are tucked in behind the mounting bracket to allow the side faceplate panel to close easily. Grommet Diagram 7 Diagram 10 ® Regency HZI234E Direct Vent Gas Insert...
- Page 28 14) Close the left side faceplate panel. 15) Fit the bottom louver into the slots at the bottom of the fi rebox as shown Contemporary Faceplate in diagram 12. Contour Faceplate Diagram 12 ® Regency HZI234E Direct Vent Gas Insert...
-
Page 29: Optional Backing Plate
The inside of the backing plate may be cut as required using a metal cutting blade. Do not cut the outside edges. Rear View of Diagram 2 Backing Plate ® Regency HZI234E Direct Vent Gas Insert... - Page 30 2 screws on each side as shown in diagram 4. Faceplate shown on unit without left and right side faceplate panels to show mounting of left and right side backing plate. Diagram 4 8) Close the left and right side faceplate panels. ® Regency HZI234E Direct Vent Gas Insert...
-
Page 31: Optional Hearth Trim-Contour/Standard Faceplate
2) Align the screw holes on the hearth trim with the screw holes on the fl anges on the left and right side faceplate. Secure in place using 2 screws on each side as shown in diagram 1. 3) Close the left and right side faceplate panels. ® Regency HZI234E Direct Vent Gas Insert... -
Page 32: Optional Hearth Trim - Low Profi Le Faceplate
Reattach the top piece of the hearth trim to the cut bottom piece by fi tting in place. Diagram 1 Completed Hearth Trim Installation: ® Regency HZI234E Direct Vent Gas Insert... -
Page 33: Profl Ame Remote Control Receiver Installation
Disconnect Red and Black from the Green and White wire. 5) Feed the receiver end of the wire harness under the front edge of fi rebox from right to left. Green White Black ® Regency HZI234E Direct Vent Gas Insert... - Page 34 Receiver 7) Place the wire harness under the fi rebox into the wire clip holders Cover Plate 11) Program remote as per Profl ame remote manual. Wire Clip Wire harness 12) Reinstall faceplate. ® Regency HZI234E Direct Vent Gas Insert...
-
Page 35: Optional Wall Thermostat Installation
3) Connect one thermostat lead to female connector, using male spade con- nector - see pic below. When complete turn remote receiver to the ON position. Unit will now operate using the wall thermostat. ® Regency HZI234E Direct Vent Gas Insert... -
Page 36: Wiring Diagram
Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. ® Regency HZI234E Direct Vent Gas Insert... -
Page 37: Ac Power Adaptor Installation (For Surefi Re Systems)
5) Neatly tuck any loose AC Power Adaptor wires neatly underneath / inside the appliance. Note: (keep wires away from the heat as much as possible). FCM - COM ® Regency HZI234E Direct Vent Gas Insert... -
Page 38: Fan Wiring Diagram
Caution: Ensure that the wires do not touch any CAUTION: Label all wires prior to disconnection hot surfaces and are away from sharp edges. when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. ® Regency HZI234E Direct Vent Gas Insert... -
Page 39: Operating Instructions
fi lm will bake on and become very diffi cult to remove. Use a non-abrasive cleaner and DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS HOT. ® Regency HZI234E Direct Vent Gas Insert... -
Page 40: Copy Of Lighting Plate Instructions
Appuyez sur le bouton ON / OFF Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction pour plus de détails. DO NOT REMOVE THIS INSTRUCTION PLATE 918-628b ® Regency HZI234E Direct Vent Gas Insert... -
Page 41: Maintenance Instructions
MAINTENANCE FPI dealer only, do not use substitute materials WARNING: CHILDREN AND ADULTS (Regency Glass part # 940-355/P). Follow SHOULD BE ALERTED TO THE Conduct an inspection of the venting system our step-by-step instructions for replacement. -
Page 42: Fan Replacement
7) Lift out the bottom tray. 12) Slide pilot hood forward, then pull up and off. 8) Remove the burner by removing 3 screws. 9) Slide burner forward and lift up and out. Top Mounting Bracket ® Regency HZI234E Direct Vent Gas Insert... - Page 43 17) Remove the fan by sliding forward, then lift the fan up and out. 18) Remove the ground screw holding the ground wire. Ground Wire Fan Cover Plate Removal 15) Unplug fan access wires. 19) Reverse steps to install fan. ® Regency HZI234E Direct Vent Gas Insert...
-
Page 44: Valve Assembly Replacement
8) Lift out the bottom tray. b) Swing the door out 45 degrees and lift up and out. Spring Hook 9) Remove the burner by removing 3 screws. 14) Reverse steps to reinstall. ® Regency HZI234E Direct Vent Gas Insert... -
Page 45: Parts List
Valve Assy LP 940-355/P Neoceram Glass 904-241 Orifi ce #56 LP 946-678 Colbalt Fireglass 904-622 Orifi ce #48 NG 566-010 False Tray 904-658 Inlet fl ex gas line 566-908 Enamel Panels 910-142 Thermosdisc 918-988 Manual ® Regency HZI234E Direct Vent Gas Insert... -
Page 46: And 4 Sided Low Profi Le Faceplate Assembly
3 sided low profi le front frame 566-926 4 sided low profi le faceplate 4 sided low profi le back plate 4 sided low profi le front frame 566-030 Bottom louver 566-528 Optional screen door ® Regency HZI234E Direct Vent Gas Insert... -
Page 47: Faceplate Assembly
Contemporary Faceplate 61) 536-914 Contour Faceplate 62) 910-246 Burner ON/OFF Switch 63) 910-330 Fan Speed Control 120 V 64) 904-569 Fan Speed Control Knob 65) 536-125 Fan Switch Bracket ® 66) 948-216 Regency Logo ® Regency HZI234E Direct Vent Gas Insert... -
Page 48: Backing Plate & Hearth Trim Assembly
81) * Left Side 82) * Right Side 83) * 84) * Left Corner 85) * Right Corner 536-940 Hearth Trim 86) * 87) * Bottom * Not available as a replacement part. ® Regency HZI234E Direct Vent Gas Insert... - Page 49 NOTES ® Regency HZI234E Direct Vent Gas Insert...
- Page 50 NOTES ® Regency HZI234E Direct Vent Gas Insert...
-
Page 51: Warranty
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers. - Page 52 Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency and Horizon are trademarks of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2011, FPI Fireplace Products International Ltd. All rights reserved.