DITEC CUBIC6 Installation And Maintenance Manual
Swing gates
Hide thumbs
Also See for CUBIC6:
- Installation and maintenance manual (8 pages) ,
- Instructions manual (16 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DITEC CUBIC6
Summary of Contents for DITEC CUBIC6
- Page 1 CUBIC6 IP1812EN- rev. 2012-07-10 Installation and maintenance manual for swing gates. (Original instructions) DITEC S.p.A. Via Mons. Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY Tel. +39 02 963911 - Fax +39 02 9650314 www.ditec.it - ditec@ditecva.com...
-
Page 2: Table Of Contents
INDEX Subject Page 1. General safety precautions 2. Declaration of incorporation of partly completed machinery 2.1 Machinery Directive 3. Technical specifications 3.1 Operating instructions Standard installation Examples applications Installation 6.1 Preliminary checks 6.2 Foundation case installation 6.3 Lever mechanisms installation 6.4 Wing release installation 6.5 Geared motor installation 6.6 Installation with CUBIC6L-CUBIC6LG... -
Page 3: General Safety Precautions
GENERAL SAFETY PRECAUTIONS This installation manual is intended for professionally competent personnel only. Installation, electrical connections and adjustments must be performed in accordance with Good Working Methods and in compliance with applicable regulations. Before installing the product, carefully read the instructions. Bad installation could be hazardous. -
Page 4: Declaration Of Incorporation Of Partly Completed Machinery
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY (Directive 2006/42/EC, Annex II-B) The manufacturer DITEC S.p.A. with headquarters in Via Mons. Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY declares that the automation system for CUBIC swing gates: has been constructed to be installed on a manual door to construct a machine pursuant to the Directive 2006/42/EC. -
Page 5: Technical Specifications
TECHNICAL DATA CUBIC6 CUBI6H CUBIC6HV Power supply 230 V~ 50 Hz 24 V 24 V Absorption 1,5 A 12 A 12 A Couple 340 Nm 340 Nm 220 Nm Capacitor 10 µF Opening time 18 s/90° 12÷25 s/90° 6÷13 s/90°... -
Page 6: Standard Installation
The connection to the mains must be made via an independent channel, separated from the connections to command and safety devices. nOTE: the given operating and performance features can only be guaranteed with the use of DITEC accessories and safety devices. -
Page 7: Examples Applications
Examples applications CUBIC6L - CUBIC6LG max 110° CUBIC6TC max 180° CUBIC6TIG max 180° IP1812EN • 2012-07-10... -
Page 8: Installation
INSTALLATION Unless otherwise specified, all measurements are expressed in millimetres (mm). 6.1 Preliminary checks Check that the structure is sufficiently sturdy and that the hinge pivots are properly lubricated. Provide an opening and closing stop. note: if the gate wing is more than 2.5 m wide, an electric lock should be installed. 6.2 Foundation case installation Install the foundation case as indicated in the relevant manual. -
Page 9: Installation With Cubic6L-Cubic6Lg
6.6 Installation with CUBIC6L-CUBIC6LG Insert lever [A] on the gearmotor and position the mechanical stop [B] and [C] and adjust it, as shown in the figure. NOTE: the figure shows the motor installed on the right door wing. 6.7 Installation with CUBIC6TC Insert pinion [A] and join the two pinions by means of the chain [B], as shown in the figure. -
Page 10: Installation With Cubic6Tig
6.8 Installation with CUBIC6TIG Fix the plate [A], then insert, fix and lubricate the gears [B], [C] and [D]. Position the sphere [E] as shown in the figure. 6.9 CUBIC6FM-CUBIC6FMTI installation It is possible to limit the travel of the wing by means of magnetic limit switches. Choose and install the magnetic limit switches as indicated in the relative manual. -
Page 11: Electrical Connections
WARNING: the electrical connections for the extension of the motor cables must be made on the outside of the foundation casing in an appropriate junction box (not supplied). In the CUBIC6 gearmotors, the blue wire corresponds to the common contact of the motor phases, and must be connected to the W or Z terminals of the control panel. -
Page 12: User Instructions
IP1812EN • 2012-07-10... -
Page 13: General Safety Precautions
CUBIC6 9. Operating instructions 9.1 General safety precautions The following precautions are an integral and essential part of the product and must be supplied to the user. Read them carefully since they contain important information on safe installation, use and maintenance. -
Page 14: Manual Release Instruction
WARnInG: the door wing block and release operations must be performed with the motor idle. Installer: DITEC S.p.A. Via Mons. Banfi, 3 21042 Caronno Pertusella (VA) - ITALY Tel. +39 02 963911 - Fax +39 02 9650314 www.ditec.it - ditec@ditecva.com IP1812EN • 2012-07-10... - Page 15 IP1812EN • 2012-07-10...
- Page 16 DITEC S.p.A. Via Mons. Banfi, 3 21042 Caronno P.lla (VA) Italy Tel. +39 02 963911 Fax +39 02 9650314 www.ditec.it ditec@ditecva.com DITEC BELGIUM LOKEREN Tel. +32 9 3560051 Fax +32 9 3560052 www.ditecbelgium.be DITEC DEUTSCHLAND OBERURSEL Tel. +49 6171 914150 Fax +49 6171 9141555 www.ditec-germany.de...