Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FAAC FSW900
Summary of Contents for FAAC FSW900
- Page 1 Swing Gate Operator UL325 - UL991 FAAC International Inc. FAAC International Inc. West Coast Operations Headquarter & East Coast Operations 357 South Acacia Avenue 5151 Sunbeam Road Unit 357 Suites 9-11 Fullerton, CA 92831 Jacksonville, FL 32257 Tel. (800) 221-8278...
-
Page 2: Table Of Contents
Read and follow all U.L. and Safety Standards before installing any access device. Please refer to this manual and qualified personnel for assistance. Do not install this device unless all entrapment and pinch points are eliminated! FSW900 Swing Gate Operator... -
Page 3: Important User Instructions
Proper reversing devices MUST be installed on all gates to avoid all potential hazards and entrapment. 9. SAVE THESE INSTRUCTIONS FSW900 Swing Gate Operator... -
Page 4: Important Safety Information
Fence Vehicular Gate Only Building Structure Provide spacing between the Fence hinge, gate and Mount hinges on building to the corner of reduce the risk of pilasters to help entrapment in prevent this area entrapment areas. FSW900 Swing Gate Operator... -
Page 5: Internal Entrapment Prevention
One or more Edge Sensors shall CAUTION: This beam only be located on the inside and Bottom Edge detects at the installed height. Sensor If Greater outside leading edge of the gate. Than 6 Inches FSW900 Swing Gate Operator... -
Page 6: Ul325 Gate Operator Classification
CONTACT SENSOR: External device such as a edge sensor used to provide entrapment prevention located where a risk of entrapment or obstruction exists such as the leading edge, trailing edge, and posts mounted inside and outside of the vehicular slide gate and motor. FSW900 Swing Gate Operator... -
Page 7: Warning Sign Installation
Select the proper gate operator for the installation. Consider the usage, capacity, gate size, gate weight, and needed features and safety accessories. If proper safety guidelines can not be followed do not install the gate operator. FSW900 Swing Gate Operator... -
Page 8: Manual Release
3. Press the Release Handle down until tight. The release handle should be tightened so the arm connector does not slip on the output shaft during gate operation 4. Attach the top arm cap cover. 5. Turn power on. Make sure the gate and all reversing devices are operating correctly. FSW900 Swing Gate Operator... -
Page 9: Technical Specification
Maximum Gate Weight ............. 800 lbs Maximum Gate Length .............. 18 Feet Primary Entrapment Protection ..........Inherent Current Sensor Secondary Entrapment Protection ..........Provisions for Non-Contact & Contact Sensors UL325 Class of Operation ............Class I, II, II, IV FSW900 Swing Gate Operator... -
Page 10: Gate Operator Installation
ONCRETE OCATION The FSW900 vehicular gate operator is designed to be mounted on a concrete pad. Select a location for the gate operator to be installed. For pad location and size: 1. Determine the location for the operator to be installed. Determine the location of the output shaft as described above. -
Page 11: Gate Operator Bolt Down
5. The Release Handle Nut Plate may be removed to adjust the Release Handle position if needed. Reconnect the plate when adjusted. 6. Attach the top Arm Cap Cover. FSW900 Swing Gate Operator... -
Page 12: Gate Operator Direction
4. Run the operator again and fine tune the Cam positions. Make sure each limit cam hits the switch cleanly TOP CAM: BOTTOM CAM: CLOSE for Left hand op. OPEN for Left hand op. OPEN for Right Hand op. CLOSE for Right Hand op. FSW900 Swing Gate Operator... -
Page 13: Lectrical Nstallation
3. Connect the AC input wires to the AC terminal located on the bottom/center of the control box. See diagram below. 4. Batteries must be installed after the AC power is on. See Battery Power Connection. GREEN = Ground WHITE = Neutral BLACK = Line FSW900 Swing Gate Operator... -
Page 14: Battery Power Connection
Additional 24 VDC for accessories may be found on the Radio Terminal, Edge/Photo Terminal, and External Loop Terminal. A connection between 24V DC+ and Common will supply power. FSW900 Swing Gate Operator... -
Page 15: Master/Slave Connection
Master Slave Gate Operator Gate Operator Master Slave Switch 3: Switch 3: 24 VDC WIRED Connection [GND[ to [GND] BROWN [TX+] to [RX+] GREEN [TX–] to [RX–] GREEN-WHITE [RX+] to [TX+] ORANGE [RX–] to [TX–] ORANGE-WHITE FSW900 Swing Gate Operator... -
Page 16: Ate Perator Djustments
4. Only resetting the operator will reactivate the gate and return it to normal operation. 5. To reset the operator in a Hard Shut Down situation: Press the reset button on the left side of the controller or turn the power switch OFF and back ON. FSW900 Swing Gate Operator... -
Page 17: Close Time Delay Adjustment
Delays 2 seconds before activating gate. Allows time for Maglock to discharge. OFF: No action - not used on FSW900 Tamper Detect Activates Tamper Detect Feature - not used on FSW900 OFF: Normal Soft Start, Soft Stop mode. Hard Start Operator starts with 40% motor power for more starting torque. -
Page 18: Accessory Connections
CCESSORY ONNECTIONS CCESSORY ONNECTIONS CCESSORY VERVIEW FIRE LOCK Card Access Phone Entry CLOSE Photo Cell Key Box OPEN STOP Photo Cell CLOSE Radio Receiver OPEN FSW900 Swing Gate Operator... -
Page 19: Edge Sensor Connections
Wireless contact sensors should be checked on a regular basis. Batteries should be replaced on a regular basis. Use only UL325 compliant devices and follow all installation guidelines set forth by the manufacturer. FSW900 Swing Gate Operator... -
Page 20: Photo Sensor Connections
Refer to the diagrams in the “Important Safety Information” section of this manual. CLOSE Photo Cell Use only UL325 compliant devices and follow all installation guidelines set forth by the manufacturer. FSW900 Swing Gate Operator... -
Page 21: Standard Reverse Connections
1. Allows external input to reset gate operator during a Hard Shutdown. External 2. Allows external input to reset operator settings during Reset installation. Connecting External Reset Devices: 1. Connect Reset Button to RESET and COMMON. FSW900 Swing Gate Operator... -
Page 22: Access Control Connection
This prevents the Fire Input from closing the gate if in the open position. Connecting Access Devices: 1. Connect Fire Lock Control relays to FIRE and COMMON. (Most devices use Normally Closed & Common) FSW900 Swing Gate Operator... -
Page 23: Radio Receiver Connections
2. If the Radio Receiver uses 24VDC, connect Radio Power to RADIO PWR +24VDC and RADIO PWR - 24VDC. Connecting FAAC XR2 Radio Receivers: 1. Connect XR2 N.O. relay contacts to RADIO N.O. and RADIO COMMON. 2. Connect XR2 Power + to RADIO PWR +24VDC and XR2 Power - to RADIO PWR -24VDC. -
Page 24: Alarm & Warning Light Connections
2. Connect the Solar Panel positive to SOLAR + 3. Connect the Solar Panel negative to SOLAR - 12VDC, 20 Watt Batteries should be tested regularly for proper battery backup operation. Batteries should be replaced each year or as needed. FSW900 Swing Gate Operator... -
Page 25: Loops & Loop Detectors
Seal the loop slots with a sealant. Make sure the sealant is 61’ to 240’ able to sink to the bottom of the loop slot and completely encase the loop wire. The wire should not move when the 241’ & Up sealant has set. FSW900 Swing Gate Operator... -
Page 26: Plug-In Loop Detector Connections
2. Shadow Loop: Connect relay wires to SHADOW N.O. and COMMON.. 3. Reverse Loop: Connect relay wires to REVERSE N.O. and COMMON. 4. Open Loop: Connect relay wires to OPEN N.O. and COMMON. 5. Set different frequencies for each loop detector. FSW900 Swing Gate Operator... -
Page 27: Troubleshooting Tips
3. Run a new CAT5 wire on top of the driveway to test the master slave communication. This will determine if the underground wire is good or bad. Possible damage to the control board master slave components. Have boards repaired FSW900 Swing Gate Operator... -
Page 28: Spare Parts
Controller Assembly (No PCB, faceplate) MOTOR-0500-24 Motor - 500W, 24VDC SW-0020 Gearbox 900:1 SW-0004 Weld arm connector with 12” bar SW-0003 Swing arm connector SW-0011 Clutch alignment pin SW-0010 Swing limit cam SW1000+ Limit assembly kit 3540 Battery (single) FSW900 Slide Gate Operator... - Page 29 PARE ARTS PARE ARTS FAAC p/n Description SW0003+ Clutch assembly kit SWITCH-0100 Limit switch WIRE1101SK Sensors wire assembly with screws AAA0450 Sensor cup assembly AAA-0402 Motor Adapter Plate SW-0200 Swing arm assembly FSW900 Slide Gate Operator...
-
Page 30: Imited Arranty
FAAC FAAC International, Inc. to be free from defects in material International, Inc. The warranty herein above set forth shall...