Advertisement
Table of Contents
- 1 General Safety Regulations
- 2 Electrical Set-Up
- 3 Description and Technical Specifications
- 4 Preliminary Checks
- 5 Mechanical Installation
- 6 Mounting the Rack
- 7 Electrical Connections
- 8 SIGNALLING Leds
- 9 Rotation Direction Check
- 10 Manual Operation
- 11 Return to Normal Operation
- 12 Maintenance
- Download this manual
Advertisement
Table of Contents
Related Manuals for FAAC 884 mct
Summary of Contents for FAAC 884 mct
- Page 1 884 MCT 884 MCT & 884 T & 884 T UNI EN ISO 9001-085...
-
Page 2: General Safety Regulations
6) FAAC S.p.A. cannot be held responsible for any damage caused by improper use or different from the use for which the automation system is destined to. -
Page 3: Electrical Set-Up
Table 1 Technical specifications 884 MCT Power supply 230V 3ph / 400V 3ph + N (+ 6 % - 10 %) 50Hz The FAAC model 884 automations for sliding gates are Power consumption (W) electromechanical operators which transmit movement to the Reduction ratio 1 : 43.2... -
Page 4: Mechanical Installation
ENGLISH ENGLISH • If the gear motor is located in a vehicle transit area, it is a good idea to provide protection against accidental collisions. • Check that the gear motor has an efficient earth connection. 4.2. INSTALLING THE BASE PLATE 1) The base plate must be positioned as shown in Fig. - Page 5 ENGLISH ENGLISH Fig. 12 START-UP 5.1. CONNECTION OF CONTROL BOARD Fig. 9 Important: Before attempting any work on the control board (connections, programming, maintenance), always turn off 4) Place another rack element next to the first and use a power. section of rack to set the teeth of the two elements in phase Observe points 10, 11, 12, 13 and 14 of the GENERAL SAFETY as shown in 11A.
-
Page 6: Electrical Connections
LED FCA LED: OPENING LIMIT-SWITCH RESET PUSH-BUTTON DECODER CONNECTOR LOW VOLTAGE TERMINAL BOARD FAAC LAMP CONNECTION TERMINAL BOARD MOTOR CONNECTION TERMINAL BOARD 3-PHASE POWER SUPPLY TERMINAL BOARD TRANSFORMER PRIMARY WINDING FUSE (F 5A) ACCESSORIES FUSE (T 1.6A) INDICATOR-LIGHT FREE CONTACT... -
Page 7: Signalling Leds
ENGLISH ENGLISH Uscita lampada spia (Warning Light) 24 Vac 5.2. DESCRIPTION Il carico massimo della lampada spia è di 5W. 5.2.1. J1 CONNECTOR For instructions on operation of the indicator-light, The J1 connector is used for rapid connection of cards consult microswitch programming. - Page 8 ENGLISH ENGLISH 5.3. PROGRAMMING TABLE 6 LOGIC A2 (AUTOMATICA PLUS) To program operation of the automated system, use the LOGIC A2 PULSES microswitches as shown below. GATE STATUS OPEN A - OPEN B (1) STOP SAFETY DEVICES CLOSED opens and re- no effect no effect closes after pause...
-
Page 9: Rotation Direction Check
ENGLISH ENGLISH TABLE 12 LOGIC C (DEAD-MAN) LOGIC C CONTROLS HELD DOWN PULSES The securing slot allows you to finely locate the limit-switch CONTINUOUSLY position. GATE STATUS OPEN A (5) OPEN B (4 and 5) SAFETY DEVICES STOP Important : a) The plate must activate the limit-switch on the CLOSED opens... -
Page 10: Manual Operation
- A safety microswitch in the release system prevents the automation from being activated by accidental commands 10. REPAIRS (7, fig. 2). For repairs contact an authorised FAAC Repair Centre. - Close the door and open or close the gate manually. - Page 11 DESCRIPTION The FAAC 884 automation is ideal for controlling industrial vehicle access areas. The 884 for sliding gates is an electromechanical operator which transmits movement to the leaf by means of a pinion with rack or chain coupled in an appropriate manner to the sliding gate.