Marley K404A Installation & Maintenance Instructions

Marley K404A Installation & Maintenance Instructions

K series (model a) fan forced wall heaters

Advertisement

"K" Series
(Model A)
Fan Forced
Wall Heaters
Installation & Maintenance Instructions
Dear Owner,
Congratulations! Thank you for purchasing this new heater manufactured by Marley Engineered
Products. You have made a wise investment selecting the highest quality product in the heating indus-
try. Please carefully read the installation and maintenance directions shown in this manual. You should
enjoy years of efficient heating comfort with this product from Marley Engineered Products... the indus-
try's leader in design, manufacturing, quality and service.
Read Carefully - These instructions are written to help you
prevent difficulties that might arise during installation of
heaters. Studying the instructions first may save you consid-
erable time and money later. Observe the following proce-
dures and cut your installation time to a minimum.
To reduce risk of fire or electric shock:
1. To prevent electrical shock, disconnect all power coming
to heater at main service panel before wiring or servicing.
2. All wiring must be in accordance with the National and
Local Electrical Codes and the heater must be grounded
as a precaution against possible electric shock.
3. Verify the power supply voltage coming to heater match-
es the ratings printed on the heater nameplate before
energizing.
4. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces.
WARNING
!
5. Do not insert or allow foreign objects to enter any ventila-
6. To prevent a possible fire, do not block air intakes or
7. A heater has hot and arcing (sparking) parts inside. Do
8. Use this heater only as described in this manual. Any
9. This heater is not approved for use in corrosive atmos-
SAVE THESE INSTRUCTIONS
1
(400mm)
15-3/4"
(485mm)
19-1/8"
FILE #E21609
... The Employees of
Marley Engineered Products
tion or exhaust opening as this may cause an electric
shock, fire, or damage to the heater.
exhaust in any manner. Keep combustible materials, such
as crates, drapes, etc., away from heater. Do not install
behind doors, furniture, towels, or boxes.
not use it in areas where gasoline, paint, or flammable
liquids are used or stored.
other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.
pheres such as marine, green house, or chemical storage
areas.
(95mm)
(35mm)
3-3/4"
1-3/8"
(463mm)
18-1/4"

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the K404A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Marley K404A

  • Page 1: Save These Instructions

    Products. You have made a wise investment selecting the highest quality product in the heating indus- try. Please carefully read the installation and maintenance directions shown in this manual. You should enjoy years of efficient heating comfort with this product from Marley Engineered Products... the indus- try’s leader in design, manufacturing, quality and service.
  • Page 2 IMPORTANT MIN. 36” (915mm) WARNING to ceiling 18-1/2” MIN. (470mm) DO NOT INSTALL HEATER UPSIDE DOWN OR SIDE- WAYS. DO NOT USE HEATER WITHOUT GRILLE. 8” MIN. CAUTION (203mm) 8” MIN. 14-1/2” MIN. (203mm) (362mm) CABLE CLAMP POWER SUPPLY CABLE GROUND SCREW FOR WALL MOUNTING ONLY.
  • Page 3 POWER 3-13/16" LEADS (97mm) THERMOSTAT GRILLE MOUNT BACK BOX TO WALL USING REAR 19" MOUNTING HOLES. (482mm) KNOB HANG FRAME ON BACK BOX 15-5/32" (385mm) Fig. 3: Surface Mounting Installation RECESS BACK Installation of Back Box With Optional Surface-Mounting Frame (See Figure 3). HEATER 1.
  • Page 4 AND DO NOT DISTURB THE HEATING ELEMENT. DOIT ÉTRE UTILISÉ AVEC BOÎTIER ARRIÈRE AWH-BB NE PAS UTILISER SI LE COUVERCLE AVANT NʼEST PAS EN PLACE. MARLEY ENGINEERED PRODUCTS 5. Turn on the main line switch (or replace fuses) to BENNETTSVILLE, SC 29512 4104-2093-028 restore power to the heater.
  • Page 5: Limited Warranty

    Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service center or the Marley Engineered Products Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley.

Table of Contents