Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CTC Union FRM220A
Summary of Contents for CTC Union FRM220A
- Page 1 FRM220A Hardware Installation...
- Page 3 FRM220A Hardware Installation Manual Fiber In-band Managed Media Platform Rack, 20 Slot, 2U with GbE Aggregate Switch Version 0.9d May 2011 (pre-Release) Copyright © 2007~2011, CTC Union Technologies, Inc. All rights reserved. All specifications are subject to change without prior notice.
- Page 4 CTC Union Technologies assumes no responsibility, however, for possible errors or omissions, or for any consequences resulting from the use of the information contained herein. CTC Union Technologies reserves the right to make changes in its products or product specifications with the intent to improve function or design at any time and without notice and is not required to update this documentation to reflect such changes.
-
Page 5: Table Of Contents
1.6 GSW/SNMP (Aggregate Switch)............................10 1.7 FRM220-1000EAS/X 802.3ah In-band managed Gigabit Fiber Media Converter............11 1.8 FRM220A-E1/ET100 E1 Inverse Multiplexer (Ethernet over E1) ..................12 1.9 FRM220A-EoE1 Ethernet Bridge (Ethernet over E1) ...................... 13 1.10 FRM220A-E1/Data Fractional E1 DSU/CSU Card ......................14 ... - Page 6 Table of Contents...
-
Page 7: Chapter 1 Introduction
L2 switch and interface cards are hot swappable allowing online field replacement. An additional feature allows FRM220A to detect the working or failing status either of power module or any fan assembly in the unit and activate relays that can be used to control external alarm devices. -
Page 8: Chassis Front Description
Chapter 1 Introduction 1.2 Chassis Front Description The front of FRM220A contains the line card slots. They are numbered 1 through 20, from left to right as viewed from the front. The typical configuration is with one GSW/SNMP (Network Management Controller) card in rear slot and in-band manageable line cards in any front slot numbered 1 through 20. -
Page 9: Chassis Physical Dimensions
Chapter 1 Introduction 1.4 Chassis Physical Dimensions Figure 1-3 Chassis Dimensions, in millimeters... -
Page 10: Chassis Specifications
1.6 GSW/SNMP (Aggregate Switch) FRM220A must be ordered with an aggregate Card. The card is placed in the rear of the chassis and provides backplane connection to each card slot. Management is accomplished either via Ethernet and any standard SNMP network management software that supports MIB-II. -
Page 11: Frm220-1000Eas/X 802.3Ah In-Band Managed Gigabit Fiber Media Converter
10/100/1000Base-TX and 1000Base-SX/LX with SFP-LC connector. With SNMP agent and GUI Web- based management in FRM220A, the Network administrator can monitor, configure and control the activity of each 802.3ah series line card. This 802.3ah OAM Compliant media converter, with its Q-in-Q and maximum interoperability will enable carriers and service provider to have a clear vision of their network and conveniently manage their demarcation point. -
Page 12: Frm220A-E1/Et100 E1 Inverse Multiplexer (Ethernet Over E1)
16E1/ET100 features diagnostic capabilities for performing remote loopback. The operator at either end of the line may test both the FRM220A-16E1/ET100 and the line in the digital loopback mode. The Ethernet copper interface supports auto-negotiation and auto MDI/MDIX, allowing plug-and-play Ethernet connection without any additional configuration. -
Page 13: Frm220A-Eoe1 Ethernet Bridge (Ethernet Over E1)
LANs over single E1 transports. The FRM220A-EoE1 transmits up to a 1.8Mbps Ethernet bridge channel (HDLC encapsulated) over 1 E1 link. The FRM220A-EoE1 supports an E1 attenuation of up to 43 dB on twisted pair or coax cable. This provides an approximate operating range up to 2km (using 22AWG). The FRM220A-EoE1 fully meets E1 specifications including ITU-T G.703 and G.823. -
Page 14: Frm220A-E1/Data Fractional E1 Dsu/Csu Card
Chapter 1 Introduction 1.10 FRM220A-E1/Data Fractional E1 DSU/CSU Card The FRM220A-E1/DATA slide in card DSU/CSU is a digital access unit for Unframed or Fractional E1 services. The FRM220A-E1/DATA data channel supports user-selectable transmission rates via randomly selected E1 timeslots, which provides integral multiples of 64kbps or 56kbps, up to a maximum 2.048Mbps (unframed), for a line attenuation of up to 43 dB on twisted pair or coax cable. -
Page 15: Chapter 2 Installation
Earth Ground) central office power. The AC outlet should be capable of furnishing 90 to 250 VAC. Refer to 2.4 Electrical Installation. Allow at least 10cm (4 inch) clearance at the front of FRM220A for the Fiber and other copper cables. -
Page 16: Fan Units Removal/Replacement
FRM220A Media Converter Line Card may be mounted in FRM220A-CH20 chassis or serve as a stand-alone units. When installing in FRM220-CH01 single slot chassis, the outer cover holds the line card. The unit then serves as a stand-alone media converter that can be linked to a line card in FRM220A-CH20 chassis. FRM220-CH01-AC(DC), single... -
Page 17: Electrical Installation
2.4 Electrical Installation With an AC power module, AC power is supplied to FRM220A through a standard IEC C14 3-prong receptacle, located on the rear of the module. Any national power cord with IEC C13 line plug may be used to connect AC power to the power module. -
Page 18: Power Modules Removal/Replacement
2.6 Power Modules Removal/Replacement The Power Supply Modules in FRM220A are available in three versions, one AC and two DC types. The universal AC version supports input voltages of 100 to 240 volts at frequencies of 47 to 63 Hertz. The DC version supports either a standard 36 to 75VDC or an optional 18 to 36VDC input voltage. -
Page 19: Installation
Cards designed specifically for FRM220A also connect to the L2 Gigabit Switch backplane. All converter cards are designed to be "hot" swappable, meaning FRM220A chassis need not be powered off in order to remove or replace a card. Removal and installation of converter cards with the rack chassis under power will not effect the operation of other converter cards. - Page 20 Chapter 2 Installation This page left blank intentionally.
-
Page 21: Chapter 3. Management Quick Start
3.1 Introduction The information here is only a brief introduction to the management interfaces and methodologies for managing FRM220A. For in-depth use of the management features of FRM220A, please refer to the FRM220A Aggregate Switch User Manual. 3.2 Management Methods... -
Page 22: Web Based Manager
Chapter 3 Management Quick Start 3.4 Web Based Manager FRM220A GSW/SNMP supports web based management. Use your favorite browser (Internet Explorer or Firefox) and connect to FRM220A GSW/SNMP by using the GSW/SNMP's IP address. Refer to FRM220A GSW/SNMP User Manual for details. -
Page 23: Element Management System (Ems)
Chapter 3 Management Quick Start 3.5 Element Management System (EMS) The objective of an Element Management System is to provide four major functions for telecommunication operators: Fault Management (FM) Performance Management (PM) Configuration Management (CM) Security Management (SM) CTC Union's EMS is a proprietary management system designed to provision, monitor and maintain multiple equipments designed by CTC Union.