CTC Union FIB1-1000ES Installation Instructions

Installation Instructions

FIB1-1000ES 10/100/1000BASE-T
to 1000BASE-X
Managed Fiber Media Converter
Description
The Fiber Transceiver Converter Series gives you the option to choose from most popular fiber cabling
connectors. The FIB1-1000ES provides you with two versions which support SFP socket with LC type
connectors for your fiber optic cables and an RJ-45 connector for 10/100/1000Base-T twisted pair
cable connection. For the UTP side, auto-negotiation is default. These units will automatically tailor
themselves to 10/100/1000Base-T and both half-duplex or full-duplex signals depending on your
specific network needs. FX side is fixed in full-duplex only. The Fiber Transceiver Converters give you
the freedom to extend your 1000Mbps cabling distance by allowing connectivity up to 0.5Km in
multi-mode or 80Km in single mode. Six LED indicators signal the power status of the converter,
UTP port, speed, Link/RX, status of duplex, fiber port Link/RX and LLF (Link-Loss Forwarding).
DC Jack
DIP Switch Setting
DIP Function
Sw1~Sw3 UTP Mode
Sw4 Loop Back Test(LBT)
Jumpers Setting (on PCB)
LLF Function : On means enable, off means disable the function of LLF
ON OFF
State Status
Off Off Off UTP/NWAY
On Off Off 1000/Full
Off On Off 100/Full
Off On On 100/Half
On On Off 10/Full
On On On 10/Half
Off LBT off
On LBT on
( Link Loss Forwarding Function, detail please check Page2 )
Specifications
Standard
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T, IEEE802.3z 1000Base-X,
Gigabit Standards. Supports Full Duplex Ethernet mode (2000Mbps)
10/100/1000BASE-T RJ-45 Connectors
One RJ-45 connector is provided for connection to either MDI-X (To PC) or MDI (To HUB) equipment.
Utilizing Auto MDI/MDIX allows all UTP connections to be made using only a common straight-through
UTP cable.
RJ-45 Pin
5
4
3
6
1
2
7
8
Environment
Temperature : 0°C – 50°C
Humidity: 10-90% non condensing
Fiber
Connections
LEDs

LED Indicators

Ethernet
Connections
DIP LED
Switches
PWR
FX
LLF
Speed
Full
TX
1000BASE-T UTP Cable
568-A type 568-B type
Cable type: 1000Base-T; 4 pair , Cat. 5,
Pair1-Tip Pair1-Tip
EIA/TIA-568, STP/UTP
Pari1-Ring Pair1-Ring
Maximum cable distance: 100 meters
Pair2-Tip Pair3-Tip
(328 feet)
Pair2-Ring Pair3-Ring
Pair3-Tip Pair2-Tip
Fiber Optic Connectors
Pair3-Ring- Pair2-Ring
Pair4-Tip Pair4-Tip
SFP socket with LC is provided
Pair4-Ring Pair4-Ring
Power
AC adaptor +12V / 1A
Speed
FULL
Function State
Power indicatorOn On
Off
Fiber link On
Off
Blinking
Link Loss Forwarding On
Off
Mode display Yellow
Green
Off
Mode display On
Off
Ethernet link On
Off
Blinking
Dimension
122.6mm x 85.6mm x 20mm
( W x D x H )
PWR
LLF
TX FX
Status
Converter has power.
Converter has no power.
The fiber link is ok.
No link or the link is faulty.
Receiving data on the fiber.
Link loss forwarding function enable.
Link loss forwarding function disable.
Force the LAN speed in 1000Base.
Force the LAN speed in 100Base.
Force the LAN speed in 10Base.
Full duplex mode.
Half duplex mode.
The UTP link is ok.
No link or the link is faulty.
Receiving data on Ethernet.
V.: 1.1