STIEBEL ELTRON SBB 300 plus Operation & Installation
  1. Manuals
  2. Brands
  3. STIEBEL ELTRON Manuals
  4. Water Heater
  5. SBB 300 PLUS
  6. Operation & installation
STIEBEL ELTRON SBB 300 plus Operation & Installation

STIEBEL ELTRON SBB 300 plus Operation & Installation

Stiebel eltron hot water heaters operation & installation
Hide thumbs Also See for SBB 300 plus:
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents

See also: Operating and Installation Instruction
SBB 300 plus, SBB 400 plus, SBB 600 plus
Operation & Installation
Index
Instruction Manual
1
Operation and Service
1.1 Start-Up
2
Maintenance and Cleaning
2.1 Pressure Relief Valve
2.2 Decalcification
2.3 Sacrificial Anode – Inspection /
Replacement
3
Failures – Cause – Correction
4
Technical Specifications
4.1 Technical Data
4.2 Dimensions
Installation Instructions
5
General
5.1 Description
5.2 Delivery Configuaration
5.3 Regulations and standards
5.4 Set-up and operation
6
Set-up and installation
6.1 Set-up
6.2 Connection
6.3 Heater Installation
6.4 Hot water Installation
6.5 Hot Water Temperature Probe
6.6 Solar Temperature Probe
6.7 Connection to the Solar Unit
6.8 Sacrificial Anode

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SBB 300 plus and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for STIEBEL ELTRON SBB 300 plus

Summary of Contents for STIEBEL ELTRON SBB 300 plus

  • Page 1 SBB 300 plus, SBB 400 plus, SBB 600 plus Operation & Installation Index Instruction Manual Operation and Service 1.1 Start-Up Maintenance and Cleaning 2.1 Pressure Relief Valve 2.2 Decalcification 2.3 Sacrificial Anode – Inspection / Replacement Failures – Cause – Correction Technical Specifications 4.1 Technical Data...
  • Page 2 Important Tip Stiebel Eltron hot water heaters should only be installed or serviced by licensed installers. These are not do-it-yourself appliances. Please hand this Operation and Installation Manual and hand over to the home or building owner when the installation is complete.

  • Page 3: Technical Specifications

    16 Warm water outlet / T & P relief valve location 17 Cold water inlet (SBB 600) 18 Circulation port Diag. 1. 4.1 Technical Data Type SBB 300 plus SBB 400 plus SBB 600 plus Contents Storage capacity Gal / ltr 80.6 / 305...
  • Page 4 Dimensions Diag. 2. 4.2 Dimensions Type SBB 300 plus SBB 400 plus SBB 600 plus Height of unit w/insulation in./mm 66.1/1679 72.7/1848 68.3/1735 Height of unit without insulation in./mm 63.3/1609 70.1/1781 65.7/1670 Height of well for temp. sensor in./mm 46.4/1179 48.7/1238...
  • Page 5 Diagram 1 is referenced for explanation of the following text. 5.1 Brief Description of the Appliance 5.1.1 Application The Stiebel Eltron Vertical Solar Storage tank SBB … Plus, in combination with Stiebel Eltron’s Solar Collector is an economical hot water generator. 5.1.2 Connections All connections (cold and hot) are readily accessible and allow for easy installation.

  • Page 6: Setup And Installation

    6. Set-up and Installation 6.1 Set-up Inspect the packaging for damage and remove packaging at the installation site. Verify presence of six brass thread to sweat fittings. The installation site must be structurally capable of supporting the weight of the tank when filled. The location has to be above freezing.

  • Page 7: System Diagram

    Installation Diagram Solar storage tank SBB plus to Hydronic back-up Boiler T & P valve Boiler filler and drainage faucet Heating loop circulator Pressure expansion tank Check valve Drainage faucet for the tank Check valve Shut-off valve 10 Cold water pipe 11 SBB plus storage tank 12 Hot water pipe 13 T &...
  • Page 8 6.5 Hot water temperature probe 6.5.1 The hot water temperature probe is to be installed into the upper immersions sleeve (Pos. 3 Diagram1). 6.6 Solar Storage Tank – Temperature Probe The solar storage tank temperature probe to lower immersion sleeve of the hot water storage tank (Pos. 6 Diagram 1). The temperature probe must be completely inserted into the probe sleeve.
  • Page 9 To obtain service under this warranty, the owner must first secure written authorization from Stiebel Eltron, Inc. The owner shall be required to show proof of purchase date, and to pay all transportation costs to return the defective part(s) for repair or replacement.

Table of Contents