Table of Contents
Advertisement
Quick Links
BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
UTILISATION ET INSTALLATION
BEDIENING EN INSTALLATIE
USO E INSTALLAZIONE
OB SLUHA A INSTALACE
Warmwasser-Standspeicher | Floorstanding DH W cylinder | Ballon ECS sur pied |
Staande warmwaterboiler | Acqua calda - Caldaia verticale | Stacionární zásobník
teplé vody
» SBB 600 WP SOL
» SBB 800 WP SOL
» SBB 1000 WP SOL
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for STIEBEL ELTRON SBB 600 WP SOL
Summary of Contents for STIEBEL ELTRON SBB 600 WP SOL
- Page 1 Warmwasser-Standspeicher | Floorstanding DH W cylinder | Ballon ECS sur pied | Staande warmwaterboiler | Acqua calda - Caldaia verticale | Stacionární zásobník teplé vody » SBB 600 WP SOL » SBB 800 WP SOL » SBB 1000 WP SOL...
-
Page 2: Table Of Contents
CONTENTS | OPERATION GENERAL INfORMATION OPERATION OPERATION General information ��������������������������������������� 14 Safety instructions ���������������������������������������������� 14 Other symbols in this documentation ���������������������� 15 General information Units of measurement ����������������������������������������� 15 Safety �������������������������������������������������������� 15 The chapter "Operation" is intended for appliance users and heat- Intended use �����������������������������������������������������... -
Page 3: Operation
OPERATION SAfETY Safety Other symbols in this documentation Note Intended use General information is identified by the symbol shown The appliance is intended for heating and storing domestic hot on the left. water when operating a heat pump with a higher or a high out- f Read these texts carefully. -
Page 4: Cleaning, Care And Maintenance
OPERATION | INSTALLATION CLEANING, CARE AND MAINTENANCE INSTALLATION Cleaning, care and maintenance f Have a contractor regularly check the appliance, the safety assembly and all fitted accessories. f Never use abrasive or corrosive cleaning agents. A damp Safety cloth is sufficient for cleaning all plastic parts. Only a qualified contractor should carry out installation, commis- Signal anode consumption indicator sioning, maintenance and repair of the appliance. -
Page 5: Preparations
For this, ensure that there is enough space for the Minimum clearances installation task. You can then link the appliance into the heating and DHW system. SBB 600 WP SOL: 9.2.2 Fitting the signal anode Material losses When operating the cylinder without consumption indica- tor, leave the plug in the fitting. -
Page 6: Heating Or Solar Installation
INSTALLATION INSTALLATION Heating or solar installation Water connection and safety assembly f Prior to connecting the heating water lines or the solar ther- 9.2.1 Safety instructions mal system, flush the indirect coils with water. f You may connect both indirect coils to the "heat pump return" Note and "solar flow"... -
Page 7: Commissioning
INSTALLATION COMMISSIONING 10. Commissioning 13. Maintenance 10.1 Initial commissioning WARNING Electrocution Carry out all electrical connection and installation work f Open a draw-off point until the appliance has filled up and in accordance with relevant regulations. the pipework is free of air. f Adjust the flow rate. -
Page 8: Specification
INSTALLATION SPECIfICATION 14. Specification 14.1 Dimensions and connections SBB 600 WP SOL SBB 600 WP Cold water inlet Male thread G 1 ¼ A DHW outlet Male thread G 1 ¼ A DHW circulation Male thread G ½ A Heat pump flow Female thread G 1 ½... - Page 9 INSTALLATION SPECIfICATION SBB 800 WP SOL 1010 SBB 800 WP SOL Cold water inlet Male thread G 2 A DHW outlet Male thread G 2 A DHW circulation Male thread G 1 A Heat pump flow Female thread G 1 ½ Heat pump return Female thread G 1 ½...
- Page 10 INSTALLATION SPECIfICATION SBB 1000 WP SOL 1010 SBB 1000 WP SOL Cold water inlet Male thread G 2 A DHW outlet Male thread G 2 A DHW circulation Male thread G 1 A Heat pump flow Female thread G 1 ½ Heat pump return Female thread G 1 ½...
-
Page 11: Fault Conditions
In the event of a fault, temperatures of up to 95 °C at 1.0 MPa can occur depending on the type of heat sources used. 14.3 Data table SBB 600 WP SOL SBB 800 WP SOL SBB 1000 WP SOL 235906... - Page 12 Deutschland Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de STIEBEL ELTRON GmbH & Co. KG Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | kundendienst@stiebel-eltron.de Dr.-Stiebel-Straße 33 | 37603 Holzminden Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | ersatzteile@stiebel-eltron.de Tel.
Need help?
Do you have a question about the SBB 600 WP SOL and is the answer not in the manual?
Questions and answers