Table of Contents
Related Manuals for Hotsy DA-232336 P COMET
Summary of Contents for Hotsy DA-232336 P COMET
- Page 1 OPERATOR’S MANUAL MODEL # ORDER # DA-232336 P COMET 1.107-097.0 DA-232337 P LEGACY 1.107-098.0 DA-252739 1.107-100.0 To locate your local Hotsy Commercial Pressure Washer Dealer nearest you, visit www.hotsy.com 8.780-015.0...
-
Page 2: Table Of Contents
CONTENTS Important Safety Information ..............4-6 Component Identification ................. 7 Assembly Instructions ................8 Operating Instructions.................9-10 Detergent and General Operating Techniques ........11 Shut Down and Clean-Up ..............12 Storage ....................12 Troubleshooting ................13-14 Preventive Manteinance ................ 15 Oil Change Record ................17 Warranty Model Number ______________________________ Serial Number ______________________________... -
Page 3: Important Safety Information
INTRODUCTION & IMPORTANT SAfETY INfORMATION Thank you for purchasing this Pressure Washer. WARNING: This machine ex- WARNING ceeds 85 db appropriate ear We reserve the right to make changes at any time protection must be worn. without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings... -
Page 4: Important Safety Information
IMPORTANT SAfETY INfORMATION Gasoline engines on mobile or portable equipment WARNING: Grip cleaning wand WARNING shall be refueled: securely with both hands before starting. Failure to do this could a. outdoors; result in injury from a whipping b. with the engine on the equipment stopped; wand. - Page 5 IMPORTANT SAfETY INfORMATION WARNING: Be extremely careful WARNING when using a ladder, scaffolding or any other relatively unstable location. The cleaning area should have adequate slopes and drainage to reduce the pos- sibility of a fall due to slippery RISK Of INjURY fROM fALLS WHEN USING surfaces.
-
Page 6: Component Identification
COMPONENT IDENTIfICATION Hose Detergent quick Coupler COMET G SERIES Detergent PUMP PUMP Injector Unloader quick Twist Coupler Hose Pressure Detergent Nozzle AxIAL PUMP Pump Protector Pump Spray Gun Detergent Inlet bucket Screen (not included) Garden Hose (not included) Straight Through Wand Trigger ENGINE 160cc (5.0HP) -
Page 7: Assembly Instructions
ASSEMbLY INSTRUCTIONS Gun & Alignment Hose Holes Knob Hanger Handle bolt frame Assy. STEP 1: Attach the handle to the STEP 2: Insert the carriage bolt STEP 3: Attach the Gun & hose frame of the pressure washer. Note: through the holes from the back of hanger and insert nuts from inside. -
Page 8: Operating Instructions
OPERATING INSTRUCTIONS Dipstick Oil Dipstick Oil Window STEP 1: Check engine oil level. Oil level should be level with the bottom STEP 2: Remove shipping cap of the oil filler neck. Be sure the machine is level when checking the oil and install oil dipstick. - Page 9 OPERATING INSTRUCTIONS On-Off Switch STEP 8: Turn the engine switch to "On" position. STEP 9: Pull the starter grip. If the engine fails to start after 2 pulls, squeeze the trigger gun to release pres- On Briggs engines, move the throttle lever to "Fast" sure and repeat step.
-
Page 10: Cleaning Tips
DETERGENT AND GENERAL CLEANING TECHNIqUES THERMAL PUMP PROTECTION WARNING: Some detergents WARNING may be harmful if inhaled or If you run the engine on your pressure washer for 1-2 ingested, causing severe nau- minutes without pressing the trigger on the spray gun, sea, fainting or poisoning. -
Page 11: Storage
SHUTTING DOWN AND CLEAN-UP On-Off Switch STEP 1: Remove detergent suc- STEP 2: Turn off the engine. STEP 3: Turn off water tion tube from container and insert supply. into one gallon of fresh water. Slide nozzle forward for low pressure or to connect black detergent nozzle. -
Page 12: Troubleshooting
TROUbLESHOOTING PRObLEM POSSIbLE CAUSE SOLUTION LOW OPERATING Insufficient water supply. Closed Use larger garden hose; clean inlet water PRESSURE faucet. Inlet hose kinked screen. Open faucet. Clogged inlet hose strainer Check plumbing system for leaks. Retape leaks with teflon tape. Faulty or mis-adjusted unloader Adjust unloader for proper pressure. - Page 13 TROUbLESHOOTING PRObLEM POSSIbLE CAUSE SOLUTION ENGINE OPERATES Not enough gas or engine oil Fill tank with gas. Check oil level. fOR 15 MINUTES Vapor lock developed by heat of day Keep gas tank full to avoid vapor locking. THEN STOPS Obstruction in fuel filter Clean or replace fuel filter.
-
Page 14: Preventative Maintenance
PREvENTATIvE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventa- tive maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. -
Page 15: Oil Change Record
OIL CHANGE RECORD Check pump oil and engine oil level before first use of your new pressure washer. Estimated Operating Estimated Operating Date Oil Changed Hours Since Last Date Oil Changed Hours Since Last Month/Day/Year Oil Change Month/Day/Year Oil Change 8.780-015.0 •... - Page 16 Hotsy does not authorize any other party, including authorized Hotsy Distributors, to make any representation or promise on behalf of Hotsy, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of Hotsy products conforms to local codes.
- Page 17 If you are looking for replacement parts for your Hotsy, please contact your local dealer. You can find a dealer by calling Hotsy at 800-525-1976 or by visiting www.hotsy.com.
- Page 18 Form #8.780-015.0 • DA • Revised 10/09 • Printed in U.S.A. or Mexico...