Hotsy 560SS Operating Instructions And Parts Manual
  1. Manuals
  2. Brands
  3. Hotsy Manuals
  4. Pressure Washer
  5. 560SS
  6. Operating instructions and parts manual

Hotsy 560SS Operating Instructions And Parts Manual

Hide thumbs Also See for 560SS:
Table of Contents

Advertisement

Quick Links

Read instructions carefully before attempting to assemble, install, operate or service this pressure
washer. Failure to comply with instructions could result in personal injury and/or property damage!
●
●
●
●
●
●
●
●
●
●
®
Output specifi cations are based on engine power curves at 100 meters
above sea level and 25
SAE J1349.
SERIAL NUMBER:
DATE PURCHASED:
FOR SALES AND SERVICE, PLEASE CONTACT:

SPECIFICATIONS

Pump Volume At Pump Head: 2.3 GPM/138 GPH
Pump Pressure At Pump Head: 1500 PSI
Burner Type: Fuel Oil Fired, 214,300 BTU/Hr.
Burner Fuel Pressure: 150 PSI
Machine Voltage: 115VAC/60Hz/1Ph
Total Machine Amperage: 20 Amps
Machine Weight: 310 Lbs.
Shipping Weight: 370 Lbs.
Exhaust Stack Size: 8"
Machine Dimensions: Length = 42", Width = 30", Height = 49"
o
C ambient temperature in accordance with
MODEL 560SS

OPERATING INSTRUCTIONS

AND PARTS MANUAL
c
®
8.914-357.0

Advertisement

Table of Contents
loading

Related Manuals for Hotsy 560SS

Summary of Contents for Hotsy 560SS

  • Page 1: Operating Instructions

    MODEL 560SS OPERATING INSTRUCTIONS AND PARTS MANUAL Read instructions carefully before attempting to assemble, install, operate or service this pressure washer. Failure to comply with instructions could result in personal injury and/or property damage! SPECIFICATIONS ● Pump Volume At Pump Head: 2.3 GPM/138 GPH ●...

  • Page 2: Table Of Contents

    The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 3: Important Safety Information

    9. Never run pump dry or leave spray gun closed phase this product should only be connected to a longer than 1-2 minutes. power supply receptacle protected by a GFCI. 10. Keep operating area clear of all persons. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 4: Important Safety Information

    TRIGGER GUN KICKS Keep good footing and balance at all times. 14. Be certain all quick coupler BACK - HOLD WITH fittings are secured before BOTH HANDS using pressure washer. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 5: Important Safety Information

    IMPORTANT SAFETY INFORMATION 21. Do not operate this machine when fatigued or under the infl uence of alcohol, prescription medications, or drugs. Follow the maintenance instructions specifi ed in the manual. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 6: Component Identifi Cation

    High Pressure Hose — Connect one end to water pump high pressure discharge nipple and the other end to spray gun. Unloader Valve — Safety device which, when the spray gun closes, prevents over pressurization. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 7: Assembly & Installation Instructions

    When selecting the location for installation, beware of poorly ventilated locations or areas where exhaust fans may cause an insuffi cient supply of oxygen. Proper combustion can only be obtained when there is a suf- 8.914-357.0 • HOTSY 560SS • Rev. 03/11...
  • Page 8 #1 or #2 smoke spot on the Bacharach scale. For additional burner component information, see Burner Assembly. It is recommended that the oil burner be serviced yearly or as needed. Contact your local service center. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 9: Operation Instructions

    60 angle to the work. This will allow the water to splash away from you and the water will wash the dirt away faster and easier. Figure 4 - Nozzle Installation/Manual Trigger Lock 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 10: General Cleaning Techniques

    • Ammonia products from dripping onto a rinsed area. For the best results, • Acid-based products contact your Hotsy dealer to help you select the best These chemicals will harm the machine and will detergent for your application. damage the surface being cleaned.

  • Page 11: Storage & Maintenance

    These deposits will Figure 6 - Pump Lubrication insulate the coil. This will restrict the air fl ow through the coil, further aggravating the soot buildup. Contact your local service center when desooting is needed. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 12: Troubleshooting

    Pump motor must be running before burner will light. Inadequate water supply. Fully open faucet. Check for kinked or dam- aged hose. Use 5/8 inch mini-mum hose. Check for debris clogging inlet screen. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...

  • Page 13: Troubleshooting

    If the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identifi ed by visiting www.hotsy.com or by calling 1-800-525-1976. 8.914-357.0 • HOTSY 560SS • Rev. 03/11...
  • Page 14 Hotsy does not authorize any other party, including authorized Hotsy Distributors, to make any representation or promise on behalf of Hotsy, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of Hotsy products conforms to local codes.
  • Page 15 If you are looking for replacement parts for your Hotsy, please contact your local dealer. You can find a dealer by calling Hotsy at 800-525-1976 or by visiting www.hotsy.com.
  • Page 16 Form # 8.914-357.0 • Revised 03/11 • Printed in U.S.A. by Hotsy...

Table of Contents