Activating The Surround Modes; Activating The Ex/Es Setting; Activating The Surroung Modes - JVC RX-7030VBK Instructions Manual

Activating the Surround Modes

Available Surround modes vary depending on the speaker settings
and the incoming signals. (See page 36.)
Activating one of the Surround modes for a source automatically
recalls the memorized settings and adjustments (see pages 25 to
33.)
You can also use the buttons on the remote control for the same
functions.

Activating the EX/ES setting

For multi-channel digital software, you can activate the EX/ES (7.1-
channel) reproduction mode.
• Once you have set EX/ES (7.1-channel) reproduction mode, it is
stored in memory and will be called up whenever you activate the
Surround mode which the memorized EX/ES (7.1-channel)
reproduction mode can be applied to.
Press EX/ES to select an appropriate setting for your enjoyment.
The currently selected EX/ES (7.1-channel) reproduction mode
appears on the display.
• Each time you press the button, it changes as follows:
EX/ES AUTO*: According to the incoming signal, an
appropriate Surround mode is applied.
• For Dolby Digital EX and DTS-ES,
EX/ES (7.1-channel) reproduction is
applied.
• For 5.1-channel (or less) encoded
software, 5.1-channel reproduction is
applied.
EX/ES ON*: Select to apply EX/ES (7.1-channel)
reproduction to both 5.1-channel and 6.1-
channel encoded software.
EX/ES OFF: Select to cancel the EX/ES (7.1-channel)
reproduction.
* If the surround back speakers are not connected or deactivated,
Virtual 6.1-channel surround is applied.
Notes:
• When Surround mode is deactivated, pressing EX/ES will
activate an appropriate Surround mode for the current source.
• When an analog or digital 2-channel source is playing, you can
adjust the EX/ES (7.1-channel) reproduction mode and store
the setting, but it will not affect the current source.
• When the source is one to which the EX/ES (7.1-channel)
reproduction cannot be applied, you can adjust the setting and
store in memory, but reproduction channels will remain
unchanged.
Activating the Surround Modes
1. Select and play any source other than "DVD
MULTI."
• Make sure you have selected the analog or digital input mode.
• Surround modes are not valid for DVD MULTI playback
mode.
2. Press SURROUND to activate the Surround
mode.
• For multi-channel digital software (except 2-channel and
Dual Mono software), incoming signals are automatically
detected and the appropriate surround mode is activated (see
page 36 for details).
DIGITAL AUTO
L C R LINEAR PCM
SUBWFR LFE DIGITAL
LS RS
Ex. When "DOLBY D" is activated.
– If the EX/ES (7.1-channel) reproduction mode has been set
to "AUTO" or "ON," one of the EX/ES (7.1-channel)
reproduction modes will be activated (see the left column).
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, Surround modes change as follows:
ANALOG
L R LINEAR PCM
SUBWFR
PL MOVIE PL
II
NEO:6MUSIC
• For Dual Mono software, you can select the channel you
listen to. (See page 29.)
DUAL DIGITAL AUTO
L
LINEAR PCM
SUBWFR DIGITAL
To adjust the speaker output level, see pages 32 and 33.
To cancel the Surround mode
Press SURROUND/DSP OFF (or SURR/DSP OFF on the remote
control). "SURR OFF" appears on the display.
SPEAKERS 1
VOLUME
PRO LOGIC
SPEAKERS 1
VOLUME
MUSIC PRO LOGIC
II
NEO:6CINMA
SPEAKERS 1
VOLUME
37