Mitsubishi Electric FR-F720-00046 Instruction Manual page 202

(5) Selection of command source in Network operation mode (Pr. 338, Pr. 339)
⋅
There are two control sources: operation command source, which controls the signals related to the inverter start
command and function selection, and speed command source, which controls signals related to frequency setting.
⋅ In Network operation mode, the commands from the external terminals and communication (RS-485 terminals or
communication option) are as listed below.
Operation Pr. 338 Communication operation command source
Location
Pr. 339 Communication speed command source 0: NET
Selection
Running frequency from communication
Fixed function
Terminal 2
(Terminal-
equivalent
Terminal 4
function)
Terminal 1
Low speed operation command/
0 RL
remote setting clear
Middle-speed operation command/
1 RM
remote setting deceleration
High speed operation command/
2 RH
remote setting acceleration
3 RT Second function selection
4 AU Terminal 4 input selection
5 JOG Jog operation selection
Selection of automatic restart after
6 CS
instantaneous power failure
7 OH External thermal relay input
8 REX Fifteen speed selection
10 X10 Inverter operation enable signal
FR-HC or MT-HC connection,
11 X11
instantaneous power failure detection
12 X12 PU operation external interlock
External DC injection brake
13 X13
operation is started
14 X14 PID control valid terminal
16 X16 PU-external operation switchover
Output stop
24 MRS
PU operation interlock
25 STOP Start self-holding selection
60 STF Forward rotation command
61 STR Reverse rotation command
62 RES Reset
63 PTC PTC thermistor input
64 X64 PID forward action switchover
65 X65 PU-NET operation switchover
66 X66 External-NET operation switchover
67 X67 Command source switchover
70 X70
DC feeding operation permission
71 X71
DC feeding cancel
72 X72
PID integral value reset
[Explanation of table]
External : Command only from control terminal signal is valid.
NET : Command only from communication is valid
Combined : Command from either of external terminal and communication is valid.
⎯
: Command from either of external terminal and communication is invalid.
Compensation : Command by signal from external terminal is only valid when Pr. 28 Multi-speed input compensation selection = "1"
REMARKS
⋅ The command source of communication is as set in Pr. 550 and Pr. 551.
⋅ The Pr. 338 and Pr. 339 settings can be changed while the inverter is running when Pr. 77 = "2". Note that the setting change is
reflected after the inverter has stopped. Until the inverter has stopped, communication operation command source and
communication speed command source before the setting change are valid.
Selection of operation mode and
0: NET
1:External 2:External 0: NET
⎯
NET NET NET
⎯ ⎯ ⎯
External
⎯ ⎯
External
Compensation
NET External NET
NET External NET
NET External NET
NET
⎯ ⎯
Combined
⎯
External
External
NET External NET
External
External
External
NET
NET External NET
External
Combined
External
⎯
NET
NET
External
External
NET External NET
External
External
External
NET
NET
NET External NET
operation location
1: External
Remarks
1:External 2:External
⎯
NET
⎯
External
External
External
Pr. 59 = "0" (multi-
speeds)
External
Pr. 59 = "1 , 2"
(remote)
External
External
Combined
External
Pr. 59 = "0"
External
(multi-speeds)
External
External
≠
External
Pr. 79
Pr. 79 = "7"
When X12 signal
is not assigned
External
External
External
External
External
External
External
"7"
4
193