Mitsubishi Electric FR-F720-00046 Instruction Manual page 126

Signal
Setting
Name
Pr. 59 = 0 (initial value)
2 RH
Pr. 59 ≠ 0
3 RT Second function selection
4 AU Terminal 4 input selection
5 JOG Jog operation selection
Selection of automatic restart after instantaneous power failure,
flying start
6 CS
Electronic bypass function
7 OH External thermal relay input
8 REX 15 speed selection (combination with three speeds RL, RM, RH)
10 X10 Inverter operation enable signal (FR-HC, MT-HC/FR-CV connection)
11 X11 FR-HC or MT-HC connection, instantaneous power failure detection
12 X12 PU operation external interlock
13 X13 External DC injection brake operation start
14 X14 PID control valid terminal
PU-external operation switchover
16 X16
(external operation when X16 turns on)
Output stop
24 MRS
Electronic bypass function
25 STOP Start self-holding selection
Forward rotation command
60 STF
(assigned to STF terminal (Pr. 178) only)
Reverse rotation command
61 STR
(assigned to STR terminal (Pr. 179) only)
62 RES Inverter reset
63 PTC PTC thermistor input (assigned to AU terminal (Pr. 184) only)
64 X64 PID forward/reverse action switchover
PU-NET operation switchover
65 X65
(PU operation when X65 turns on)
External-NET operation switchover
66 X66
(NET operation when X66 turns on)
Command source switchover
67 X67
(Pr.338 and Pr.339 commands are valid when X67 turns on)
70 X70 DC feeding operation permission
71 X71 DC feeding cancel
72 X72 PID integral value reset
⎯
9999 No function
When Pr. 59 Remote function selection ≠ "0", the functions of the RL, RM and RH signals change as listed above.
*1
*2 The OH signal turns on when the relay contact "opens".
REMARKS
⋅ Same function can be assigned to two or more terminals. In this case, the logic of terminal input is OR.
⋅ The priorities of the speed commands are in order of jog > multi-speed setting (RH, RM, RL, REX) > PID (X14).
⋅ When the X10 signal (FR-HC, MT-HC, FR-CV connection - inverter operation enable signal) is not set or when the PU
operation external interlock (X12) signal is not assigned at the Pr. 79 Operation mode selection setting of "7", the MRS signal
shares this function.
⋅ Same signal is used to assign multi-speeds (7 speeds) and remote setting. They cannot be set individually.
(Same signal is used since multi-speed (7 speeds) setting and remote setting are not used to set speed at the same time .)
CAUTION
⋅ Changing the terminal assignment using Pr. 178 to Pr. 189 (input terminal function selection) may affect the other functions. Also
check that wiring is correct, since the terminal name and the signal function became different. Please make setting after
confirming the function of each terminal.
Function
High-speed operation command
Remote setting (acceleration)
*1
*2
Function assignment of external
terminal and control
Related Parameters
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr.
232 to Pr. 239
Pr. 59
Pr. 44 to Pr. 51
Pr. 267
Pr. 15, Pr. 16
Pr. 57, Pr. 58, Pr.162 to Pr.165,
Pr. 299, Pr. 611
Pr. 57, Pr. 58 Pr. 135 to Pr. 139,
Pr. 159
Pr. 9
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27,
Pr.232 to Pr.239
Pr. 30
Pr. 30
Pr. 79
Pr. 11, Pr. 12
Pr. 127 to Pr. 134, Pr. 575 to Pr.
577
Pr. 79, Pr. 340
Pr. 17
Pr. 57, Pr. 58, Pr. 135 to Pr. 139,
Pr. 159
⎯
⎯
⎯
⎯
Pr. 9
Pr. 127 to Pr. 134
Pr. 79, Pr. 340
Pr. 79, Pr. 340
Pr. 338, Pr. 339
Pr. 30, Pr. 70
Pr. 30, Pr. 70
Pr. 127 to Pr. 134, Pr. 241, Pr.
553, Pr. 554, Pr. 575 to Pr. 577,
C42 to C45
⎯
Refer to
Page
88
93
119
161
90
142
237
101
88
108
108
181
106
225
187
118
237
120
120
120
⎯
101
225
189
189
190
108
108
225
⎯
4
117