B&D Diamond Series Instructions For The Use
  1. Manuals
  2. Brands
  3. B&D Manuals
  4. Garage Door Opener
  5. Diamond Series
  6. Instructions for the use

B&D Diamond Series Instructions For The Use

Hide thumbs
Table of Contents

Advertisement

Quick Links

QLD Office:
NSW Office:
VIC/TAS Office: 147-153 Canterbury Road
B&D Doors
New Zealand:
114A2991
INSTRUCTIONS
www.bnd.com.au
17 Oasis Court
Clontarf 4019
(07) 3883 0200
34-36 Marigold Street
Revesby 2212
(02) 9722 5555
Kilsyth 3137
(03) 9237 7766
70 Allens Road
EastTamaki
Auckland, New Zealand
(09) 273 8600
www.bnd.co.nz
SA Office:
23 Frederick Road
Royal Park 5014
(08) 8440 4747
WA Office:
96 Mulgul Road
Malaga 6090
(08) 9247 8777
C-Tick approval logo
min. size 3mm diam.;
letters min. 3mm high
The Controll-A-Door-P Diamond
has been tested and complies
with the standards:
AS/NZS 3350.2.95:2000
(incl. Amdt1) & AS/NZS
CISPR 14.1:2003
N1134

Advertisement

Table of Contents
loading

Related Manuals for B&D Diamond Series

Summary of Contents for B&D Diamond Series

  • Page 1 INSTRUCTIONS www.bnd.com.au QLD Office: 17 Oasis Court SA Office: 23 Frederick Road Clontarf 4019 Royal Park 5014 (08) 8440 4747 (07) 3883 0200 WA Office: 96 Mulgul Road NSW Office: 34-36 Marigold Street Malaga 6090 Revesby 2212 (08) 9247 8777 (02) 9722 5555 C-Tick approval logo VIC/TAS Office: 147-153 Canterbury Road...

  • Page 2: Table Of Contents

    IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION AND USE These safety alert symbols mean WARNING – a personal safety or property damage instruction. This garage door opener is designed and tested to offer reasonable safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions contained in this manual. WARNING –...

  • Page 3: Door Types

    BEFORE YOU BEGIN: DOOR TYPES A. One-Piece Door with Horizontal Track Only 1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural supports. B. Sectional Door with Curved Track: 2. Do you have a finished ceiling in your garage? If so, a support See Page 5 –...

  • Page 4: Assemble The Rail

    ASSEMBLY SECTION ASSEMBLE THE RAIL Grease inside edges of rail brace sections using grease (1). Place rail pieces (2) on flat surface for assembly. All four rail sections are interchangeable. Slide rail brace (3) onto rail section. Connect rail by sliding rail brace onto next rail section. Tap rail assembly (4) on piece of wood (5) until rail sections are flush.

  • Page 5: Attach Sprocket Cover

    ATTACH SPROCKET COVER INSTALLATION SECTION Place sprocket cover (1) on top of the opener (2), secure with Wear protective goggles when working overhead to protect screws (3). Install the trolley stop bolt (4), use the lock nut (5) your eyes from injury. provided.

  • Page 6: Install The Header Bracket

    INSTALL THE HEADER BRACKET ATTACH RAIL TO HEADER BRACKET NOTE: Refer to vertical centre and horizontal lines created in Position opener on garage floor below the header bracket. Use section “Position the Header Bracket” on page 4 for proper packing material to protect the cover. Raise rail until holes in the placement of header bracket.

  • Page 7: Hang The Opener

    J-STYLE TILT DOOR / ONE-PIECE DOOR WITHOUT TRACK ATTACH EMERGENCY RELEASE ROPE & HANDLE • With the door fully open and parallel to the floor, measure the Thread one end of rope (1) through hole in top of red handle so distance from the floor to the top of the door.

  • Page 8: Fasten Door Bracket

    W W ARN ARNING FASTEN DOOR BRACKET CAUTION CAUTION Follow instructions which apply to your door type as illustrated below or on the following page. Fibreglass, aluminum or lightweight steel garage doors A horizontal reinforcement brace should be long enough to WILL REQUIRE reinforcement BEFORE installation of be secured to two or three vertical supports.

  • Page 9: Program The Travel Limits

    ADJUSTMENT SECTION CONNECT DOOR ARM TO TROLLEY A. Sectional Door Installation: Close garage door and disengage the trolley as described in A. SETTING THE LIMITS Slide trolley about 50mm from door. Connect straight door arm Travel limits regulate the points at which the door will stop (1) to trolley door arm connector hole with a clevis pin (6).

  • Page 10: Force Adjustment

    FORCE ADJUSTMENT TEST THE SAFETY REVERSE SYSTEM The force, as measured on the closing edge of the door, The safety reverse system test is important. Garage should not exceed 400N (40kg). If the closing force is – door must reverse on contact with a 40mm 180 s 60 s 120 s...

  • Page 11: Install The Door Control

    INSTALL THE DOOR CONTROL Locate door control where the garage door is visible, away from door and door hardware and out of the reach of children. Mount at least 1.5m (5 feet) above the floor. Serious personal injury from a moving garage door may result from misuse of opener.
  • Page 12 INSTALL THE SAFETY INFRARED REVERSING SENSOR (See Accessories) Install this accessory for all installations on doors over 2.5m in height and when the closing force as measured on the – 180 s 60 s 120 s bottom of the door is over 400N (40kg). After opener has been installed and adjusted, The Safety Infrared Reversing Sensor accessory can be installed.

  • Page 13: Operation Of Your Opener

    CARE OF YOUR OPENER OPERATION OF YOUR OPENER Your opener can be activated by any of the following devices: When properly installed, opener will provide high performance • The wall mounted door control. Hold the push button down with a minimum of maintenance. The opener does not require until door starts to move.

  • Page 14: Problems

    10. Door opens but won't close: HAVING A PROBLEM? • Check The Safety Infrared Reversing Sensor (if you have 1. Opener doesn't operate from either door control or remote: installed this accessory). If the light is blinking, correct alignment. • Does the opener have electric power? Plug lamp into outlet. If it •...

  • Page 15: Special Features

    SPECIAL FEATURES A. Door within a door connection (If this feature is not installed, the jumper must remain intact.) If installed, the door must be closed during door within a door operation, and wiring must be correct. Remove jumper from terminal leads.

  • Page 16: Accessories

    ACCESSORIES WIRING INSTRUCTIONS FOR ACCESSORIES (1) Model 62266 1 Channel Remote Lighted Push Button: To opener terminals: Red-1 and White-2. (2) Model 62171 2 Channel Remote Outside Keylock: To opener terminals: Red-1 and White-2. (3) Model 62170 3 Channel Remote Safety Infrared Reversing Sensor: To opener terminals: White-2 and Black-3.

  • Page 17: Replacement Parts

    REPLACEMENT PARTS 41A5273-1 LOCK 12C810 171A28 10A20 10A19 41A5047 29B137 41B4101-1 83A11 41A4335E (433MHz) 41A5800 41B4494-1 210C42 7423CR3 (chain) 183D177 41A92 183D178 178B34 8423CR3 (belt) 12C778 8025CR3 (belt) 12C855 41B4103 41A3475-24 12A0644 41A5844 (2.3m) 178B35 41A5844-1 (2.5m) 4A1008 41A5844-2 (3.0m) 41A2828 31D537 114A2991...
  • Page 18 REPLACEMENT PARTS 171A543 31D525 28A95 158A49 171A498 26B72 41C67 (belt drive) 216A206 41B5348 171A479 37D117-2 41B4375-3 41C5392 171A315 41B5351-5 41A5696-4C 171A384-8 41C5350-8 171A384 41D605 171A545 41D163 108D56 171A320 114A2991...

  • Page 19: Specifications

    SPECIFICATIONS Input Voltage ....230-240V, 50Hz Max. Pull Force ..800N Power ......165W Normal Torque ...8Nm Stand-by power rating @ 230V ....6W Motor Type ......DC Permanent lubrication Volts ......24 V DC Drive Mechanism Length of Travel ..Adjustable to 3m Travel Rate ....12-17cm per second nom., 20-100% ramp Lamp ......1x230V/40W/E27 socket, on when door starts, off 2-1/2 minutes after stop.

  • Page 20: Warranty

    WARRANTY 10. Subject to Clause 12 hereof, this warranty does not extend to and B&D will be relieved of all obligations, responsibilities and liabilities (direct or Controll-A-Door Automatic Garage Door Opener ® consequential) in the event that defects in manufacture of the Opener are directly or indirectly in the opinion of B&D due to or result from: 1.

Table of Contents