1. Manuals
  2. Brands
  3. Town & Country Fireplaces Manuals
  4. Burner
  5. TCWS38
  6. Instructions for intallation

Town & Country Fireplaces TCWS38 Instructions For Intallation

Series c tranquility burner kit
Hide thumbs Also See for TCWS38:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation
and Operating Instructions supplied with the fireplace
and should be kept together. Refer to the Installation
and Operating Instructions for proper gas supply, safety
requirements and operating instructions.
050809-16
TCWS.38NG04.C
TRANQUILITY
BURNER KIT
INSTRUCTIONS
PART# TCWS.38NG04.C
For use with
Model TCWS38
Series C
5056.4252204
TCWS.38NG04.C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TCWS38 and is the answer not in the manual?

Questions and answers

Related Manuals for Town & Country Fireplaces TCWS38

Summary of Contents for Town & Country Fireplaces TCWS38

  • Page 1 Operating Instructions supplied with the fireplace and should be kept together. Refer to the Installation and Operating Instructions for proper gas supply, safety requirements and operating instructions. TCWS.38NG04.C TRANQUILITY BURNER KIT INSTRUCTIONS PART# TCWS.38NG04.C For use with Model TCWS38 Series C 050809-16 5056.4252204 TCWS.38NG04.C...

  • Page 2: Contents Of Package

    Contents of Package 5.0 lbS SaNd HaRdWaRE PaCK EQUalIZER ROCK 1/4 SS PIlOT SUPPlY TUbE PIlOT aSSEMblY bURNER aSSEMblIES bURNER TRaY aSSEMblY PEbblE SETS MaNIFOld bRaCKETS WITH 1/2” SS FUEl SUPPlY TUbES TCWS.38NG04.C 050809-16...
  • Page 3 Tranquility Burner Installation If converting to propane see conver- Fig #1 sion instructions on page #8 before proceeding. Install panels according to the TCWS.38CE Installation and Operating manual prior to burner installation. (Page 23) attach the manifold brackets, with the fuel supply tubes, to the bottom of the firebox using four screws.
  • Page 4 Fig #4 CAUTION: Ensure that all connections are gas tight. Tilt burner tray length-wise and insert Fig #5 into the firebox. (Fig. #5) attach pilot to burner tray. (Fig. #6) Fig #6 NOTE: Ensure tht the pilot is tight up against the burner tray.
  • Page 5 Secure the burner tray to legs using Fig #7 six screws (Fig. #7) NOTE: a light will aid aligning the holes in the tray with the leg Fig #8a Fig #8b NOTE: check air shutter for correct setting for fuel before proceeding lOCaTOR Tab further.
  • Page 6 Each rock has a slot in it’s base and is Fig #14 Fig #10 marked with a letter and an arrow. (Fig. #10) 10. Place each rock as per the following Fig #11 Fig #15 photographs, start from the right hand side of the burner and ensure that the arrow on each rock points towards the front of the fireplace.
  • Page 7 12. Place the remaining (a) rock on the Fig #21 Fig #18 left hand end of burner as shown. (Fig. #21) Fig #19 11. Repeat the sequence of placing the rocks two more times until the burner is covered. Fig #20 13.

  • Page 8: Propane Conversion Kit

    Propane Conversion If the unit is to be used on propane Fig #23 PROPANE CONVERSION KIT convert as follows using the compo- nents supplied with this burner: MINIMUM RaTE SCREW (5005.015) CAUTION The gas supply and electrical power shall be shut off before proceeding with the conversion.
  • Page 9 5. Slide the pilot adjustment band over and Fig #28b Fig #28a ensure that the hole in the orifice band is showing.(Fig. 28b) Retighten pilot head. Fig. #28a shows NG position Fig. #28b shows LP position). Remove the access panel on the right LP POSITION NG POSITION side of the firebox, 10 screws, and set...
  • Page 10 Fig #32 Fig #31 10. Press down on the center post and rotate Pull off the rubber cap from the top of 90°. The center post should stay down. the pressure regulator. (Fig. #32). Replace the rubber cap. (Fig. #31) Check all connections for leaks Fig #33 add daTE...

  • Page 11: Gas Pressure Check

    Gas Pressure Check Note: To test the gas pressure, turn off the gas supply before removing the plug from Fig #36 the supply pressure test port or manifold pressure test port. Verify gas pressures with the fireplace lit and on the highest setting. SUPPlY PRESSURE MaNIFOld...

  • Page 12: Burner Flame Adjustment

    Burner Flame Adjustment The air shutter on the venturi tube controls the primary combustion air. It is set to the closed position at the factory for natural gas fuel. For lP see Pg.8. Some adjustment may be neces- sary to obtain desired flame and to eliminate carbon deposits. Evaluate flame appearance after the fireplace has reached operating temperature.

  • Page 13: Replacement Parts

    Replacement Parts (WHEN ORdERING, INClUdE PaRT NUMbER WITH dESCRIPTION) ITEM..DESCRIPTION ..........PART NO. ITEM ..DESCRIPTION ..........PART NO. #7 ..PROPANE CONVERSION KIT..TCWS.38LPCE01 #1..TRANQUILITY BURNER KIT..TCWS.38NG04.C #8 ..SAND ..........TC36.SAND50 #2..PEBBLE ASSEMBLY ......5096.921 (3) #3..FUEL SUPPLY TUBE ......5019.223 #9..TRIM ROCK “A”...
  • Page 14 Notes:...
  • Page 15 Notes:...
  • Page 16 Technical support: 1-250-748-1184 Web site: www.townandcountryfireplaces.net 2975 Allenby Rd., Duncan, BC V9L 6V8 Printed in Canada...

This manual is also suitable for:

Tcws.38ng04.c

Table of Contents